Beko DS 145010, DS145010B, DS145010S, DS145010P, DS145000S User manual [EN,FR,AR]

DS 145010	DS145000S	RDSE450K20W
DS145010B	RDSE450K11W	RDSE 450 K11S
DS145010S	RDSE450K11B	RDSE450K11P
DS145010P	RDSE 450 K11M	DS145010WG
EN FR AR

Please read this user manual first!

Dear Customer,

We hope that your product, which has been produced in modern plants and checked under the most meticulous quality control procedures, will provide you an effective service.

Therefore, read this entire user manual carefully before using the product and keep it as a reference. If you handover the product to someone else, give the user manual as well.

The user manual will help you use the product in a fast and safe way.

•Read the manual before installing and operating the product.

•Make sure you read the safety instructions.

•Keep the manual in an easily accessible place as you may need it later.

•Read the other documents given with the product.

Remember that this user manual is also applicable for several other models. Differences between models will be identified in the manual.

Explanation of symbols

Throughout this user manual the following symbols are used:

CImportant information or useful tips.

AWarning against dangerous conditions for life and property. BWarning against electric voltage.

CONTENTS

1 Your refrigerator	3
2 Important Safety
Warnings	4
Intended use......................................	4
General safety...................................	4
For products with a ...........................	7
water dispenser;.................................	7
Child safety........................................	7
Compliance with WEEE Directive and
Disposing of the Waste Product: .......	7
Package information..........................	7
HC warning........................................	8
Things to be done for energy saving...	8
3 Installation	9
Points to be paid attention to when the
relocation of the refrigerator................	9
Electrical connection..........................	9
Disposing of the packaging..............	10
Disposing of your old refrigerator......	10
Placing and Installation.....................	10
Adjusting the legs.............................	11
Changing the illumination lamp ........	11
Reversing the doors.........................	12
Reversing the doors.........................	13
Reversing the doors.........................	14
Reversing the doors.........................	15

4 Preparation

16

5 Using your refrigerator 17

Thermostat setting button................	17
Defrost.............................................	17
Making ice........................................	18
Stopping your product.....................	18
Crisper humidity control sliders.........	19
Turbo Cooling Fan............................	19
Using the rotary crisper (in some
models)............................................	20

6 Maintenance and	21
cleaning
Protection of plastic surfaces	.......... 21
7.	22
Troubleshooting

2 EN

1 Your refrigerator

151

*2

4*3
5	*12
*6
	13

166 *12

6

7

8

9

*10

11

	1.	Ice cube tray	9.	Salad crisper
	2.	Freezer shelf	10.	Adjustable legs
	3.	Interior light	11.	Door shelf
	4.	Thermostat knob	12.	Egg tray
	5.	Fridge compartment shelves	13.	Bottle shelf
	6.	Defrost water collection channel	14.Key
		- Drain tube	15.Freezer compartment
	7.	Crisper humidity controls
			16.Fridge compartment
	8.	Crisper cover
			* OPTIONAL

*

*14

CFigures that take place in this instruction manual are schematic and may not correspond exactly with your product. If the subject parts are not included in the product you have purchased, then it is valid for other models.

3 EN

		Important Safety Warnings
	2
	Please review the following		• For products with a freezer
			compartment; Do not put
	information. Failure to observe
			bottled and canned liquid
	this information may cause
			beverages in the freezer
	injuries or material damage.
			compartment. Otherwise, these
	Otherwise, all warranty and
			may burst.
	reliability commitments will
			• Do not touch frozen food by
	become invalid.
			hand; they may stick to your
	Original spare parts will be
			hand.
	provided for 10 years, following
			• Unplug your refrigerator before
	the product purchasing date.		cleaning or defrosting.
	Intended use
			• Vapor and vaporized cleaning
	This product is intended to be
			materials should never be
	used
			used in cleaning and defrosting
	• indoors and in closed areas
			processes of your refrigerator.
	such as homes;
			In such cases, the vapor may
	• in closed working environments
			get in contact with the electrical
	such as stores and offices;
			parts and cause short circuit or
	• in closed accommodation areas
			electric shock.
	such as farm houses, hotels,
			• Never use the parts on your
	pensions.
			refrigerator such as the door as
	• It should not be used outdoors.
			a means of support or step.
	General safety
			• Do not use electrical devices
	• When you want to dispose/
			inside the refrigerator.
	scrap the product, we
			• Do not damage the parts,
	recommend you to consult the
	authorized service in order to		where the refrigerant is
			circulating, with drilling or
	learn the required information
			cutting tools. The refrigerant
	and authorized bodies.
			that might blow out when the
	• Consult your authorized
			gas channels of the evaporator,
	service for all your questions
			pipe extensions or surface
	and problems related to the
			coatings are punctured causes
	refrigerator. Do not intervene or
			skin irritations and eye injuries.
	let someone intervene to the
			• Do not cover or block the
	refrigerator without notifying the
	authorised services.		ventilation holes on your
			refrigerator with any material.
	• For products with a freezer
			• Electrical devices must be
	compartment; Do not eat
			repaired by only authorised
	cone ice cream and ice cubes
			persons. Repairs performed by
	immediately after you take them
			incompetent persons create a
	out of the freezer compartment!
			risk for the user.
	(This may cause frostbite in your
	mouth.)
	4		EN

