Beko V320S, V 320 X, V322 P, V322 S, V322 PX User Manual

GNE V322 S

GNE V 320 X GNEV320S

GNE V322 P

Refrigerator

Холодильник

Réfrigérateur Kühlschrank

Frigorífico Frigorifero

Šaldytuvas

Холодильники

Koelka st

Хладилник

Hűtőszekrény

Frižider

GNE V322 PX

Please read this manual first!

This means that this product must be handled pursuant to European Directive

the environment. For further information, please contact your local or regional

Recycling

Dear Customer, We hope that your product, which has been produced in modern plants and

checked under the most meticulous quality control procedures, will provide you an effective service.

For this, we recommend you to carefully read the entire manual of your product before using it and keep it at hand for future references.

This manual

• Will help you use your appliance in a fast and safe way.

• Read the manual before installing and operating your product.

• Follow the instructions, especially those for safety.

• Keep the manual in an easily accessible place as you may need it later.

• Besides, read also the other documents provided with your product.

Please note that this manual may be valid for other models as well.

Symbols and their descriptions

This instruction manual contains the following symbols:

Important information or useful usage tips.

C A Warning against dangerous conditions for life and property. B Warning against electric voltage.

This product is supplied with the selective sorting symbol for waste electrical

and electronic equipment (WEEE).

2002/96/EC in order to be recycled or dismantled to minimise its impact on

authorities.

Electronic products not included in the selective sorting process are potentially

www.beko.com

dangerous for the environment and human health due to the presence of

hazardous substances.

This product was manufactured using the latest technology in environmentally friendly conditions.

CONTENTS

1 Your Refrigerator 3 2 Important Safety Warnings 4

Intended use ........................................ 4

For products with a water dispenser; Child safety HCA Warning Things to be done for energy saving

Reccomendations for freshfood

compartment

.......................................... 6

....................................... 6

....................................... 7

.... 6

..... 7

3 Installation 8

Points to be considered when retransporting your refrigerator

Before operating your refrigerator

Electric connection............................... 9

Disposing of the packaging Disposing of your old refrigerator Placing and Installation Floor balance adjustment Adjusting the gap between the upper

.................................................. 12

door Installing Water Filter Connection of the Water Pipe to the

Refrigerator

Connection of Water Hose to the Jug Connection of the Water Pipe to the Cold

Water Mains Line Prior to first use of Ice/Water Dispenser

........................................ 14

.............................. 16

................ 8

......... 8

.................. 9

.......... 9

......................... 9

................... 10

......................... 13

4 Preparation 19

5 Using your refrigerator 20

Setting the fridge compartment temperature

Setting the freezer compartment temperature

Fresh Freeze Function

Quick Cool Function........................... 22

Vacation Button Auto Eco Button (Special Economy

function)

Ioniser ............................................... 22

Key Lock Button

Water Dispenser Illumination Water/Ice Type Selection Ice/Water Dispenser Using the Ice Dispenser Ice Off Using the water spring Spillage Tray

Sliding Body Shelves Blue light

................................................... 25

Ion: Egg tray Fresh Freeze Compartment

Crisper humidity control sliders........... 25

Recommendations for preservation of

frozen food Defrosting

Replacing the Interior Light Bulb

....................................... 21

........................ 21

................................. 22

............................................ 22

................................ 22

.............. 22

.................... 22

........................... 22

..................... 23

................................................ 23

....................... 24

...................................... 24

.......................... 24

........................................... 25

............................................. 25

................ 25

........................................ 26

.......................................... 26

......... 26

6 Maintenance and cleaning 28

Protection of plastic surfaces ............ 28

Chiller compartment Icebox and Water Dispenser

........................... 29

.............. 29

7 Recommended solutions for the problems 30

1 Your Refrigerator

*21

*20

*23

*10

*1718

*11

*12

1. Freezer compartment

2. Fridge compartment

3. Fridge compartment interior light

4. Butter and cheese lid

5. Fan

6. Ioniser

7. Fridge compartment glass shelves

8. Egg tray

9. Fridge compartment door racks

10. Wine cellar

11. Chiller compartment

12. Bottle holder

13. Bottle shelves

C Figures that take place in this instruction manual are schematic and may not

correspond exactly with your product. If the subject parts are not included in the

14. Crisper compartments

15. Crisper cover

16. Adjustable front legs

17. Blue light

18. Water reservoir

19. Ventilation lid

20. Freezer compartment drawers

21. Freezer Compartment glass shelves

22. Ice duct lid

23. Freezer compartment interior light

24. Fresh Freeze compartment

25. Ice container * OPTIONAL

product you have purchased, then it is valid for other models.

