This section provides the safety
instructions necessary to prevent
the risk of injury and material
damage. Failure to observe these
instructions will invalidate all
types of product warranty.
• If the product will not be used
for a while, unplug the product
and remove any food inside.
• Do not use the product when
the compartment with circuit
cards located on the upper back
part of the product (electrical
1.1. General safety
• This product should not be
card box cover) (1) is open.
used by persons with physical,
sensory and mental disabilities,
without sufficient knowledge
and experience or by children.
The device can only be
used by such persons under
supervision and instruction of
a person responsible for their
safety. Children should not be
allowed to play with this device.
• In case of malfunction, unplug
the device.
• After unplugging, wait at least
5 minutes before plugging in
again.
• Unplug the product when not in
use.
• Do not touch the plug with wet
hands! Do not pull the cable to
plug off, always hold the plug.
• Wipe the power plug’s tip with
a dry cloth before plugging in.
• Do not plug in the refrigerator if
the socket is loose.
• Unplug the product during
installation, maintenance,
cleaning and repair.
Refrigerator / User Guide
• Do not use steam or steamed
cleaning materials for cleaning
the refrigerator and melting the
ice inside. Steam may contact
the electrified areas and cause
short circuit or electric shock!
• Do not wash the product by
spraying or pouring water on it!
Danger of electric shock!
• In case of malfunction, do not
use the product, as it may
cause electric shock. Contact
the authorized service before
doing anything.
3 / 37 EN
1
1
Safety and environment instructions
• Plug the product into an
earthed socket. Earthing
must be done by a qualified
electrician.
• If the product has LED type
lighting, contact the authorized
service for replacing or in case
of any problem.
• Do not touch frozen food with
wet hands! It may adhere to
your hands!
• Do not place liquids in bottles
and cans into the freezer
compartment. They may burst
out!
• Place liquids in upright position
after tightly closing the lid.
• Do not spray flammable
substances near the product,
as it may burn or explode.
• Do not keep flammable
materials and products with
flammable gas (sprays, etc.) in
the refrigerator.
• Do not place containers
holding liquids on top of the
product. Splashing water on
an electrified part may cause
electric shock and risk of fire.
• Exposing the product to rain,
snow, sunlight and wind will
cause electrical danger. When
relocating the product, do not
pull by holding the door handle.
The handle may come off.
• Take care to avoid trapping any
part of your hands or body in
any of the moving parts inside
the product.
• Do not step or lean on the door,
drawers and similar parts of
the refrigerator. This will cause
the product to fall down and
cause damage to the parts.
• Take care not to trap the power
cable.
1.1.1 HC warning
If the product comprises a cooling
system using R600a gas, take
care to avoid damaging the
cooling system and its pipe while
using and moving the product.
This gas is flammable. If the
cooling system is damaged, keep
the product away from sources
of fire and ventilate the room
immediately.
The label on the inner
left side indicates the
C
type of gas used in the
product.
4 / 37 EN
Refrigerator / User Guide
Safety and environment instructions
1.1.2 For models with
water dispenser
• Pressure for cold water inlet
shall be maximum 90 psi (6.2
bar). If your water pressure
exceeds 80 psi (5.5 bar), use a
pressure limiting valve in your
mains system. If you do not
know how to check your water
pressure, ask for the help of a
professional plumber.
• If there is risk of water hammer
effect in your installation,
always use a water hammer
prevention equipment in
your installation. Consult
Professional plumbers is you
are not sure that there is no
water hammer effect in your
installation.
• Do not install on the hot water
inlet. Take precautions against
of the risk of freezing of the
hoses. Water temperature
operating interval shall be 33°F
(0.6°C) minimum and 100°F
(38°C) maximum.
• Use drinking water only.
1.2. Intended use
• This product is designed for
home use. It is not intended for
commercial use.
• The product should be used to
store food and beverages only.
Refrigerator / User Guide
• Do not keep sensitive
products requiring controlled
temperatures (vaccines,
heat sensitive medication,
medical supplies, etc.) in the
refrigerator.
• The manufacturer assumes no
responsibility for any damage
due to misuse or mishandling.
• The product’s bench life is
10 years. The spare parts
necessary for the product to
function will be available for
this period.
1.3. Child safety
• Keep packaging materials out
of children’s reach.
• Do not allow the children to
play with the product.
• If the product’s door comprises
a lock, keep the key out of
children’s reach.