•In case of any failure or during a maintenance or repair work, disconnect your refrigerator’s mains supply by either turning off the relevant fuse or unplugging your appliance.

•Do not pull by the cable when pulling off the plug.

•Ensure highly alcoholic beverages are stored securely with the lid fastened and placed upright.

•Never store spray cans containing flammable and explosive substances in the refrigerator.

•Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

•This product is not intended to be used by persons with physical, sensory or mental disorders or unlearned or

inexperienced people (including children) unless they are attended by a person who

will be responsible for their safety or who will instruct them accordingly for use of the product

•Do not operate a damaged refrigerator. Consult with the service agent if you have any concerns.

•Electrical safety of your refrigerator shall be guaranteed only if the earth system in

your house complies with standards.

•Exposing the product to rain, snow, sun and wind is

dangerous with respect to electrical safety.

•Contact authorized service when there is a power cable damage to avoid danger.

•Never plug the refrigerator into the wall outlet during installation. Otherwise, risk of death or serious injury may arise.

•This refrigerator is intended for only storing food items. It must not be used for any other purpose.

•Label of technical specifications is located on the left wall inside the refrigerator.

•Never connect your refrigerator to electricity-saving systems; they may damage the refrigerator.

•If there is a blue light on the refrigerator, do not look at the blue light with optical tools.

•For manually controlled refrigerators, wait for at least 5 minutes to start the refrigerator after power failure.

•This operation manual should be handed in to the new owner of the product when it is given to others.

•Avoid causing damage on power cable when transporting the refrigerator. Bending cable may cause fire. Never place heavy objects on power cable. Do not touch the plug with wet hands when plugging the product

5 EN

•Do not plug the refrigerator if the wall outlet is loose.

•Water should not be sprayed on inner or outer parts of the product for safety purposes.

•Do not spray substances containing inflammable gases such as propane gas near the refrigerator to avoid fire and explosion risk.

•Never place containers filled with water on top of the refrigerator; in the event of spillages, this may cause electric shock or fire.

•Do not overload the refrigerator with food. If overloaded, the food items may fall down

and hurt you and damage refrigerator when you open the door.

•Never place objects on top of the refrigerator; otherwise, these objects may fall down when you open or close the refrigerator’s door.

•As they require a precise temperature, vaccines, heat-sensitive medicine and scientific materials and etc. should not be kept in the refrigerator.

•If not to be used for a long time, refrigerator should be unplugged. A possible problem

in power cable may cause fire.

•The plug’s tip should be cleaned regularly with a dry cloth; otherwise, it may cause fire.

•Refrigerator may move if adjustable legs are not properly secured on the floor. Properly securing adjustable legs on the floor can prevent the refrigerator to move.

•When carrying the refrigerator, do not hold it from door handle. Otherwise, it may be snapped.

•When you have to place your product next to another refrigerator or freezer, the distance between devices should be at least 8cm.

Otherwise, adjacent side walls may be humidified.

•The product shall never be used while the compartment which is located at the top or back of your product and in which electronic boards are available (electronic board box cover) (1) is open.

1

1

6 EN

For products with a water dispenser;

•Pressure for cold water inlet shall be maximum 90 psi (6.2 bar). If your water pressure exceeds 80 psi (5.5 bar), use a pressure limiting valve in your mains system. If you do not know how to check your water pressure, ask for the help of a professional plumber.

