BELINEA 1945 G1 User Manual
ENGLISH
INTRODUCTION
This manual will familiarize you with the installation
and use of your Belinea monitor. Please take the time
to look through these instructions even if you are familiar with monitors.
We have taken all possible care to ensure that this
manual contains correct and accurate information.
However the manufacturer cannot assume liability for
any possible errors. In addition, the manufacturer can
not guarantee that the hardware will meet the purpose you require. We would appreciate reports of any
errors, suggestions or criticism.
© Copyright 2006,
MAXDATA Systeme GmbH,
45768 Marl, Germany,
www.maxdata.com
Editing, DTP and translation by Linguagem, www.Linguagem.de.
All rights reserved. No part of this manual may be reproduced, processed or distributed in any form (print,
photocopy, microfilm or any other process) or processed, duplicated or distributed by an electronic system without prior written permission from the
manufacturer.
We reserve the right to make changes according to
the technical progress. Belinea is an internationally
registered trademark. Other brand names may be reg
istered trademarks and must be treated as such.
Environment protection
We are all responsible for the environment: As many
of our customers are already familiar with monitors
we have not printed this manual in order to save paper
and by this protect our environment. Help to protect
the environment and only print the pages you need.
-
-
TABLE OF CONTENTS
INTRODUCTION...................................................... 1
IMPORTANT INFORMATION................................... 2
UNPACKING ............................................................. 2
MOUNTING .............................................................. 3
CONNECTION .......................................................... 3
START UP................................................................. 3
ERGONOMICS ......................................................... 4
CONFIGURATION..................................................... 4
SETTINGS................................................................. 5
CARING FOR YOUR MONITOR ............................... 7
TROUBLESHOOTING............................................... 8
TECHNICAL SPECIFICATIONS................................. 9
MAXDATA WARRANTY ........................................... 9
Guide to symbols
The symbols below are used in this manual to indicate
where there is risk of injury or damaging devices or to
indicate specially useful information.
DANGER! Indicates risk of injury. When not
following the instructions, severe injury or
death may result.
ATTENTION! Indicates possible damage to devices. When not following instructions, devices may be heavily damaged.
IMPORTANT! Indicates hints on operation and
other useful information.
Belinea 1945 G1 - Operating Instructions - 1
IMPORTANT INFORMATION
ENGLISH
Note on monitor placement
• The setup location must not be extremely hot,
cold, humid or dusty. Heat and cold can impair
the functionality of the monitor. Humidity and
dust can cause the monitor to fail.
• Do not place the monitor near heat sources
such as heaters or radiators. Do not expose
the monitor to mechanical vibrations or jarring.
Notes on power connection
Only use the power cord designated for use in
your country.
The wall outlet should be within easy reach.
Pulling the power plug is the only way to disconnect the monitor from the power source.
This monitor is ENERGY STAR®-compatible.
MAXDATA is an ENERGY STAR®- partner and
guarantees that this monitor complies with the
ENERGY STAR® guidelines for optimising
power consumption.
Safety instructions for operation
The power cord must not be damaged. Do not
place any objects on the power cord and make
sure it does not have any knots. To unplug the
cord, always pull on the plug and not on the cable itself. Damage to the power cord may result in fire or cause electric shocks.
• Avoid covering the ventilation slots. Air circulation is necessary to prevent the monitor from
overheating. If the air circulation is restricted, it
could cause fire or damage the monitor.
• Do not use any solvents to clean the monitor,
as the housing could be damaged. For more information about cleaning the monitor see section “Caring for your monitor” on page7.
Make sure that no humidity or liquids can enter
the monitor.
Never open the monitor housing yourself.
There is a danger of electric shocks and other
hazards. The monitor may only be opened and
services by qualified professionals.
UNPACKING
Scope of supply
Check if the delivery is complete.
12 34
56 7
1 Monitor
2 Instructions
3CD
4 Power cord
5 Audio cable
6 VGA cable
7 DVI cable (option)
Handling the monitor
Carefully lift the monitor out of the packaging.
