Belkin ADSL2+ Modem User Manual
[insert Belkin logo]
ADSL2+ Modem
with Wireless G Plus MIMO
Router
.bj.kb;kgkvjf
Network your
computers and
share your ADSL
Internet access
User Manual
F5D9630-4
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Benefits of a Home Network . . . . . . . . . . . . . . . . . . . . . . . . . .1
Advantages of a Belkin Wireless Network . . . . . . . . . . . . . . . .1
2 Make Sure You Have the Following . . . . . . . . . . . . . . . . . . . . . . .2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Internet Connection Settings . . . . . . . . . . . . . . . . . . . . . . . . . .2
3 Knowing your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
4 Connecting your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Positioning your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connecting your Computers . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting your ADSL Line . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Powering Up your Router. . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5 Setting Up your Computers . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Manually Configuring Network Adapters . . . . . . . . . . . . . . . .12
Recommended Web Browser Settings. . . . . . . . . . . . . . . . . .17
6 Configuring your Router with the Setup Wizard . . . . . . . . . . .19
Running the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Connecting to the Wireless LAN . . . . . . . . . . . . . . . . . . . . . 20
7 Manually Configuring Your Router . . . . . . . . . . . . . . . . . . . . . .23
Understanding the Web-Based User Interface. . . . . . . . . . . .23
Changing LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Internet WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
9 Technical Support Information . . . . . . . . . . . . . . . . . . . . . . . . .76
10 Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Appendix A: Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Appendix B: Important Factors for Placement and Setup . . .83
Appendix C: Internet Connection Setting Table . . . . . . . . . . .85
11 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Introduction
Thank you for purchasing the Belkin ADSL Modem with High-Speed
Mode Wireless G Router (the Router). In minutes you will be able to
share your Internet connection and network your computers with your
new Router. The following is a list of features that make your Router an
ideal solution for your home or small office network. Please be sure to
read through this User Manual completely, and pay special attention to
Appendix B entitled “Important Factors for Placement and Setup”.
Benefits of a Home Network
By following our simple setup instructions, you will be able to use
your Belkin home network to:
• Share one high-speed Internet connection with all the computers
in your home
• Share resources, such as files, and hard drives among all the
connected computers in your home
• Share a single printer with the entire family
• Share documents, music, video, and digital pictures
• Store, retrieve, and copy files from one computer to another
• Simultaneously play games online, check Internet email,
and chat
Advantages of a Belkin Wireless Network
Mobility – you’ll no longer need a dedicated “computer room”— now you
can work on a networked laptop or desktop computer anywhere within
your wireless range
Easy installation – Belkin’s Easy Installation Wizard makes setup simple
Flexibility – set up and access printers, computers, and other
networking devices from anywhere in your home
Easy Expansion – the wide range of Belkin networking products let
you expand your network to include devices such as printers and
gaming consoles
No cabling required – you can spare the expense and hassle of
retrofitting Ethernet cabling throughout the home or office
Widespread industry acceptance – choose from a wide range of
interoperable networking products
Package Contents
• ADSL2+ Modem with Wireless G Plus MIMO Router
• RJ11 Telephone Cord - Gray
• RJ45 Ethernet Networking Cable - Yellow
• ADSL Microfilter*
• Power Adapter
• User Manual CD
*ADSL microfilter varies by country. If it’s not included, you will need to purchase
one.
System Requirements
• An active ADSL service with a telephone wall jack for connecting
the Router
• At least one computer with a Network Interface Card (NIC) and Internet
browser installed and correctly configured
• TCP/IP networking protocol installed on each computer connected to
the Router
• No other DHCP server on your local network assigning IP addresses to
computers and devices
Internet Connection Settings
Please collect the following information from your Internet Service Provider (ISP)
before setting up the ADSL Modem Wireless G Router.