1.4. Compliance with WEEE Directive
and Disposing of the Waste Product
This product complies with EU WEEE
Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and
electronic equipment (WEEE).
This product has been manufactured
with high quality parts and materials
which can be reused and are suitable
for recycling. Do not dispose of the
waste product with normal domestic
and other wastes at the end of its
service life. Take it to the collection
center for the recycling of electrical and
electronic equipment. Please consult your local
authorities to learn about these collection
centers.
5 / 37 EN
Safety and environment instructions
1.5. Compliance with RoHS Directive
• This product complies with EU WEEE Directive
(2011/65/EU). It does not contain harmful and
prohibited materials specified in the Directive.
1.6. Package information
• Packaging materials of the product are
manufactured from recyclable materials in
accordance with our National Environment
Regulations. Do not dispose of the packaging
materials together with the domestic or other
wastes. Take them to the packaging material
collection points designated by the local
authorities.
6 / 37 EN
Refrigerator / User Guide
2 Refrigerator
2
3
*4
5
*6
1
*7
*11
*16
*17
*18
12
13
14
15
13
*8
10
*9
1- Freezer compartment
2- Cooler compartment
3- Fan
4- Butter-cheese compartment
5- Glass shelves
6- Cooler compartment door shelves
7- Minibar accessory
8- Water tank
9- Bottle shelf
*Optional: Figures in this user guide are schematic and may not be exactly match your product. If your
product does not comprise the relevant parts, the information pertains to other models.
C
Refrigerator / User Guide
7 / 37 EN
2 Refrigerator
13
*14
12
10
2
3
5
8
9
*4
*6
*7
1
C
11
*Optional: Figures in this user guide are schematic and may not be exactly match your product. If your
product does not comprise the relevant parts, the information pertains to other models.
8 / 37 EN
11
Refrigerator / User Guide
3 Installation
3.1. Right place for installation
Contact the Authorized Service for the product's
installation. To ready the product for installation,
see the information in the user guide and make
sure the electric and water utilities are as required.
If not, call an electrician and plumber to arrange
the utilities as necessary.
WARNING: The manufacturer assumes
no responsibility for any damage caused
B
B
A
•Placetheproductonaflatsurfacetoavoid
vibration.
•Placetheproductatleast30cmawayfromthe
heater, stove and similar sources of heat and at
least 5 cm away from electric ovens.
function efficiently. If the product will be placed
in an alcove, remember to leave at least 5 cm
distance between the product and the ceiling
and the walls.
must be unplugged during installation.
Failure to do so may result in death or
serious injuries!
WARNING: : If the door span is too
narrow for the product to pass, remove
the door and turn the product sideways; if
this does not work, contact the authorized
service.
3.2. Attaching the plastic wedges
Use the plastic wedges in the provided with
the product to provide sufficient space for air
circulation between the product and the wall.
1.
To attach the wedges, remove the screws on the
product and use the screws provided with the wedges.
2.
Attach 2 plastic wedges on the ventilation cover
shown as j in the figure.
Refrigerator / User Guide
9 / 37 EN
Installation
3.3. Adjusting the stands
If the product is not in balanced position, adjust the
front adjustable stands by rotating right or left.
3.4. Power connection
WARNING: Do not use extension or multi
A
B
C
• Our firm will not assume responsibility for any
• The power cable plug must be easily
• Connect the refrigerator to an earthed socket
• Do not use multi-group plug with or without
sockets in power connection.
WARNING: Damaged power cable must
be replaced by Authorized Service.
When placing two coolers in adjacent
position, leave at least 4 cm distance
between the two units.
damages due to usage without earthing and
power connection in compliance with national
regulations.
accessible after installation.
with 220-240V/50 Hz voltage. The plug must
comprise a 10-16A fuse.
extension cable between the wall socket and
the refrigerator.
3.5. Water connection
(Optional)
WARNING: Unplug the product and
the water pump (if available) during
A
The product’s water mains, filter and carboy
connections must be rendered by authorizer
service. The product can be connected to a carboy
or directly to the water mains, depending on the
model. To establish the connection, the water hose
must first be connected to the product.
Check to see the following parts are supplied with
your product’s model:
1
3
1. Connector (1 piece): Used to attach the water
2. Hose clip (3 pieces): Used to fix the water
3. Water hose (1 piece, 5 meter diameter 1/4
4. Faucet adapter (1 piece): Comprises a porous
5. Water filter (1 piece *Optional): Used to
connection.