•If there is risk of water hammer effect in your installation, always use a water hammer prevention equipment in your installation. Consult Professional plumbers is you are not

sure that there is no water hammer effect in your installation.

•Do not install on the hot water inlet. Take precautions against of the risk of freezing of the hoses. Water temperature operating interval shall be 33°F (0.6°C) minimum and 100°F (38°C) maximum.

•Use only potable water.

Child safety

•If the door has a lock, the key should be kept away from reach of children.

•Children must be supervised to prevent them from tampering with the product.

Compliance with WEEE Directive and Disposing of the Waste Product:

This product complies

with EU WEEE Directive (2012/19/EU). This product

bears a classification symbol for waste electrical and electronic equipment

(WEEE).

This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities

to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children’s safety, cut the power cable and break the locking mechanism of the door, if any, so

that it will be non-functional before disposing of the product.

Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

Do not forget...

Any recycled substance is an indispensable matter for nature and our national asset wealth.

7 EN

If you want to contribute to the re-evaluation of the packaging materials, you can consult to your environmentalist organizations or the municipalities where you are located.

HC warning

If your product's cooling system contains R600a:

This gas is flammable. Therefore, pay attention to not damaging the cooling system and piping during usage and transportation. In the event of damage, keep your product away from potential fire sources that can cause the product catch a fire and ventilate the room in which the unit is placed.

Ignore this warning if your product's cooling system contains R134a.

Type of gas used in the product is stated in the type label which is on the left wall inside the refrigerator.

Never throw the product in fire for disposal.

Things to be done for energy saving

•Do not leave the doors of your refrigerator open for a long time.

•Do not put hot food or drinks in your refrigerator.

•Do not overload your refrigerator so that the air circulation inside of it is not prevented.

•Do not install your refrigerator under direct sunlight or near heat emitting appliances such as ovens, dishwashers or radiators. Keep your refrigerator at least 30cm away from heat emitting sources and at least 5cm from electrical ovens.

•Pay attention to keep your food in closed containers.

•For products with a freezer compartment; You can store maximum amount of food items in the freezer when you remove the shelf or drawer of the freezer. Energy consumption value stated for your refrigerator has been determined

by removing freezer shelf or drawer and under maximum load. There is no harm to use a shelf or drawer

according to the shapes and size of food to be frozen.

•Thawing frozen food in fridge compartment will both provide energy saving and preserve the food quality.

8 EN

3 Installation

B In case the information which are given in the user manual are not taken into account, manufacturer will not assume

any liability for this.

Points to be paid attention to when the relocation of the refrigerator

1.Your refrigerator should be unplugged.Before transportation of your refrigerator, it should be emptied and cleaned.

2.Before it is re-packaged, shelves, accessories, crisper, etc. inside your refrigerator should be fixed with adhesive tape and secured against impacts. Package should be bound with a thick tape or sound ropes and the transportation rules on the package should be strictly observed.

3.Original packaging and foam materials should be kept for future transportations or moving.

Before you start the refrigerator,

Check the following before you start to use your refrigerator:

1.Attach 2 plastic wedges as illustrated below. Plastic wedges are intended to keep the distance which will ensure the air circulation between your refrigerator and the wall. (The picture is drawn up as a representation and it is not identical with your product.)

2.Clean the interior of the refrigerator as recommended in the “Maintenance and cleaning” section.

3.Connect the plug of the refrigerator to the wall socket. When the fridge door is opened, fridge internal lamp will turn on.

4.When the compressor starts to operate, a sound will be heard. The liquid and gases sealed within the refrigeration system may also give rise to noise, even if the compressor is not running and this is quite normal.

5.Front edges of the refrigerator may feel warm. This is normal. These areas are designed to be warm to avoid condensation.

Electrical connection

Connect your product to a grounded socket which is being protected by a fuse with the appropriate capacity.

Important:

The connection must be in compliance with national regulations.

•The power plug must be easily accessible after installation.

•Electrical safety of your refrigerator shall be guaranteed only if the earth system in your house complies with standards.

•The voltage stated on the label located at left inner side of your product should be equal to your network voltage.

•Extension cables and multi plugs must not be used for connection.

9 EN

B A damaged power cable must be replaced by a qualified electrician.

B Product must not be operated before it is repaired! There is the risk of

electric shock!