• Internet connection protocol: _________ (PPPoE, PPPoA, Dynamic IP, Static IP)
• Multiplexing method or Encapsulation: __________ (LLC or VC MUX)
• Virtual circuit: VPI (Virtual Path Identifier) __________
(a number between 0 and 255)
• VCI (Virtual Channel Identifier) __________
(a number between 1 and 65535)
• For PPPoE and PPPoA users: ADSL account user name _____________ and
password _______________
• For static IP users: IP Address ___ . ___ . ___ . ___
Subnet Mask ___ . ___ . ___ . ___
Default Gateway Server ___ . ___ . ___ .
• IP address for Domain Name Server ___ . ___ . ___ . ___ (If given by your ISP)
Note: See Appendix C in this User Manual for some common DSL Internet
setting parameters. If you are not sure, please contact your ISP.
Knowing your Router
The Router is designed to be placed on a desktop. All of the cables exit from
the rear of the Router for better organization and utility. The LED indicators
are easily visible on the front of the Router to provide you with information
about network activity and status.
[replace the following section with the same section from F5D7633-4 see P74730uk]
Front Panel
[Insert: 9630-4 front image w/ arrows to LEDs]
1) [Insert: icon] Power LED
2) [Insert: icon] LAN Status LED (1-4)
3) [Insert: icon] Wireless LAN (WLAN) Status LED
4) [Insert: icon] ADSL LED
5) [Insert: icon] Internet
1. Power LED
When you apply power to the Router or restart it, a short period of time elapses
while the Router boots up. When the Router has completely booted up, the
Power LED becomes a GREEN light, indicating the Router is ready for use.
Insert:
Power
Icon
OFF Router is off
Green Router is on
Red Router failed to start
2. LAN Status LEDs
These LAN Status LEDs are labeled 1–4 and correspond to the numbered ports
on the rear of the Router. When a computer is properly connected to one of the
LAN ports on the rear of the Router, the LED will light. Solid GREEN means a
computer or a network-enabled device is connected. When information is being
sent over the port, the LED blinks rapidly. ORANGE indicates a 10Base-T
connection.
OFF No device is connected
Orange
Insert
LAN
Icon
3. WLAN Status LED
The WLAN Status LED is solid GREEN when you enable the wireless LAN
function. It flashes when the Router is transmitting or receiving data wirelessly.
Insert
WLAN
Icon
4. ADSL LED
The ADSL LED flashes GREEN during negotiation with your ISP. It stays
GREEN when the Router is connected properly to your ADSL service.
Insert
ADSL
Icon
5. Internet LED
The Internet LED shows you when the Router is connected to the Internet. When
the LED is OFF, the Router is NOT connected to the Internet. When the LED is
solid GREEN, the Router is connected to the Internet. When the LED is blinking,
the Router is transmitting or receiving data from the Internet.
Insert
Internet
Icon
Back Panel
[Insert: 9630-4 back image w/ arrows to ports]
Orange—blinking
Green
Green—blinking
OFF WLAN is off
Green WLAN is up and connected
Green—blinking
OFF No ADSL connection
Green – blinking Negotiating connection
Green ADSL link is up and connected
OFF No Internet connection
Green Connected to the Internet
Green – blinking
Red Failed to get IP
6) [Insert: icon] DSL Line
Ethernet link is up and
10Base-T device connected
When 10Base-T device
transmitting or receiving data
Ethernet link is up and
100Base-T connected
When 100Base-T device
transmitting or receiving data
When transmitting or receiving
data
When transmitting or receiving
data
7) [Insert: icon] Ethernet Ports (4–1)
8) [Insert: icon] Reset Button
9) [Insert: icon] Power Plug
6. DSL Line
This port is for connection to your ADSL line. Connect your ADSL line to this port.
7. Ethernet Ports
The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports are labeled 1
through 4. These ports correspond to the numbered LEDs on the front of the
Router. Connect your network-enabled computers or any networking devices to
one of these ports.