2 Important Safety Warnings

Please review the following information. Failure to observe this information may cause injuries or material damage. Otherwise, all warranty and reliability commitments will become invalid.

The usage life of the unit you purchased is 10 years. This is the period for keeping the spare parts required for the unit to operate as described.

Intended use

This product is intended to be used – indoors and in closed areas such as

homes;

– in closed working environments such

as stores and offices;

– in closed accommodation areas such

as farm houses, hotels, pensions.

• This product should not be used

outdoors.

General safety

• When you want to dispose/scrap

the product, we recommend you to consult the authorized service in order to learn the required information and authorized bodies.

• Consult your authorized service for

all your questions and problems related to the refrigerator. Do not intervene or let someone intervene to the refrigerator without notifying the authorised services.

• For products with a freezer

compartment; Do not eat cone ice cream and ice cubes immediately

after you take them out of the freezer

compartment! (This may cause

frostbite in your mouth.)

• For products with a freezer

compartment; Do not put bottled and canned liquid beverages in the freezer compartment. Otherwise, these may burst.

• Do not touch frozen food by hand;

they may stick to your hand.

• Unplug your refrigerator before

cleaning or defrosting.

• Vapor and vaporized cleaning

materials should never be used in cleaning and defrosting processes of your refrigerator. In such cases, the vapor may get in contact with the electrical parts and cause short circuit or electric shock.

• Never use the parts on your

refrigerator such as the door as a means of support or step.

• Do not use electrical devices inside

the refrigerator.

• Do not damage the parts, where

the refrigerant is circulating, with drilling or cutting tools. The refrigerant that might blow out when the gas channels of the evaporator, pipe extensions or surface coatings are punctured causes skin irritations and eye injuries.

• Do not cover or block the ventilation

holes on your refrigerator with any material.

• Electrical devices must be repaired by only authorised persons. Repairs

performed by incompetent persons create a risk for the user.

• In case of any failure or during

a maintenance or repair work, disconnect your refrigerator’s mains supply by either turning off the relevant fuse or unplugging your appliance.

• Do not pull by the cable when pulling

off the plug.

• Place the beverage with higher proofs

tightly closed and vertically.

• Never store spray cans containing

flammable and explosive substances in the refrigerator.

• Do not use mechanical devices

or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

• This product is not intended to be

used by persons with physical, sensory or mental disorders or unlearned or inexperienced people

(including children) unless they are

attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product

• Do not operate a damaged

refrigerator. Consult with the service agent if you have any concerns.

• Electrical safety of your refrigerator

shall be guaranteed only if the earth system in your house complies with standards.

• Exposing the product to rain, snow,

sun and wind is dangerous with respect to electrical safety.

• Contact authorized service when

there is a power cable damage to avoid danger.

• Never plug the refrigerator into

the wall outlet during installation. Otherwise, risk of death or serious injury may arise.

• This refrigerator is intended for only

storing food items. It must not be used for any other purpose.

• Label of technical specifications is

located on the left wall inside the refrigerator.

• Never connect your refrigerator to

electricity-saving systems; they may damage the refrigerator.

• If there is a blue light on the

refrigerator, do not look at the blue light with optical tools.

• For manually controlled refrigerators,

wait for at least 5 minutes to start the refrigerator after power failure.

• This operation manual should be

handed in to the new owner of the product when it is given to others.

• Avoid causing damage on power

cable when transporting the

refrigerator. Bending cable may cause fire. Never place heavy objects on

power cable. Do not touch the plug with wet hands when plugging the product.

• Do not plug the refrigerator if the wall

outlet is loose.

• Water should not be sprayed directly

on inner or outer parts of the product for safety purposes.

• Do not spray substances containing

inflammable gases such as propane gas near the refrigerator to avoid fire and explosion risk.

• Never place containers filled with

water on top of the refrigerator, otherwise this may cause electric shock or fire.

• Do not overload your refrigerator

with excessive amounts of food. If overloaded, the food items may fall down and hurt you and damage refrigerator when you open the door.

Never place objects on top of the

refrigerator; otherwise, these objects may fall down when you open or close the refrigerator's door.

• As they require a precise

temperature, vaccines, heat-sensitive medicine and scientific materials and etc. should not be kept in the refrigerator.

• If not to be used for a long time,

refrigerator should be unplugged. A possible problem in power cable may cause fire.