2
4
hose to the rear of the product.
hose on the wall.
inches): Used for the water connection.
filter, used for connection to the cold water
mains.
connect the mains water to the product. Water
filter is not required if carboy connection is
available.
*5
10 / 37 EN
Refrigerator / User Guide
Installation
3.6. Connecting water
hose to the product
To connect the water hose to the product,
follow the instructions below.
1. Remove the connector on the hose nozzle
adaptor in the back of the product and run the
hose through the connector.
3.7. Connecting to water mains
(Optional)
To use the product by connecting to the cold water
mains, a standard 1/2” valve connector must be
installed to the cold water mains in your home. If
the connector is not available or if you are unsure,
consult a qualified plumber.
1. Detach the connector (1) from the faucet
adaptor (2).
2. Push the water hose down tightly and connect
to the hose nozzle adaptor.
3. Tighten the connector manually to fix on the
hose nozzle adaptor. You may also tighten the
connector using a pipe wrench or pliers.
3
2. Connect the faucet adaptor to the water mains
valve.
3. Attach the connector around the water hose.
2
23
1
1
4. Connect the other end of the hose to the
water mains (See Section 3.7) or, to use
carboy, to the water pump (See Section 3.8).
Refrigerator / User Guide
11 / 37 EN
Installation
4. Attach the connector into the faucet adaptor
and tighten by hand / tool.
5. To avoid damaging, shifting or accidentally
disconnecting the hose, use the clips provided
to fix the water hose appropriately.
2. Connect the other end of the water hose to
the water pump by pushing the hose into the
pump’s hose inlet.
3. Place and fasten the pump hose inside the
carboy.
WARNING: After turning the faucet
on, make sure there is no water leak on
A
either end of the water hose. In case of
leakage, turn the valve off and tighten
all connections using a pipe wrench or
pliers.
3.8. For products using water carboy
(Optional)
To use a carboy for the product’s water
connection, the water pump recommended by the
authorized service must be used.
1. Connect one end of the water hose provided
with the pump to the product (see 3.6) and
follow the instructions below.
4. Once the connection is established, plug in
and start the water pump.
Please wait 2-3 minutes after starting
the pump to achieve the desired
C
C
C
efficiency.
See also the pump’s user guide for
water connection.
When using carboy, water filter is not
required.
3.9 Water filter
(Optional)
The product may have internal or external filter,
depending on the model. To attach the water filter,
follow the instructions below.
12 / 37 EN
Refrigerator / User Guide
Installation
3.9.1.Fixing external filter
on the wall (Optional)
WARNING: Do not fix the filter on the
A
Check to see the following parts are supplied with
your product’s model:
product.
5
4
6
4. Attach the water hose extending from the top
of the filter to the product’s water connection
adaptor, (see 3.6.)
1
1. Connector (1 piece): Used to attach the water
hose to the rear of the product.
2. Faucet adapter (1 piece): Used for connection
to the cold water mains.
3. Porous filter (1 piece)
4. Hose clip (3 pieces): Used to fix the water
hose on the wall.
5. Filter connecting apparatus (2 pieces): Used to
fix the filter on the wall.
6. Water filter (1 piece): Used to connect the
product to the water mains. Water filter is not
necessary when using carboy connection.
1. Connect the faucet adaptor to the water mains
valve.
2. Determine the location to fix the external filter.
Fix the filter’s connecting apparatus (5) on the
wall.
3. Attach the filter in upright position on the filter
connecting apparatus, as indicated on the
label. (6)
3
2
After the connection is established, it should look
like the figure below.
Refrigerator / User Guide
13 / 37 EN
Installation
3.9.2.Internal filter
The internal filter provided with the product is not
installed upon delivery; please follow the instructions
below to install the filter.
Water line:
1. “Ice Off” indicator must be active while
installing the filter. Switch the ON-OFF
indicator using the “Ice” button on the screen.
2. Remove the vegetable bin (a) to access the
water filter.
Carboy line:
C
Do not use the first 10 glasses of
water after connecting the filter.
14 / 37 EN
a
Refrigerator / User Guide
Installation
3. Remove the water filter by-pass cover by
pulling.
A few drops of water may flow out
after removing the cover; this is
C
4. Place the water filter cover into the
mechanism and push to lock in place.
normal.