8. Reset Button
The “Reset” button is used in rare cases when the Router may function
improperly. Resetting the Router will restore the Router’s normal operation while
maintaining the programmed settings. You can also restore the factory default
settings by using the Reset button. Use the restore option in instances where you
may have forgotten your custom password.
a. Resetting the Router
Push and hold the Reset button for one second then release it. When the
Power/Ready light becomes solid again, the reset is complete.
b. Restoring the Factory Defaults
Press and hold the Reset button for five seconds then release it. When the
Power/Ready light becomes solid again, the restore is complete.
9. Power Plug
Connect the included 15V DC power supply to this inlet. Using the wrong type of
power adapter may cause damage to your Router.
Connecting your Router
Positioning your Router
Your wireless connection will be stronger the closer your computer
is to your Router. Typical indoor operating range for your wireless
devices is between 100 and 200 feet. In the same way, your w ireless
connection and performance will degrade somewhat as the distance
between your Router connected devices increases. This may or may
not be noticeable to you. As you move farther from your Router,
connection speed may decrease. Factors that can weaken signals
simply by getting in the way of your network’s radio waves are metal
appliances, or obstructions, and walls. Please see “Appendix B:
Important Factors for Placement and Setup” in this User Manual for
more guidelines.
If you have concerns about your network’s performance that m i ght be
related to range or obstruction factors, try moving the computer to
a position between five and 10 feet from the Router, in order to see
if distance is the problem. If difficulties persist even at close range,
please see the Troubleshooting section for solutions.
Connecting your Computers
1. Power off your computers and networking equipment.
2. Connect your computer to one of the YELLOW RJ45 ports on the
rear of the Router labeled “connections to your computers” by
using an Ethernet networking cable (one Ethernet network cable
is supplied).
[insert 9630-4 rear illustration. Can use the same image from F5D7633-4]
Connecting your ADSL Line
Connection for the Router to the ADSL line varies by country and
region. Typically it involves a microfilter or a microfilter with built-in
splitter to allow simultaneous use of ADSL service and telephone
service on the same telephone line. Please read the following steps
carefully and select appropriate method.
1. If your telephone service and ADSL service are on the same
telephone line, ADSL microfilters are needed for each telephone
and device, such as answering machine, fax machine, and caller
ID display. Additional splitters may be used to separate telephone
lines for telephone and the Router.
Note: Do not connect the ADSL microfilter between the wall jack
and the Router—this will prevent ADSL service from reaching
the modem.
2. If your telephone service and ADSL service are on the same
telephone line and you are using an ADSL microfilter with built-in
splitter, connect the splitter to the telephone wall jack providing
ADSL service. Then, connect the telephone cord from the ADSL
microfilter RJ11 port generally labeled “DSL” to the gray RJ11
port labeled “DSL line” on the back of your Router. Connect
telephony device to the other port on the ADSL splitter commonly
labeled “Phone”. An additional ADSL microfilter is needed for
another telephone and device on the same line.
[insert 9630-4 rear illustration. Can use the same image from F5D7633-4]
Note: One RJ11 telephone cord is supplied. When inserting an
RJ11 plug, be sure the tab on the plug clicks into position to
ensure that it is properly seated.
3. If you have a dedicated ADSL service telephone line with an RJ11
wall jack, simply connect a telephone cord from the wall jack to
the gray RJ11 port labeled “DSL line” on the back of
your Router.
4. If you have an RJ45 wall jack for your ADSL service, connect an
RJ45-to-RJ11 converter to the wall jack. Then connect one end of
a telephone cord to the converter and the other end to the gray
RJ11 port labeled “DSL line” on the back of your Router.
Note: ADSL microfilter may or may not be provided depending on
your country.
Powering Up your Router
1. Connect the supplied power adapter to the Router power-input
plug labeled “Power”.
Note: For safety and performance reasons, only use the supplied
power adapter to prevent damage to the Router.
[insert 9630-4 rear illustration. Can use the same image from F5D7633-4]
2. After connecting the power adapter and the power source is turned on,
the Router’s power icon on the front panel should be on. It might
take a few minutes for the Router to fully start up.