• The plug's tip should be regularly

cleaned; otherwise, it may cause fire.

• The plug’s tip should be cleaned regularly with a dry cloth; otherwise, it may cause fire.

• Refrigerator may move if adjustable

legs are not properly secured on the floor. Properly securing adjustable legs on the floor can prevent the refrigerator to move.

• When carrying the refrigerator, do not

hold it from door handle. Otherwise, it may be snapped.

• When you have to place your product

next to another refrigerator or freezer, the distance between devices should be at least 8cm. Otherwise, adjacent side walls may be humidified.

For products with a water dispenser;

Pressure of water mains should be

minimum 1 bar. Pressure of water mains should be maximum 8 bars.

• Use only potable water.

Child safety

• If the door has a lock, the key should

be kept away from reach of children.

• Children must be supervised to

prevent them from tampering with the product.

HCA Warning

If your product's cooling system contains R600a:

This gas is flammable. Therefore, pay attention to not damaging the cooling system and piping during usage and transportation. In the event of damage, keep your product away from potential fire sources that can cause the product catch a fire and ventilate the room in which the unit is placed.

Ignore this warning if your product's cooling system contains R134a.

Type of gas used in the product is stated in the type plate which is on the left wall inside the refrigerator.

Never throw the product in fire for

disposal.

Things to be done for energy

temperature

sensor

food

MILK

juice etc.

temperature

sensor

MILK

juice etc.

temperature

sensor

saving

• Do not leave the doors of your

refrigerator open for a long time.

• Do not put hot food or drinks in your

refrigerator.

• Do not overload your refrigerator so

that the air circulation inside of it is not prevented.

• Do not install your refrigerator

under direct sunlight or near heat emitting appliances such as ovens, dishwashers or radiators.

• Pay attention to keep your food in

closed containers.

• For products with a freezer

compartment; You can store maximum amount of food items in the freezer when you remove the shelf or drawer of the freezer. Energy consumption value stated for your refrigerator has been determined by removing freezer shelf or drawer and under maximum load. There is no harm to use a shelf or drawer according to the shapes and size of food to be frozen.

• Thawing frozen food in fridge

compartment will both provide energy saving and preserve the food quality.

Reccomendations for freshfood compartment

* OPTIONAL

• Please do not let any foodstuff to

come to contact with the temperature sensor in freshfood compartment. In order to maintain freshfood compartment at ideal storage temperature, the sensor must not be blocked by fodstuffs.

• Do not place hot foodstuff in your

appliance.

3 Installation

C Please remember that the

manufacturer shall not be held liable if the information given in the instruction manual is not observed.

Points to be considered when re-transporting your refrigerator

1. Your refrigerator must be emptied and cleaned prior to any transportation.

2. Shelves, accessories, crisper and etc. in your refrigerator must be fastened securely by adhesive tape against any jolt before repackaging.

3. Packaging must be tied with thick tapes and strong ropes and the rules of transportation printed on the package must be followed.

C Always remember...

Every recycled material is an indispensable source for the nature and for our national resources.

If you wish to contribute to recycling the packaging materials, you can get further information from the environmental bodies or local authorities.

Before operating your refrigerator

Before starting to use your refrigerator

check the following:

1. Is the interior of the refrigerator dry and can the air circulate freely in the rear of it?

2. Clean the interior of the refrigerator as recommended in the “Maintenance and cleaning” section.

3. Insert the 2 plastic wedges onto the rear ventilation as illustrated in the following figure. Unscrew the existing ones and use the screws given in the same bag of wedges. Plastic wedges will provide the required distance between your refrigerator and the wall in order to allow the air circulation.

4. Plug the refrigerator into the wall outlet. When the door is open the respective interior light will come on.

5. You will hear a noise as the compressor starts up. The liquid and gases sealed within the refrigeration system may also give rise to noise, even if the compressor is not running and this is quite normal.

6. Front edges of the refrigerator may feel warm. This is normal. These areas are designed to be warm to avoid condensation.

Electric connection

Connect your refrigerator to a grounded socket which is being protected by a fuse with the appropriate capacity.

Important:

B The connection must be in

compliance with national regulations.

B The power cable plug must be easily

accessible after installation.

The specified voltage must be equal

to your mains voltage.

B Extension cables and multiway plugs

must not be used for connection.

B A damaged power cable must be

replaced by a qualified electrician.

B The appliance must not be operated

before it is repaired! There is danger of electric shock!

Disposing of the packaging

The packing materials may be

dangerous for children. Keep the

packing materials out of the reach of children or dispose them of by classifying them in accordance with the waste instructions. Do not dispose them of along with the normal household waste.