Disposing of the packaging

The packing materials may be dangerous for children. Keep the packing materials out of the reach of children or dispose of them by

classifying them in accordance with the waste instructions stated by your local authorities. Do not throw away with regular house waste, throw away on packaging pick up spots designated by the local authorities.

The packing of your refrigerator is produced from recyclable materials.

Disposing of your old refrigerator

Dispose of your old refrigerator without giving any harm to the environment.

•You may consult your authorized dealer or waste collection center of your municipality about the disposal of your refrigerator.

Before disposing of your refrigerator, cut out the electric plug and, if there are any locks on the door, make them inoperable in order to protect children against any danger.

Placing and Installation

A If the entrance door of the room where the refrigerator will be installed is not wide enough for the refrigerator to pass through, then call the authorized service to have them remove the doors of your refrigerator and pass it sideways through the door.

1.Install your refrigerator to a place that allows ease of use.

2.Keep your refrigerator away from heat sources, humid places and direct sunlight.

3.There must be appropriate air ventilation around your refrigerator in order to achieve an efficient operation. If the refrigerator is to be placed in a recess in the wall, there must be at least 5 cm distance with the ceiling and at least 5 cm with the wall. Do not place your product on the materials such as rug or carpet.

4.Place your refrigerator on an even floor surface to prevent jolts.

10 EN

Adjusting the legs

If your refrigerator is unbalanced;

You can balance your refrigerator by turning its front legs as illustrated in the figure. The corner where the leg exists is lowered when you turn in the direction of black arrow and raised when you turn in the opposite

direction. Taking help from someone to slightly lift the refrigerator will facilitate this process.

Changing the illumination lamp

To change the Bulb/LED used for illumination of your refrigerator, call your AuthorisedService.

The lamp(s) used in this appliance is not suitable for household room

illumination. The intended purpose of this lamp is to assist the user to place foodstuffs in the refrigerator/freezer

in a safe and comfortable way.The lamps used in this appliance have to withstand extreme physical conditions such as temperatures below -20 °C.

(only chest and upright freezer)

11 EN

Reversing the doors

Proceed in numerical order.

4 5

4 2

7	6	1

10

10

	11
12	13

45°

3

8 9

			14
	18	19
		17
	180°	19	22
			24
	23	21
			24
			20

16 15

12 EN

Reversing the doors

Proceed in numerical order.

10

4

5

4

	2
	1
6	12

7

10

10

11

13

12

45 °

3

9 8

14

19

18

180°	17
	1	22

24

23

2

24

2

16

15

13 EN

Reversing the doors

Proceed in numerical order.

10

4

5

10

42

	7		1	11
		6
			12	13

45°

3

8 9

14

	18	19
		17
	180°	19	22
			24

23	21
	24
	20

16 15

14 EN

Reversing the doors

Proceed in numerical order.

4 5

4 2

7	6	1

10

10

	11
12	13

45°

3

8 9

14

18	19
	17

180° 19 22

23

21

20

16 15

15 EN

4	Preparation
•	Your cooler/freezer should be	not thaw thanks to its Advanced
installed at least 30 cm away from		Electronic Temperature Control
heat sources such as hobs, ovens,		System. For the first installation, the
central heater and stoves and at least		product should NOT be placed under
5 cm away from electrical ovens and		low ambient temperatures. This is
should not be located under direct		because the freezer cannot go down
sunlight.		to standard operation temperature.
• Please make sure that the interior		When reaching continuous operation,
of your cooler/freezer is cleaned		the product can be moved to
thoroughly.		another place. Thus, later you can
• If two coolers are to be installed side		place your product in the garage
by side, there should be at least 2 cm		or an unheated room without the
distance between them.		concern of causing frozen food to
• When you operate your cooler/freezer		get rotten. However, it is likely that
for the first time, please observe the		above mentioned low temperatures
following instructions during the initial		may cause the freezing of the food in
six hours.		the fridge compartment; thus, please
• Its door should not be opened		consume the food items in the fridge
frequently.		in a controlled way as needed. When
• It must be operated empty without		ambient temperature goes back
placing any food in it.		to normal, you may change button
• Do not unplug your cooler/freezer.		setting according to your need.
If a power failure occurs out of your		• If the ambient temperature is below
control, please see the warnings in		0°C, the food in fridge compartment
the “Recommended solutions for the		will freeze. Therefore, we recommend
problems” section.		not using the fridge compartment
• The baskets/drawers that are		in such low ambient temperatures.
provided with the chill compartment		You may continue to use the freezer
must always be in use for low energy		compartment as usual.
consumption and for better storage		• In some models, the instrument panel
conditions.		automatically turns off 5 minutes
• Food contact with the temperature		after the door has closed. It will
sensor in the freezer compartment		be reactivated when the door has
may increase energy consumption of		opened or pressed on any key.
the appliance. Thus any contact with		• Due to temperature change as a
the sensor(s) must be avoided.		result of opening/closing the product
• This product has been designed to		door during operation, condensation
function at ambient temperatures		on the door/body shelves and the
up to 43 °C (90 SDgrF). Even if the		glass containers is normal.
ambient temperature falls to -15
°C, frozen food in the freezer does