5. Push the “Ice” button on the screen again to
cancel the “Ice Off” mode.
The water filter will clear certain foreign
particles in the water. It will not clear the
C
C
Refrigerator / User Guide
microorganisms in the water.
See section 5.2 for activating the filter
replacing period.
15 / 37 EN
4 Preparation
4.1. What to do for energy saving
mehmet
Connecting the product to electronic
energy-saving systems is harmful, as it
A
• Do not keep the refrigerator doors open for
• Do not place hot food or beverages into the
• Do not overfill the refrigerator; blocking the
• The energy consumption value specified for
• Depending on the product’s features;
• The baskets/drawers that are provided with the
• Food contact with the temperature sensor in
• Make sure the foods are not in contact with
may damage the product.
long periods.
refrigerator.
internal air flow will reduce cooling capacity.
the refrigerator was measured with the freezer
compartment’s upper shelf removed, other
shelves and the lowest drawers in place and
under maximum load. The top glass shelf can
be used, depending on the shape and size of
food to be frozen.
defrosting frozen foods in the cooler
compartment will ensure energy saving and
preserve food quality.
chill compartment must always be in use for
low energy consumption and for better storage
conditions.
the freezer compartment may increase energy
consumption of the appliance. Thus any
contact with the sensor(s) must be avoided.
the cooler compartment temperature sensor
described below.
4.2. First Use
Before using your refrigerator, make sure the
necessary preparations are made in line with
the instructions in “Safety and environment
instructions” and “Installation” sections.
• Keep the product running with no food
inside for 6 and do not open the door, unless
absolutely necessary.
A sound will be heard when the
compressor is engaged. It is normal to
C
C
C
hear sound even when the compressor is
inactive, due to the compressed liquids
and gasses in the cooling system.
It is normal for the front edges of the
refrigerator to be warm. These areas are
designed to warm up in order to prevent
condensation.
In some models, the instrument panel
automatically turns off 5 minutes after
the door has closed. It will be reactivated
when the door has opened or pressed on
any key.
16 / 37 EN
Refrigerator / User Guide
5 Using the product
5.1. Indicator panel
Indicator panels may vary depending on the model of your product.
Audial and visual functions of the indicator panel will assist in using the refrigerator.
1
8
2
3
9
76
1.
Cooler compartment indicator
2.
Error status indicator
3.
Temperature indicator
4.
Vacation function button
5.
Temperature adjustment button
6.
Compartment selection button
7.
Cooler compartment indicator
8.
Economy mode indicator
9.
Vacation function indicator
*optional
45
*Optional: The figures in this user guide are intended as drafts and may not perfectly match your
product. If your product does not comprise the relevant parts, the information pertains to other models.
C
Refrigerator / User Guide
17 / 37 EN
Using the product
1. Cooler compartment indicator
The cooler compartment light will turn on when
adjusting the cooler compartment temperature.
2. Error status indicator
This sensor will activate if the refrigerator is not
cooling adequately or in case of sensor fault. When
this indicator is active, the freezer compartment
temperature indicator will display "E" and the
cooler compartment temperature indicator will
display "1, 2, 3..." etc. numbers. The numbers on
the indicator serve to inform the service personnel
about the fault.
3. Temperature indicator
Indicates the temperature of the freezer and cooler
compartments.
4.Vacation function button
This indicates that the vacation function is
activated. When the vacation function is activated
no cooling is performed in the fridge compartment
however the freezer compartment will continue
to be actively cooled. “—“ is displayed on the
fridge compartment temperature indicator. It is not
suitable to keep food in the fridge compartment
when this function is activated. Other
compartments will continued to be cooled as per
their set temperature. To cancel this function press
the vacation function button again.”
5. Temperature adjustment button
Respective compartment's temperature varies in
-24°C..... -18°C and 8°C...1°C ranges.
6. Compartment selection button
Use the refrigerator compartment selection
button to toggle between the cooler and freezer
compartments.
7. Cooler compartment indicator
The freezer compartment light will turn on when
adjusting the cooler compartment temperature.
8. Economy mode indicator
Indicates the refrigerator is running on energysaving mode. This indicator will be active when
the temperature in the freezer compartment is set
to -18°C.
9.Vacation function indicator
Indicates the vacation function is active.