[insert 9630-4 front illustration. Can use the same image from F5D7633-4. If the product name is clearly visible, correct it to ADSL2+
Modem with Wireless G Plus MIMO Router]
3. Turn on your computers. After your computers boot up, the LAN
status LED on the front of the Router will be on for each port
to which a wired computer is connected. These lights show
you the connection and activity status. Now you are ready to
configure the Router for ADSL connection.
In order for your computer to properly communicate with your Router, you
will need to change your computer’s “TCP/IP Ethernet” settings to “Obtain
an IP address automatically/Using DHCP”. This is normally the default
setting in most home computers.
You can set up the computer that is connected to the ADSL modem FIRST
using these steps. You can also use these steps to add computers to your
Router after the Router has been set up to connect to the Internet.
Manually Configuring Network Adapters in Windows XP, 2000, or NT
Click “Start”, “Settings”, then “Control Panel”.
1.
2. Double-click on the “Network and dial-up connections” icon
(Windows 2000) or the “Network” icon (Windows XP).
3. Right-click on the “Local Area Connection” associated with your
network adapter and select “Properties” from the drop-down menu.
4. In the “Local Area Connection Properties” window, click “Internet
Protocol (TCP/IP)” and click the “Properties” button. The following
screen will appear:
[Use existing screenshot]
(1)
(2)
(3)
5. If “Use the fol l owing IP add ress” (2) is selected, your Router will need to
be set up for a static IP connection type. Write the address information
the table below. You will need to enter this information into the Router.
[Use existing screenshot]
6. If not already selected, select “Obtain an IP address automatically”
(1) and “Obtain DNS server address automatica lly” (3). Click “OK”.
Your network adapter(s) are now configured for use with the Router.
Manually Configuring Network Adapters in Windows 98SE or Me
Right-click on “My Network Neighborhood” and select “Properties” from
1.
the drop-down menu.
2. Select “TCP/IP -> settings” for your installed network adapter. You will
see the following window.
[Use existing screenshot]
(1)
(2)
(3)
3. If “Specify an IP address” is selected, your Router will need to be set up
for a static IP connection type. Write the address information in the table
below. You will need to enter this information into the Router.
[Use existing screenshot]
4.
Write the IP address and subnet mask from the “IP Address” tab (3).
5. Click the “Gateway” tab (2). Write the gateway address down in the chart.
6. Click the “DNS Configuration” tab (1). Write the DNS address(es) in the chart.
7. If not already selected, select “Obtain an IP address automatically” on the
IP address tab. Click “OK”.
8. You will also need to delete the Gateway address from the Gateway tab
and DNS Configuration entries in order to properly be configured for
connection to the Belkin router.
Restart the computer. When the computer restarts, your network
adapter(s) are now configured for use with the Router.
Set up the computer that is connected to the cable or DSL modem
by FIRST using these steps. You can also use these steps to add
computers to your Router after the Router has been set up to connect
to the Internet.
Manually Configuring Network Adapters in Mac OS
up to 9.x
In order for your computer to properly communicate with your Router,
you will need to change your Mac computer’s TCP/IP settings to DHCP.
1. Pull down the Apple menu. Select “Control Panels” and
select “TCP/IP”.
2. You will see the TCP/IP control panel. Select “Ethernet Built-In”
or “Ethernet” in the “Connect via:” drop-down menu (1).
[Use existing screenshot]
(1)
(2)
Next to “Configure” (2), if “Manually” is selected, your Router
3.
will need to be set up for a static IP connection type. Write the
address information in the table below. You will need to enter this
information into the Router.
[Use existing screenshot]
If not already set, at “Configure:”, choose “Using DHCP
4.
Server”. This will tell the computer to obtain an IP address
from the Router.
[Use existing screenshot]
5. Close the window. If you made any changes, the foll owing
window will appear. Click “Save”.
Restart the computer. When the computer restarts, your network
settings are now configured for use with the Router.
[Use existing screenshot]
Manually Configuring Network Adapters in Mac OS X
1. Click on the “System Preferences” icon.
[Use existing screenshot]
Select “Network” (1) from the “System Preferences” menu.