16 EN

	5 Using your refrigerator
	Thermostat setting button	Defrost
		Fridge compartment performs full-
		automatic defrosting. Water resulting
		from the defrosting passes from the
		water collection groove and flows
		into the evaporator through the drain
		pipe and evaporates here by itself.
		• Deep freezer compartment does not
		perform automatic defrosting in order
		to prevent decaying of the frozen
		food.
		•Check regularly to see if the drain
	The interior temperature of your	pipe is clogged or not and clear
		it with the stick in the hole when
	refrigerator changes for the following
		necessary.
	reasons;

	• Seasonal temperatures,
	• Frequent opening of the door and
	leaving the door open for long
	periods,
	• Food put into the refrigerator
	without cooling down to the room
	temperature,
	• The location of the refrigerator in the
	room (e.g. exposing to sunlight).
	• You may adjust the varying interior
	temperature due to such reasons
	by using the thermostat. Numbers	• Frost formation in the freezer
	around the thermostat button
		compartment must be defrosted
	indicates the cooling degrees.
		every 6 months. It is recommended
	• If the ambient temperature is higher
		to defrost the ice when the deep
	than 32°C, turn the thermostat
		freezer compartment is not filled too
	button to maximum position.
		much or is empty.
	• If the ambient temperature is lower
		• To do this, wrap the frozen food
	than 25°C, turn the thermostat
		by paper and keep them in the
	button to minimum position.
		coolest place possible or in another
		refrigerator if available.

17 EN

•Stop your refrigerator by means of the temperature setting button or unplug the power cord from the outlet. You can place a container filled with hot water into the freezer compartment or leave the door of the freezer compartment open in order to hasten the defrosting.

•Remove the water that accumulates

in the lower container of the freezer compartment with an absorbent cloth or sponge.

•Dry the freezer compartment completely and return the temperature setting button to its previous position.

•Operate your refrigerator for 2 hours while it is empty and its doors are closed before replacing your food into the deep freezer.

Stopping your product

If your thermostat is equipped with “0” position:

- Your product will stop operating when you turn the thermostat button to “0” (zero) position. Your product will not start unless to you turn the thermostat button to position “1” or one of the other positions again.

If your thermostat is equipped with “min” position:

- Unplug your product to stop it.

Making ice

*optional

Fill the ice container with water and place it into the freezer compartment. Your ice will be ready approximately in two hours.

You can remove the ice in the ice container by removing it from the freezer and twisting it.

18 EN

Crisper humidity control sliders

Using the crisper humidity control sliders

Crisper of your refrigerator is designed specially to keep your vegetables fresh without loosing their humidity. Cold air circulates basically around the crisper and the amount of the cold air passing through the crisper is controlled by the sliders on the front side of the crisper cover.

You can adjust the humidity control sliders to a suitable position according to the humidity and cooling condition of your food in the crisper.

If you want your food in the crisper to cool more, open the holes of the humidity control sliders and if you want them to cool less and keep their humidity for a longer time, close the holes.

Turbo Cooling Fan

“Turbo cooling fan is designed to ensure homogenous distribution and circulation of the cold air inside your refrigerator. Operation time of the turbo cooling fan may vary depending on the properties of your product. While the turbo fan works only with the compressor in some products, the control system determines its operation time in some products

in accordance with the cooling requirement. This situation is explained on a separate warning and information label attached on the refrigerator in products equipped with turbo fans running under different conditions than the compressor.”

* OPTIONAL

19 EN

Using the rotary crisper (in some models)

The crisper of your refrigerator which opens with a rotating movement is designed specially to provide ease of usage and allow you to store more vegetables and fruits (large volume) you buy during large shopping.