18 / 37 EN
Refrigerator / User Guide
Using the product
2
1
11
1. Economic use
2- High temperature / fault alert
3. Energy saving function (display off)
4- Rapid cooling
5- Vacation function
6- Cooler compartment temperature setting
7. Energy saving (display off) /Alarm off warning
8- Keypad lock
9- Eco-fuzzy
10- Freezer compartment temperature setting
11- Rapid freezing
3
7.2 7.1
8
910
4
56
*Optional: The figures in this user guide are intended as drafts and may not perfectly match
your product. If your product does not comprise the relevant parts, the information pertains
C
Refrigerator / User Guide
to other models.
19 / 37 EN
Using the product
1. Economic use
This sign will light up when the freezer
compartment is set to -18°C', the most
economical setting. () Economic use indicator
will turn off when rapid cooling or rapid freezing
function is selected.
2. Power failure/High temperature / error
warning indicator
This indicator () will light up in case of
temperature faults or fault alerts. If you see this
indicator is lit up, please see the "recommended
solutions for problems" section in this guide.
This indicator illuminates during power failure, high
temperature failures and error warnings. During
sustained power failures, the highest temperature
that the freezer compartment reaches will flash on
the digital display. After checking the food located
in the freezer compartment press the alarm off
button to clear the warning.
Please refer to “remedies advised for
troubleshooting” section on your manual if you
observe that this indicator is illuminated.
3. Energy saving function (display off)
If the product doors are kept closed for a long time
energy saving function is automatically activated
and energy saving symbol is illuminated. When
energy saving function is activated, all symbols
on the display other than energy saving symbol
will turn off. When the Energy Saving function is
activated, if any button is pressed or the door is
opened, energy saving function will be canceled
and the symbols on display will return to normal.
Energy saving function is activated during delivery
from factory and cannot be canceled.
4. Rapid cooling
When the rapid cooling function is turned on, the rapid cool indicator will light up () and the cooler compartment temperature indicator will display the value 1.
Push the Rapid cool button again to cancel this function. The Rapid cool indicator will turn off and return to
normal setting. The rapid cooling function will be automatically cancelled after 1 hour, unless cancelled by
the user. Too cool a large amount of fresh food, press
the rapid cool button before placing the food in the cooler compartment.
5. Vacation function
To activate the Vacation function, , press the quick
fridge button for 3 seconds; this will activate the
vacation mode indicator (). When the Vacation
function is active, the cooler compartment
temperature indicator displays the inscription
"- -" and no cooling process will be active in
the cooling compartment. This function is not
suitable to keep food in the cooler compartment.
Other compartments will remain cooled with the
respective temperature set for each compartment.
Push the vacation function button again to cancel
this function.
6. Cooler compartment temperature setting
After pressing the button, the cooler compartment
temperature can be set to 8,7,6,5,4,3,2 and 1
respectively.()
7. 1 Energy saving (display off)
Pressing this button () will light up the energysaving sign () and the Energy-saving function
will activate. Activating the energy-saving function
will turn off all other signs on the display. When
the energy-saving function is active, pressing any
button or opening the door will deactivate the
energy-saving function and the display signals will
return to normal. Pressing this button () again
will turn off the energy-saving sign and deactivate
the energy-saving function.
20 / 37 EN
Refrigerator / User Guide
Using the product
7.2 Alarm off warning
In case of power failure/high temperature alarm,
after checking the food located in the freezer
compartment press the alarm off button to clear
the warning.
8. Keypad lock
Press the display off button, simultaneously for 3
seconds. The keypad lock sign will light up and the
keypad lock will be activated; the buttons will be
inactive when the Keypad lock is activated. Press
the Display off button again simultaneously for 3
seconds. The keypad lock sign will turn off and
the keypad lock mode will be disengaged. Press
the Display off button to prevent changingthe
refrigerator’s tempeture settings.
9. Eco-fuzzy
To activate the eco-fuzzy function, press and hold
the eco-fuzzy button for 1 second. When this
function is active, the freezer will switch to the
economic mode after at least 6 hours and the
economic use indicator will light up. To deactivate
the ( ) eco-fuzzy function, press and hold the
eco-fuzzy function button for 3 seconds.
The indicator will light up after 6 hours when the
eco-fuzzy function is active.
10. Freezer compartment temperature setting
The temperature in the freezer compartment is
adjustable. Pressing the button will enable the
freezer compartment temperature to be set at
-18,-19, -20, -21, -22, -23 and -24.