2.
[Use existing screenshot]
(1)
3. Select “Built-in Ethernet” (2) next to “Show” in the
Network menu.
[Use existing screenshot]
(2)
(3)
(4)
4. Select the “TCP/IP” tab (3). Next to “Configure” (4), you should
see “Manually” or “Using DHCP”. If you do not, check the
PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT
selected. If it is, you will need to configure your Router for a
PPPoE connection type using your user name and password.
5. If “Manually” is selected, your Router will need to be set up
for a static IP connection type. Write the address information
in the table below. You will need to enter this information into
the Router.
[Use existing screenshot]
6. If not already selected, select “Using DHCP” next to “Configure”
(4), then click “Apply Now”.
Your network adapter(s) are now configured for use with the Router.
Recommended Web Browser Settings
In most cases, you will not need to make any changes to your web
browser’s settings. If you are having trouble accessing the Internet or
the advanced web-based user interface, then change your browser’s
settings to the recommended settings in this section.
Internet Explorer 4.0 or Higher
[insert updated screenshots]
IE6_Internet_Options.jpg
1.
Start your web browser. Select “Tools” then “Internet Options”.
2. In the “Internet Options” screen, there are three selections:
“Never dial a connection”, “Dial whenever a network connection
is not present”, and “Always dial my default connection”. If you
can make a selection, select “Never dial a conn ection”. If you
cannot make a selection, go to the next step.
IE6_Internet_Options_Connections.jpg
3. Under the “Internet Options” screen, click on “Connections” and
select “LAN Settings…”.
18
4. Make sure there are no check marks next to any of the displayed
options: “Automatically detect settings”, “Use automatic
configuration script”, and “Use a proxy server”. Click “OK”. Then
click “OK” again in the “Internet Options” page.IE6_Internet_Options_Connections_LAN_Settings.jpg
Netscape Navigator 4.0 or Higher
1.
Start Netscape. Click on “Edit” then “Preferences”.
2. In the “Preferences” window, click on “Advanced” then select
“Proxies”. In the “Proxies” window, select “Direct connection to
the Internet”.
[Use existing screenshot]
Running the Setup Wizard
1. You can access the web-based management user interface of the
Router using the Internet browser on a computer connected to
the Router. Type “192.168.2.1” (do not type in anything else such
as “http://” or “www”) in your browser’s address bar. Then press
the “Enter” key.
[insert 9630_IP_Address.tif]
Note: It is strongly recommended that you use a computer
physically connected to the Router with an RJ45 cable for initial
setup. Using a wirelessly connected computer for initial setup is
not recommended.
2. The following screen will appear in your browser to prompt you to log
in. The Router ships with no password entered. In the login screen,
leave the password blank and click the “Submit” button to log in.
[insert 9630_Login.tif]
Note: It is strongly recommended that you change the password
to your own for increased security. Please read the following
section, entitled “Manually Configuring your Router”, for details
on how to change your password and to reference other
security features.
Understanding the Web-Based User Interface
The home page shows you a quick view of the Router’s status and
settings. All advanced setup pages can be reached from this page.
[insert 9630_Home.tif]
(1)
(9)
(2) (5) (4) (3) (10)
(6)
(8)
(7)
1. Quick-Navigation Links
You can go directly to any of the Router’s UI pages by clicking
directly on these links. The links are divided into logical
categories and grouped by tabs to make finding a particular
setting easier to find. Clicking on the header of each tab will
show you a short description of the tab’s function.
2. Home Button
The “Home” button is available in every page of the UI. Pressing
this button will take you back to the home page.
3. Help Button
The “Help” button gives you access to the Router’s help pages.
Help is also available on many pages by clicking “more info” next
to certain sections of each page.
4. Login/Logout Button
This button enables you to log in and out of the Router with the
press of one button. When you are logged into the Router, this
button will change to read “Logout”. Logging into the Router will
take you to a separate login page where you will need to enter a
password. When you are logged into the Router, you can make
changes to the settings. When you are finished making changes,
you can log out of the Router by clicking the “Logout” button.