The packing of your refrigerator is produced from recyclable materials.

Disposing of your old refrigerator

Dispose of your old machine without giving any harm to the environment.

A You may consult your authorized

dealer or waste collection center of your municipality about the disposal

of your refrigerator.

Before disposing of your refrigerator,

cut out the electric plug and, if there are any locks on the door, make them inoperable in order to protect children against any danger.

Placing and Installation

Caution: Never plug the refrigerator

into the wall outlet during installation. Otherwise, risk of death or serious injury may arise.

A If the entrance door of the room

where the refrigerator will be installed is not wide enough for the refrigerator to pass through, than call the authorised service to have them remove the doors of your refrigerator and pass it sideways through the door.

1. Install your refrigerator to a place that allows ease of use.

2. Keep your refrigerator away from

heat sources, humid places and direct sunlight.

3. There must be appropriate air ventilation around your refrigerator in order to achieve an efficient operation. If the refrigerator is to be placed in a recess in the wall, there must be at least 5 cm distance with the ceiling and at least 5 cm with the wall.

If the floor is covered with a carpet, your product must be elevated 2.5 cm from the floor.

4. Place your refrigerator on an even

floor surface to prevent jolts.

5. Do not keep your refrigerator in

ambient temperatures under 10°C.

Floor balance adjustment

If your refrigerator is unbalanced; You can balance your refrigerator by

turning the front legs of it as illustrated

in the figure. (See Figure A) The corner

where the leg exists is lowered when you turn in the direction of black arrow and raised when you turn in the opposite direction. Taking help from someone to slightly lift the refrigerator will facilitate this process.

2. Loosen the three screws of the hinges of the lower door, which you wish to escalate, with the help of a screwdriver as shown in the figure

below. (Do not remove completely) (See Figure C)

(C)

(A)

1 2 3

(B)

Door height adjustment

In case there is a problem with the alignment of the doors with respect to each other, they may be re-aligned vertically in the order given below. Ensure that door shelves are empty when adjusting the door height.

1. Remove the lower ventilation cover

by unscrewing its screws as shown in

the figure below. (See Figure B)

• If the freezer compartment door is

lower than the fridge compartment door, bring them to the same level by turning the turning the elevation screw on the freezer compartment side in the direction of arrow using a M6 Allen wrench as illustrated in Figure D.

• If the freezer compartment door is

higher than the fridge compartment door, bring them to the same level by turning the elevation screw on

the freezer compartment side in the reverse direction of arrow using a M6 Allen wrench as illustrated in Figure D.

After bringing the doors to the same level by elevating the front part with the aid of the elevation screws,ensure the doors of the refrigerator shall close properly. If the doors do not close properly, this might adversely affect the efficiency of the refrigerator.

(D)

Adjusting the gap between the upper door

C You can adjust the gap between

the fridge compartment doors as illustrated in the figures.

Door shelves should be empty when adjusting the door height.

switch off the refrigerator power before removing hinge covers and this situation should be made to take care.

C Using a screwdriver, remove the

screw of upper hinge cover of the door you want to adjust.

C Adjust the door appropriately as

you desire by loosing the screws.

Because of being wires in the hinge cover of the freezer door,

Fix the door you have adjusted by tightening the screws without changing the position of the door.

C Replace the hinge cover and fix

with the screw.

Installing Water Filter

(in some models)

Installation Requirements

Two different water sources may be connected to the refrigerator for water supply: the mains cold water supply and water in a jug.

A pump should be used for jug water usage.

Check that the parts stated below are supplied with your appliance.

3. 5 meter long water pipe (1/4 inch in

diameter)

4. Cold mains water valve with mesh

filter (Tap Adapter)

5. Water Filter to be fitted to the bracket

inside the fridge compartment.

1. Union for connection of the water pipe to the rear of the appliance

2. 3 pieces of pipe clips (In case

required to secure the water pipe)

C Note: Since the following parts are

not required in use with a jug, they may not be found in the product you purchased.

Water connection to the refrigerator Please follow the instructions below.

Connection of the Water Pipe to the Refrigerator

1. After installing the union onto the water pipe, insert the water pipe to the refrigerator inlet valve by pressing downwards firmly.

2. Fix union as seen in the opposite figure, by squeezing by hand on the refrigerator inlet valve.

(a- Water Pipe, b-Union, c-Valve)

C Note 1: You should not need to

tighten the union with a tool to achieve water tight assembly. In case of a leak use a spanner or a pair of pliers to tighten the union.