When you grab and pull the handle on the lower left hand side of the crisper, it will rotate from left to right and open easily. The separator in the crisper will allow you to separate the vegetables and fruits according to their types and prevent them from crushing.

20 EN

6 Maintenance and cleaning

ANever use gasoline, benzene or similar substances for cleaning purposes.

BWe recommend that you unplug the appliance before cleaning.

BNever use any sharp abrasive instrument, soap, household cleaner, detergent and wax polish for cleaning.

B For non-No Frost products, water drops and frosting up to a

fingerbreadth occur on the rear wall of the Fridge compartment. Do not clean it; never apply oil or similar agents on it.

BOnly use slightly damp microfiber cloths to clean the outer surface of the product. Sponges and other types of cleaning cloths may scratch the surface.

CUse lukewarm water to clean the cabinet of your refrigerator and wipe it dry.

CUse a damp cloth wrung out in a solution of one teaspoon of

bicarbonate of soda to one pint of water to clean the interior and wipe it dry.

BMake sure that no water enters the lamp housing and other electrical items.

BIf your refrigerator is not going to be used for a long period of time, unplug the power cable, remove all food, clean it and leave the door ajar.

CCheck door seals regularly to ensure they are clean and free from food particles.

ATo remove door racks, remove all the contents and then simply push the door rack upwards from the base.

ANever use cleaning agents or water that contain chlorine to clean the outer surfaces and chromium coated parts of the product. Chlorine causes corrosion on such metal surfaces.

ADo not use sharp, abrasive tools, soap, household cleaning agents, detergents, kerosene, fuel oil, varnish etc. to prevent removal and deformation of the prints on the plastic part. Use lukewarm water and a soft cloth for cleaning and then

wipe it dry.

Protection of plastic surfaces

CDo not put the liquid oils or oil-cooked meals in your refrigerator in unsealed containers as they damage the plastic surfaces of your refrigerator. In case of spilling or smearing oil on the plastic surfaces, clean and rinse the relevant part of the surface at once with warm water.

21 EN

7. Troubleshooting

Check this list before contacting the service. Doing so will save you time and money. This list includes frequent complaints that are not related to faulty workmanship or materials. Certain features mentioned herein may not apply to your product.

The refrigerator is not working.

•The power plug is not fully settled. >>>

Plug it in to settle completely into the socket.

•The fuse connected to the socket powering the product or the main fuse is blown. >>> Check the fuses.

Condensation on the side wall of the cooler compartment (MULTI ZONE, COOL, CONTROL and FLEXI ZONE).

•The door is opened too frequently >>>

Take care not to open the product’s door too frequently.

•The environment is too humid. >>>

Do not install the product in humid environments.

•Foods containing liquids are kept in unsealed holders. >>> Keep the foods containing liquids in sealed holders.

•The product’s door is left open. >>> Do not keep the product’s door open for long periods.

•The thermostat is set to too low temperature. >>> Set the thermostat to appropriate temperature.

Compressor is not working.

•In case of sudden power failure or pulling the power plug off and putting back on, the gas pressure in the product’s cooling system is not balanced, which triggers the compressor thermic safeguard. The product will restart after approximately 6 minutes. If the product does not restart after this period, contact the service.

•Defrosting is active. >>> This is normal for a fully-automatic defrosting product. The defrosting is carried out periodically.

•The product is not plugged in. >>>

Make sure the power cord is plugged in.

•The temperature setting is incorrect.

>>> Select the appropriate temperature setting.

•The power is out. >>> The product will continue to operate normally once the power is restored.

The refrigerator’s operating noise is increasing while in use.

•The product’s operating performance may vary depending on the ambient temperature variations. This is normal and not a malfunction.

The refrigerator runs too often or for too long.

•The new product may be larger than the previous one. Larger products will run for longer periods.

•The room temperature may be high.

>>> The product will normally run

for long periods in higher room temperature.

•The product may have been recently plugged in or a new food item is placed inside. >>> The product will take longer to reach the set temperature when recently plugged in or a new food item is placed inside. This is normal.

•Large quantities of hot food may have been recently placed into the product.

>>> Do not place hot food into the product.

•The doors were opened frequently or kept open for long periods. >>> The warm air moving inside will cause the product to run longer. Do not open the doors too frequently.

22 EN