For more information about logging into the Router, see the
section called “Logging into the Router”.
5. Internet Status Indicator
This indicator is visible in all pages of the Router, showing
the connection status of the Router. When the indicator says
“connection OK” in GREEN, the Router is connected to the
Internet. When the Router is not connected to the Internet, the
indicator will read “no connection” in RED. The indicator is
automatically updated when you make changes to the settings of
the Router.
6. LAN Settings
Shows you the settings of the Local Area Network (LAN) side of
the Router. Changes can be made to the settings by clicking the
“LAN” “Quick Navigation” link on the left side of the screen.
7. Features
Shows the status of the Router’s UPnP, NAT, and firewall
features. Changes can be made to the settings by clicking on any
one of the links or by clicking the “Quick Navigation” links on the
left side of the screen.
8. Internet Settings
Shows the settings of the Internet/WAN side of the Router that
connects to the Internet. Changes to any of these settings can be
made by clicking on the “Internet/WAN” “Quick Navigation” link
on the left side of the screen.
9. Version Info
Shows the firmware version, boot-code version, hardware
version, and serial number of the Router.
10. Page Name
The page you are on can be identified by this name. This manual
will sometimes refer to pages by name. For instance, “LAN > LAN
Settings” refers to the “LAN Settings” page.
Changing LAN Settings
All settings for the internal LAN setup of the Router can be viewed
and changed here.
Clicking on the header of the LAN tab
tab’s header page. A quick description of the functions can be
found here. To view the settings or make changes to any of the LAN
settings, click on “LAN Settings”
computers, click on “DHCP Client List”
[insert 963_LAN.tif]
(1) will take you to the LAN
(2) or to view the list of connected
(3).
(1)
(2)
(3)
LAN Settings
[insert 9630_LAN_Settings.tif]
(1)
(2)
(3)
(4)
(5)
(6)
1. IP Address
The “IP address” is the internal IP address of the Router.
The default IP address is “192.168.2.1”. To access the setup
interface, type this IP address into the address bar of your
browser. This address can be changed if needed. To change
the IP address, type in the new IP address and click “Apply
Changes”. The IP address you choose should be a non-routable
IP. Examples of a non-routable IP are:
192.168.x.x (where x is anything between 0 and 255)
10.x.x.x (where x is anything between 0 and 255)
2. Subnet Mask
There is no need to change the subnet mask as the router will
automatically adjust the length based on the IP address type.
3. DHCP Server
The DHCP server function makes setting up a network very easy
by assigning IP addresses to each computer on the network
automatically. The default setting is “On”. The DHCP server can
be turned OFF if necessary, however, in order to do so you must
manually set a static IP address for each computer on your network.
To turn off the DHCP server, select “Off” and click “Apply Changes”.
4. IP Pool
The IP Pool is the range of IP addresses set aside for dynamic
assignment to the computers on your network. The default is
2–100 (99 computers). If you want to change this number, you
can do so by entering a new starting and ending IP address and
clicking on “Apply Changes”. The DHCP server can assign 100 IP
addresses automatically. This means that you cannot specify an
IP address pool larger than 100 computers. For example, starting
at 50 means you have to end at 150 or lower so as not to exceed
the 100-client limit. The starting IP address must be lower in
number than the ending IP address.
5. Lease Time
Lease time is the length of time the DHCP server will reserve
the IP address for each computer. We recommend that you
leave the lease time set to “Forever”. The default setting is
“Forever”, meaning that any time a computer is assigned an
IP address by the DHCP server, the IP address will not change
for that particular computer. Setting lease times for shorter
intervals, such as one day or one hour, frees IP addresses after
the specified period of time. This also means that a particular
computer’s IP address may change over time. If you have set any
of the other advanced features of the Router, such as DMZ or
client IP filters, these are dependent on the IP address. For this
reason, you will not want the IP address to change.