To fit the water filter follow the instructions below referring to figures supplied:

1. Press ice cancel button on the

display. (Figure 1)

2. Remove the filter cover in the fridge

compartment by pulling it forward.

(Figure 2)

3. Take out the water filter by-pass cover by rotating it downwards.

(Figure 3-4)

A Warning: Make sure that the “Ice

off” mode is active before taking out the by-pass cover.

Note: It is normal that a few drops of

water drip after the cover has been taken out.

4. Remove the lid on top of the water

filter to place it as shown in the figure

and turn upwards to lock it. (Figure 5)

5. Press ice cancel button on the display again to exit from this mode.

Water filter should be replaced every 6 months. The water filter must be removed as shown in the figure when it is going to be replaced or when it will no longer be used and by-pass cover must be attached. It must be made sure that Ice Off mode is active before taking it out.

A Warning: Water filter cleans some

foreign particles in the water. It does not purify water from microorganisms.

A Warning: Ice Off button must

always be pressed during replacement of the water filter or installing the bypass cover.

Connection of Water Hose to the Jug

(in some models)

To connect water to the refrigerator from a jug, a pump is needed. Follow

C Note: You may refer to the user

manual of the pump while making the water connection.

Connection of the Water Pipe to the Cold Water Mains Line

(in some models)

If you want to use your refrigerator by connecting it to the cold water mains line,

you will have to connect a standard 1/2” valve connection fitting to the cold water supply in your house. In case

the instructions below after connecting one end of the water pipe coming out of the pump to the refrigerator as described on the previous page.

1. Finish the connection by pushing the other end of the water pipe into the water pipe inlet of the pump as shown in the figure.

2. Put and fix the pump hose into the jug as shown in the figure.

3. After completing the connection, plug in and run the pump.

To provide an efficient operation of the

pump, wait for 2-3 minutes after starting the pump.

this valve is not present or in case you are not sure, consult a qualified plumber.

1. Separate the union from the tap

adaptor. (Figure A)

2. Install the tap adaptor to 1/2” valve

fitting as shown in the figure. (Figure B)

3. After inserting the water pipe to the union, install it to the tap adaptor and insert to the tap as shown in the

figure. (Figure C)

4. Tighten the union manually. In case of a leak use a spanner or a pair of pliers to tighten the union.

A Warning: Secure the water pipe

to suitable points by means of the pipe clips supplied to avoid any damage or displacement or accidental disconnection.

A Warning: After turning on the water

valve, make sure that there is no leakage at both connection points of the water pipe. In case of a leak, turn off the valve immediately and tighten all joints again using a spanner or a pair of pliers.

A Warning: Make sure that standard

1/2" valve fitting fed by cold mains water supply is available and is turned off fully.

Note -1: There is no need to use water

filter in case a jug is used.

Note -2: Pump must be used when jug

will be used.

Prior to first use of Ice/Water Dispenser

C Water mains pressure must not be

below 1 bar.

C Water mains pressure must not be

over 8 bars.

C The first 10 glasses of water should

not be consumed.

C 12 hours must pass to obtain ice

from the Ice Dispenser for the first time. If there is not enough ice in the ice dispenser, ice may not be obtained from ice dispenser.

C Pumps must be used in case the

supply water pressure drops below 1 bar or if a jug is going to be used.

C Water system of the refrigerator

must be connected to the cold water line. It must not be connected to hot water line.

C No water may be obtained in the

initial startup of the refrigerator. This is caused by the air in the system. To discharge air from the system, press Dispenser latch for periods of 1 minute until water comes from the Dispenser. Water flow may be irregular in the beginning. Irregular water flow will be normalized after the air in the system is discharged.

C At the initial startup of the

refrigerator approx.12 hours must pass before cold water can be obtained.

C Approximately the first 30 cubes

of ice to be obtained from the Ice Dispenser must not be used.

C Always use the water filter when a

jug is not being used.

C Water mains pressure must be

between 1-8 bars for the operation of Ice/Water Dispenser smoothly. For

this, check that 1 glass of water (100

cc) can be filled in 10 seconds.

4 Preparation

C Your refrigerator should be installed at

least 30 cm away from heat sources such as hobs, ovens, central heater and stoves and at least 5 cm away from electrical ovens and should not be located under direct sunlight.

C The ambient temperature of

the room where you install your refrigerator should at least be 10°C. Operating your refrigerator under cooler conditions than this is not recommended with regard to its efficiency.