11. Rapid freezing
For rapid freezing, press the button; this will
activate the rapid freezing indicator ().
When the rapid freezing function is turned on, the
rapid freeze indicator will light up and the freezer
compartment temperature indicator will display
the value -27. Press the Rapid freeze button (
) again to cancel this function. The Rapid freeze
indicator will turn off and return to normal setting.
The rapid freezing function will be automatically
cancelled after 24 hours, unless cancelled by the
user. To freeze a large amount of fresh food, press
the rapid freeze button before placing the food in
the freezer compartment.
(*) Optional: The figures in this user guide are intended as drafts and may not perfectly
match your product. If your product does not comprise the relevant parts, the information
pertains to other models.
22 / 37 EN
Refrigerator / User Guide
Using the product
1. Freezer compartment temperature setting
Pressing the button () will enable the freezer
compartment temperature to be set at -18,-19,20,-21 ,-22,-23,-24,-18...
2. Economy mode
Indicates the refrigerator is running on energysaving mode. This indicator will be active when the
freezer compartment temperature is set at -18 or
the energy-saving cooling is engaged by eco-extra
function. ()
3.Energy saving function (display off)
If the product doors are kept closed for a long time
energy saving function is automatically activated
and energy saving symbol is illuminated. When
energy saving function is activated, all symbols
on the display other than energy saving symbol
will turn off. When the Energy Saving function is
activated, if any button is pressed or the door is
opened, energy saving function will be canceled
and the symbols on display will return to normal.
Energy saving function is activated during delivery
from factory and cannot be canceled.
4. Power failure/High temperature / error
warning indicator
This indicator () will light up in case of
temperature faults or fault alerts. If you see this
indicator is lit up, please see the "recommended
solutions for problems" section in this guide.
This indicator illuminates during power failure, high
temperature failures and error warnings. During
sustained power failures, the highest temperature
that the freezer compartment reaches will flash on
the digital display. After checking the food located
in the freezer compartment press the alarm off
button to clear the warning.
Please refer to "remedies advised for
troubleshooting" section on your manual if you
observe that this indicator is illuminated.
5. Cooler compartment temperature setting
After pressing the button (), the cooler
compartment temperature can be set to
8,7,6,5,4,3,2.. respectively.
6. Rapid cooling
For rapid cooling , press the button; this will
activate the rapid cooling indicator ().
Press this button again to deactivate this function.
Use this function when placing fresh foods into
the cooler compartment or to rapidly cool the
food items. When this function is activated, the
refrigerator will be engaged for 1 hour.
7. Vacation function
When the Vacation function ( ) is active, the
cooler compartment temperature indicator displays
the inscription "- -" and no cooling process
will be active in the cooling compartment. This
function is not suitable to keep food in the cooler
compartment. Other compartments will remain
cooled with the respective temperature set for
each compartment.
Press the vacation function button again to cancel
this function. ()
8. Keypad lock / Keypad lock / filter replacing
alert cancellation
Press keypad lock button ( ) to activate the
keypad lock. You may also use this function to
prevent changing the refrigerator's temperature
settings. The refrigerator's filter must be replaced
every 6 months. If you follow the instructions in
the section 5.2, the refrigerator will automatically
calculate the remaining period and the filter
replacing alert indicator () will light up when
filter expires.
Press and hold the button () for 3 seconds to
turn off the filter alert light.
9. Water, fragmented ice, ice cubes selection
Navigate the water (), ice cube () and
fragmented ice () selections using the button.
The active indicator will remain lit.
10. Ice making on/off
Press the button () to cancel () or
activate () ice-making.
11.1 Display on/off
Press the button () to cancel (XX) or
activate () display on/off.
Refrigerator / User Guide
23 / 37 EN
Using the product
11.2 Alarm off warning
In case of power failure/high temperature alarm,
after checking the food located in the freezer
compartment press the alarm off button to clear
the warning.
12. Autoeco
Press the auto eco button (), for 3 seconds to
activate this function. If the door remains closed
for a long time when this function is activated, the
cooler section will switch to economic mode. Press
the button again to deactivate this function.
The indicator will light up after 6 hours when the
auto eco function is active. ( )
13. Rapid freezing
Press the button () for rapid freezing. Press the
button again to deactivate the function.
24 / 37 EN
Refrigerator / User Guide
Loading...
+ 58 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.