• The monitor's LCD screen surface is very sensitive! Please avoid any pressure on the surface (finger, pencil etc.) and be especially
cautious during transportation since jolts and
shocks can cause the screen to become
scratched (always use the original packaging).
Keep the original box and packaging material in case
you have to ship or transport the monitor.
Intended purpose
This monitor developed as a display for computers.
Belinea 1945 G1 - Operating Instructions - 2
MOUNTING
ENGLISH
Mounting on the base
Only remove the safety pin from the back of
the base, if the monitor stands firmly on the
base.
Insert the shaft into the base until it locks in.
CONNECTION
1 Make sure that the monitor and the PC are
disconnected from the mains supply.
Connecting to an analogue graphics
card
You can connect the monitor to an analogue graphic
board or to a digital graphics card.
Connect the plugs carefully in order not to
bend the pins.
1 Connect the supplied signal cable to the socket D-
SUB.
2 Connect the other end of the signal cable to the
output socket of your graphics card.
Wall mounting
The monitor is shipped with the standard desktop
configuration. However, you can optionally mount the
device on a wall or on a monitor swivel arm (optional
accessory). For mounting remove the screws from
the back of the monitor (4 screws). Use a VESA com
patible support (4-hole assembly of 100 x 100 mm according the international VESA FDMI standard) and
follow the corresponding instructions.
2 Plug the other end of the audio cable into the
output socket on the PC.
D-SUBDVIAUDIO IN
AUDIO
DVI
VGA
-
Connecting to a digital graphics card
1 Connect the optional signal cable to the socket
DVI.
2 Connect the other end of the signal cable to the
output socket of your graphics card.
Audio connection
If you PC has a separate audio output, use the audio
cable to connect the monitor to the PC.
1 Connect the supplied audio cable to the socket
AUDIO IN.
START UP
1 Switch your PC on.
2 Press the button [ ] on the front of the monitor.
The status indicator beside the button [ ] lights up
green or orange.
Mains connection
1 Connect the supplied power cable to the socket
AC IN.
2 Plug the other end of the power cable into a
grounded wall outlet.
3 Reconnect your PC to the mains supply.
Green = monitor active
Orange = monitor on stand-by (power save mode).
Belinea 1945 G1 - Operating Instructions - 3
ERGONOMICS
ENGLISH
The best alignment
Align the monitor in such a way, that distance and angle correspond to the figure.
~70
ca. 35° 60°
90°
The best height
To adjust the height of the monitor, remove
the metal pin on the back of the base. Make
sure that the monitor stands firmly on the base, when
removing the pin.
Ergonomically, your posture is best when elbows, pelvis, knees and ankles are all at right angles.
Furthermore, you should regularly focus on an object
around 6 m away from you to help your eyes relax.
Putting the monitor in upright position
If needed, you can turn the monitor so that the screen
is in an upright position (Pivot function). Use the soft
ware settings to adapt the picture accordingly.
-
Non-reflecting operation
Adjust the monitor so that there are no reflections of
direct sunlight or direct light on the screen. By this,
you protect your eyes from excessive strain.
This monitor meets the requirements for non-reflection. This makes it suitable for normal office applications and you do not need to take any special
additional measures.
CONFIGURATION
Windows® 9x/ME/2,000 and XP
If using the monitor under Windows® 9x/ME/2000
and XP, we strongly recommend installing the Belinea
configuration file. You can obtain this file from your
Belinea dealer or download it from the MAXDATA FTP
server at ftp.maxdata.com. Here click the
"Belinea_Treiber_Driver" directory and download the
Belinea.inf and README_Belinea.TXT files. Follow
the instructions in the README-Belinea.TXT file.
Windows® NT 4.0
Under Windows® NT 4.0 no separate setup file is required. Select the vertical frequency and the number
of colours directly on your PC within the "Start” J
“Settings” J “Control Panel” J “Display” J “Set
tings” menu.
-
Belinea 1945 G1 - Operating Instructions - 4
Loading...