C Please make sure that the interior

of your refrigerator is cleaned thoroughly.

C If two refrigerators are to be installed

side by side, there should be at least 2 cm distance between them.

C When you operate your refrigerator

for the first time, please observe the following instructions during the initial six hours.

- The door should not be opened

frequently.

- It must be operated empty without

any food in it.

- Do not unplug your refrigerator. If

a power failure occurs out of your control, please see the warnings in

the “Recommended solutions for

the problems” section.

C Original packaging and foam

materials should be kept for future transportations or moving.

5 Using your refrigerator

11 10

-24 °C

-22 °C

-20 °C

-18 °C

1. Fridge Set button

2. Vacation mode button

3. Quick fridge button

4. Key lock button

5. Ice Off button

6. Water Dispenser Lights

7. Ice / Wate selection button

8. Water Dispenser light button

9. Filter Reset button

10. Auto Eco button

11. Quick freeze button

12. Freezer Set button

13. Economy mode indicator

14. High humidity indicator

15. Quick cool indicator

29 1413

26 25 24 23 19

1528

20212227

16. Fridge temperature setting indicator

17. High temperature/error warning indicator

18. Fridge door open indicator

19. Key Lock indicator

20. Vacation mode indicator

21. Water indicator

22. No ice indicator

23. Crash Ice indicator

24. Cube Ice indicator

25. Auto Eco indicator

26. Filter reset indicator

27. Freezer door open indicator

28. Freezer Compartment Temperature Setting indicator

29. Fast Freeze indicator

30. Ioniser indicator

OPTIONAL

2 °C 4 °C 6 °C

8 °C

C Figures that take place in this instruction manual are schematic and may not

correspond exactly with your product. If the subject parts are not included in the product you have purchased, then it is valid for other models.

Freezer Compartment Adjustment

-15°C 4°C This is the normal recommended

-18,-21 or -24°C 4°C These settings are recommended

Fresh Freeze 4°C Use this when you wish to freeze

-15°C or colder 2°C If you think that your fridge

-15°C or colder Quick Cool You can use it when your fridge

Setting the fridge compartment temperature

Fridge compartment temperature can be set at one of the following temperatures:

8,6,4 and 2°C Press the Fridge Set button to change.

The temperature will decrease by 2°C. Every time you press the button, the temperature will go down and then

return to the highest setting. Release

at the desired temperature and the new set temperature will be stored.

If you think that your food is colder than you desire, you can adjust the temperature setting of fridge compartment to 6 or 8.

Setting the freezer compartment temperature

Freezer temperature can be set at one of the following temperatures : -15 /

-18 / -21 / -24 and -24°C

Fridge Compartment Adjustment

Explanations

setting.

when the ambient temperature exceeds 30°C.

your food or make ice in a short time. Your refrigerator will return to its previous mode when the process is over.

compartment is not cold enough because of the hot conditions or frequent opening and closing of the door.

compartment is overloaded or if you wish to cool down your food rapidly.

Press the Freezer Set button to change. The temperature will decrease by 2°C. Every time you press the button, the temperature will go down and then return to the highest setting.

Release at the desired temperature

and the new set temperature will be stored.

Fresh Freeze Function

When you press “Fresh Freeze” button, the compressor will run for about 14 hours. Fresh Freeze indicator will glow.To cancel this function press Fresh Freeze button again. Fresh Freeze indicator will turn off and return to its normal settings. Fresh Freeze will cancel itself automatically after about 12 hours if you do not cancel it.

If you want to freeze large amounts of fresh food, press the Fresh Freeze button 14 hours before putting the food into the freezer compartment.

Quick Cool Function

When you press Quick Cool button, the temperature of the compartment will be colder than the adjusted values. This function can be used for food placed in the fridge compartment and required to be cooled down rapidly.

After pressing the Quick Cool button, Quick Cool indicator will glow.To cancel this function press Quick Cool button again. Quick Cool indicator will turn off and return to its normal settings. Quick Cool function will cancel itself automatically in case you do not cancel it.

Vacation Button

In case the fridge compartment will not be used for a long time, the usage of the fridge compartment may be cancelled by pressing on the Vacation

Button. By this way, the refrigerator

may operate more economically. Press

on Vacation Button for 3 seconds

to activate this function. When this function is active, the door of the fridge compartment must be kept closed and no food must be left in the fridge compartment.

Auto Eco Button (Special Economy function)

When “Auto Eco” button is pressed, Auto Economy Function will be activated. If the door of the fridge compartment is kept closed for a long time when this function is selected, the fridge compartment will switch to a more economic operation mode to save electricity automatically. When the Auto Eco button is pressed again, this function is deactivated.