6. Local Domain Name
The default setting is “Belkin”. You can set a local domain name
(network name) for your network. There is no need to change this
setting unless you have a specific advanced need to do so. You can
name the network anything you want such as “MY NETWORK”.
DHCP Client List
You can view a list of the computers (known as clients), which are
connected to your network. You are able to view the IP address
the computer, the host name
one), and the MAC address
Card (NIC). Pressing the “Refresh”
there have been any changes, the list will be updated.
(2) (if the computer has been assigned
(3) of the computer’s Network Interface
(4) button will update the list. If
(1) of
[insert 9630_DHCP_Client.tif]
(1) (2) (3)
(4)
Internet WAN
The “Internet WAN” tab is where you will set up your Router to connect
to your Internet Service Provider. The Router is capable of connecting
to virtually any ADSL Service Provider’s system provided you have
correctly configured the Router’s settings for your ISP’s connection type.
Your connection settings are provided to you by your ISP. To configure
the Router with the settings that your ISP gave you, click “Connection
Type”
(1) on the left side of the screen. Select the connection type you
use. If your ISP gave you DNS settings, clicking “DNS”
enter DNS address entries for ISPs tha t require specific settings.
When you have finished making settings, the “Internet Status” indicator
will read “Connection OK” if your Router is set up properly.
[insert 9630_Internet_WAN.tif]
(2) allows you to
(1)
(2)
Connection Type
From the “Connection Type” page, you can select one of these five
connection types based on the instruction provided by your ISP:
• PPPoE
• PPPoA
• Dynamic IP (1483 Bridged)
• Static IP (IPOA)
• Modem Only (Disable Internet Sharing)
Note: See Appendix C in this User Manual for some common DSL
Internet setting parameters. If you are not sure, please contact your ISP.
Select the type of connection you use by clicking the radio button
next to your connection type and then clicking “Next” (2).
[insert 9630_Connection_Type.tif]
(1)
(1)
(2)
Setting your ISP Connection Type to PPPoE or PPPoA
PPPoE (Point-to-Point Protocol over Ethernet) is the standard
method of connecting networked devices. It requires a user name and
password to access the network of your ISP for connecting to the
Internet. PPPoA (PPP over ATM) is similar to PPPoE, but is mostly
implemented in the UK. Select PPPoE or PPPoA and click “Next”.
Then enter the information provided by your ISP, and click “Apply
Changes” to activate your settings.
[insert 9630_PPPoE.tif]
(1)
(2)
(3)
(4)
(5)
(6)
(7)
1. User Name - Enter the user name. (Assigned by your ISP).
2. Password - Enter your password. (Assigned by your ISP).
3. Retype Password - C onf irm the password. (Assigned by your ISP).
4. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameter here. (Assigned by your ISP).
5. Encapsulation - Select your encapsulation type (supplied by your ISP)
to specify how to handle multiple protocols at the ATM transport layer.
VC-MUX: PPPoA Virtual Circuit Multiplexer (null encapsulation) allows
only one protocol running per virtual circuit with fewer overheads.
LLC: PPPoA Logical Link Control allows multiple protocols running over
one virtual circuit (more overhead).
6. Dial on Demand - By selecting “Dial on Demand” your Router will
automatically connect to the Internet when a user opens up a web browser.
7. Idle Time (Minutes) - Enter the maximum idle time for the Internet
connection. After this time has been exceeded, the connection will
be terminated.
PPPoA
Setting your Connection Type to Dynamic IP (1483 Bridged)
This connection method bridges your network and ISP’s network
together. The Router will obtain an IP address automatically from your
ISP’s DHCP server.
[insert 9630_Dynamic_IP.tif]
(1)
(2)
1. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameter here. These identifiers are assigned by your ISP.
2. Encapsulation - Select LLC or VC MUX your ISP uses.
Setting your ISP Connection to S tatic IP (IPoA)
This connection type is also called “Classical IP over ATM” or “CLIP”,
which your ISP provides a fixed IP for your Router to connect to
the Internet.
Loading...