Ioniser

The ioniser helps purify the air in the fridge and is carried out automatically

Key Lock Button

The key lock is activated when this button is pressed for 3 seconds and all buttons and the dispenser latch will not work. If you want to deactivite key lock press again for 3 seconds.

Water Dispenser Illumination

When the Light button is pressed, the water dispenser lamp will light up and it will go off when the button is pressed again. This illumination will also light up when the water dispenser latch is pressed, and it will go off a short while after the latch is released.

Water/Ice Type Selection

With Dispenser Selection button, either one of “water”, “ice cube” or “crushed ice” options is selected.

Ice/Water Dispenser

With its three different functions, the dispenser efficiently meets your cold water, cube ice and crushed ice needs without having to open the door of the refrigerator. It is a continuous cold water and ice source without adding water. User friendly control panel provides the following dispensing functions:

Note:

• Water or ice can be dispensed for a

maximum of 90 seconds at each use.

• When the freezer door is open, the

dispenser will not work.

Ice Cube Crushed Ice Cold Water

Using the Ice Dispenser

Please note, first ice cubes will not be ready before 12 hours after switching on the appliance.

In case you do not need ice, such as during winter or in case you are on vacation, select the ice off function.

C Ice device produces approximately

110 cubes of ice in 24 hours and this amount may change according to the frequency of opening of doors, refrigerator settings and power outage. Produced ice may be obtained from the dispenser as cube ice or crushed ice.

It is normal to get crushed ice from the dispenser in a longer time than in getting the ice cubes and also flowing of some crushed ice before the ice cubes drop if crushed ice option had been selected before selecting ice cube option.

C If the ice dispenser hasn’t been

used for a long time or after a power cut the ice may form clumps or if the ice has taken on a change in smell or taste then the ice must be disposed of and the icebox cleaned thoroughly.

Warnings

C No ice must be added to the ice

dispenser compartment. This may adversely affect the ice supply or crushing the ice.

A It is normal to have a couple of ice

cubes stuck together in the icebank.

A Moving parts such as blades in

a housing at the ice outlet of the dispenser must not be touched to

avoid injury.

A Never use sharp objects to break

the ice in the icebox. This may cause damage on the icebox.

A Food stuff should never be placed

into the icebox for quick cooling purposes.

A When the icebox is to be removed for

any reason, first of all Ice Off Button

must be pressed.

Ice Off

To stop ice formation, Ice Off button is pressed. When Ice Off is selected, no water will be taken into the Icematic. However, already existing ice can be taken from the dispenser. To restart ice formation, Ice Off button must be pressed again.

Warning: If you do not use the ice dispenser, do not forget to put ice duct cover into the ring inside of the freezer door. (See. Your Refrigerator

section)

FILTER Reset Button:

Water filter should be replaced every six months. Filter reset indicator lits if water filter needs to be changed Press

filter Reset Button for 3 seconds to

remove filter reset indicator warning.

Using the water spring

Warnings

It is normal for the first few glasses of water taken from the dispenser to be warm.

In cases where the water dispenser has not been used frequently, sufficient amount of water must be drained from the dispenser to get fresh water.

Spillage Tray

Water drops that drip during use, accumulates in the spillage tray. You can remove spillage tray by pulling it to yourself or pressing on its edge

(depending on the model). You can

remove the water with a sponge or a soft cloth.

Sliding Body Shelves

Sliding body shelves can be pulled by slightly lifting up from the front and moved back and forth. They come to a stop point when pulled towards front to allow you reach the foods placed at the back of the shelf; when it is pulled after slightly lifted upwards at the second stop point, the body shelf will be released.

The shelf should be hold tightly from the bottom as well in order to prevent it from tipping over. The body shelf is placed on the rails at the sides of the refrigerator body by bringing it to one lower or one upper level.

The body shelf should be pushed backwards to seat it completely.

Blue light

Foodstuff stored in the crispers that are enlightened with a blue light continue their photosynthesis by means of the wavelength effect of blue light and thus, preserve their freshness and increase their vitamin content.

Ion:

Air is ionized by means of the ionizer system in the fridge compartment air duct. Thanks to this system, air-borne bacteria and particles that cause odour are removed.

Egg tray

You can install the egg holder to the desired door or body shelf.

Never store the egg holder in the

freezer compartment

Crisper humidity control sliders

Crisper of your refrigerator is designed especially fresh to keep your vegetables freshly without loosing their humidity. Cold air circulates basically around the crisper and the amount of the cold air passing through the crisper is controlled by the sliders on the front side of the crisper cover.

You can adjust the humidity control sliders to a suitable position according to the humidity and cooling condition of your food in the crisper.

If you want your food in the crisper to cool more, open the holes of the humidity control sliders and if you want them to cool less and keep their humidity for a longer time, close the holes.

Fresh Freeze Compartment

This compartment freezes your food quickly and preserves their tastes and nutritional values.

Recommendations for preservation of frozen food

• Prepacked commercially frozen

food should be stored in accordance with the frozen food manufacturer's instructions for a ( 4 star) frozen food storage compartment.

• To ensure that the high quality

achieved by the frozen food manufacturer and the food retailer is maintained, the following should be remembered:

1.Put packets in the freezer as quickly as possible after purchase.

2.Ensure that contents are labelled and dated.

3.Do not exceed "Use By", "Best Before" dates on the packaging.

If there is a power failure do not open the freezer door. Even if the power failure lasts up to the time

specified on Type Label (inside left of

the refrigerator), frozen food will not be affected. In case the failure lasts longer, the food must be checked and when necessary, must be consumed immediately or must be frozen after cooked.

Defrosting

The fridge and freezer compartments defrost automatically.

Replacing the Interior Light Bulb

Should the light fail to work, proceed as follows:

1. Switch off at the socket outlet and pull out the mains plug.

Remove all shelves and drawers for

easy access.

2. Illumination illumination cover in fridge section is opened by pressing by hand; first release one side and then the other by pressing on the sides as shown in the figures.

3. First check that the bulb has not worked loose by ensuring that it is screwed securely in the holder.

Reinsert the plug and switch on. If the

bulb works, reinstall the light cover by inserting the rear lug and pushing up to locate the front two lugs.

4.If the light still fails to work, switch off at the socket outlet and pull out

the mains plug. Replace the bulb with a new 15 watt (max) screw cap E14 (SES) bulb.

5.Carefully dispose of the burnt-out light bulb immediately.

Replacement light bulb can easily be

obtained from a good local electrical or DIY store.

EN27EN

6 Maintenance and cleaning

A Never use gasoline, benzene or

similar substances for cleaning purposes.

B We recommend that you unplug the

appliance before cleaning.

B Never use any sharp abrasive

instrument, soap, household cleaner, detergent and wax polish for cleaning.

C Use lukewarm water to clean the

cabinet of your refrigerator and wipe it dry.

C Use a damp cloth wrung out in

a solution of one teaspoon of bicarbonate of soda to one pint of water to clean the interior and wipe it dry.

B Make sure that no water enters the

lamp housing and other electrical items.

B If your refrigerator is not going to be

used for a long period of time, unplug the power cable, remove all food, clean it and leave the door ajar.

C Check door seals regularly to ensure

they are clean and free from food particles.

A To remove door racks, remove all the

contents and then simply push the door rack upwards from the base.

Protection of plastic surfaces

Do not put the liquid oils or oil-cooked

meals in your refrigerator in unsealed containers as they damage the plastic surfaces of your refrigerator. In case of spilling or smearing oil on the plastic surfaces, clean and rinse the relevant part of the surface at once with warm water.

Chiller compartment

If you wish to use the storage container under the shelf as the Chiller compartment, the storage container under the shelf should be placed as shown in the picture.

Chiller compartments enable the foods to be frozen become ready for freezing. You can also use these compartments to store your food at a temperature a few degrees below the fridge compartment.

You can increase the inner volume of your refrigerator by removing any of the chiller compartments. To do this, pull the compartment towards yourself; the compartment will lean against the stopper and stop. This compartment will be released when you lift it about 1 cm and pull it towards yourself.

Icebox and Water Dispenser

Follow the procedure and warnings below to clean the icebox:

A Remove the Icebox by lifting first

and then pulling towards yourself as shown in the diagram.

A Empty the ice in the Icebox if any.

To take out the stuck ice, use objects that are not sharp to avoid any damage on the Icebox.

A Pay attention that the inside of

the Icebox is not wet/damp before placing it back to its housing.

A If you want to get ice from the ice

dispenser after placing the Icebox back to its housing and closing the freezer door, exit from Ice Off mode by pressing the Ice Off key again.

A Do not touch moving parts like

the knife in the Icebox.

C Leave the Water Reservoir

empty when you are not going to use for a long time

+ 362 hidden pages