Beko DVTC 60 W User Manual

Vented Time Dryer

DVTC 60 W

Read this manual prior to initial operation of the product!

Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference.

This User Manual will

• Help you use your machine in a fast and safe way.

• Read the User Manual before installing and starting your product.

• In particular, follow the instructions related to safety.

• Keep this User Manual within easy reach for future reference.

• Please read all additional documents supplied with your product. Remember that this User Manual is also applicable for several other models.

Explanation of symbols

Throughout this User Manual the following symbols are used:

A Important safety information. Warning for hazardous situations with regard to life

and property.

B Caution; Warning for supply voltage.

Caution; Warning for fire hazard.

Caution; Warning for hot surfaces.

Read the instructions.

C Useful information. Important information or useful hints about usage.

This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under

the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

2960310279/171209.1531

TABLE OF CONTENTS

1 Your Dryer 4

Overview .......................................4

2 Important safety information 6

General safety ............................... 6

Intended use ................................. 7

Children’s safety ............................ 7

3 Installation 8

Appropriate installation location ..... 8

Under counter installation .............. 8

Ventilation hose and connection (for products equipped with an outlet

vent) .............................................. 8

Adjusting feet ................................ 9

First use ........................................ 9

Disposing of packaging material .... 9

Transportation of the machine ....... 9

Disposing of the old machine .........9

4 Electrical Connection 10

Electrical requirements ................. 10

Fitting a different plug ................. 10

5 Initial preparations for drying 11

Things to be done for energy

saving: ......................................... 11

Laundry suitable for drying in the

machine ......................................11

Laundry unsuitable for drying in the

machine ......................................11

Preparing laundry for drying ......... 12

Correct load capacity .................. 12

Loading .......................................12

Programme selection and

consumption table ....................... 15

Auxiliary function .......................... 16

Warning indicators ....................... 16

Starting the Programme .............. 16

Timer follow-up indicator .............16

Changing the programme after the

programme has started ............... 16

Child-proof lock ........................... 16

Ending the programme through

cancelling .................................... 17

End of programme ...................... 17

7 Quick instructions for daily use

8 Maintenance and cleaning 19

Fluff filter ..................................... 19

9 Solution suggestions for problems 20

10 Door Reversal 21

11 Guarantee 22

What is covered? ......................... 22

What is not covered? ................... 22

Important notes ...........................22

12 Service 23

6 Selecting a Programme and Operating Your Machine 13

Control panel ............................... 13

Preparing the machine ................. 14

Timer programme selection ......... 14

Main programmes ....................... 14

1 Your Dryer

Overview

1- Rating label

2- Control Panel

3- Fluff filter

4- Adjustable Feet

5- Power Cord

Technical Specifications

EN 2

Height (adjustable) 85.0 cm

Width 59.5 cm

Depth 54 cm

Capacity (max.) 6 kg

Weight (net) 31 kg

Voltage

See rating labelRated power input

Model code

Type label is located behind the loading door.

Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly. Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the appliance, values may vary.

2 Important safety information

TThis section includes safety information

that will help protection from risks of personal injuries or materialistic damages. Failure to follow these instructions shall cause any warranty and reliability commitment to become void.

General safety

• Never place the machine on a carpet-

covered floor, otherwise, lack of airflow beneath the machine may cause electrical parts to overheat. This will cause problems with your machine.

• If the power cable or mains plug is

damaged, you must call Authorised Service Agent for repair.

• The product should not be plugged

in during installation, maintenance and repair works. Such works should always be made by the technical

service. Manufacturer shall not be held

responsible for damages arising from processes carried out by unauthorised persons.

• Connect the product to a grounded

outlet protected by a fuse of suitable capacity as stated in the technical specifications table.

• Operate your product at temperatures

between +5°C and +35°C.

• Do not use electrical devices in the

product.

• Do not connect the air exit of the

product to the chimney holes which are used for the exhaust fumes of the devices operating with gas or other types of fuel.

• You must provide enough ventilation

in order to prevent gases exiting from devices operating with other types of fuels including the naked flame from accumulating in the room due to the back fire effect.

• Always clean the lint filter before or

after each loading.

• Never operate your dryer without the

lint filter installed.

• Do not allow fibre, dust and dirt

accumulation around the exhaust exit and at adjacent areas.

• Power cable plug must be within easy

reach after installation.

• Do not use extension cords, multi-

• Do not make any changes on the plug

• Items cleaned or washed with gasoil/

• Do not dry items cleaned with

• Do not dry unwashed items in the

• Items soiled with cooking oils,

• Garments or pillows bolstered with

• Do not use fabric softeners and

• This product must be earthed.

• Do not install the product behind a

plugs or adaptors to connect the dryer to power supply in order to decrease the risk of electric shock.

supplied with the product. If it is not

compatible with the socket, have a qualified electrician change the socket with a suitable one.

fuel oil, dry-laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should not be dried in the product since they emit flammable or explosive vapor.

industrial chemicals in the dryer.

dryer.

acetone, alcohol, fuel oil, kerosene, stain remover, turpentine, paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer.

rubber foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads should not be dried in the dryer.

anti-static products unless they are recommended by the manufacturers of the fabric softener or the product.

Grounding installation decreases the risk of electric shock by opening a path with low resistance for the electricity flow in case of a malfunction

or failure. Power cable of this product

is equipped with a conductor and a grounding plug that allows for grounding the product. This plug must be installed appropriately and inserted into a socket which is grounded in accordance with the local laws and regulations.

door with a lock, sliding door or a door that has a hinge against the hinge of

the dryer.

• Do not install or leave this product

in places where it will be exposed to outdoor conditions.

• Do not tamper with the controls.

• Do not perform any repair or part

replacing procedures on the product even if you know or have the ability to perform unless it is clearly suggested in the operating instructions or the published service manual.

• Inside and exhaust duct of the product

must be cleaned by the qualified service personnel periodically.

• Wrong connection of grounding

conductor of the product can cause

electric shock. If you have any suspect

about the grounding connection, have it checked by a qualified electrician, service representative or service personnel.

• Do not reach into the machine when

the drum is spinning.

• Unplug the machine when it is not in

use.

• Never wash down the appliance

with water! There is the risk of electric shock! Always disconnect by unplugging from the mains before cleaning.

• Never touch the plug with wet hands.

Never unplug by pulling on the cable,

always pull out by grabbing the plug only. Do not operate the machine if the power cable or plug is damaged!

• Never attempt to repair the machine

yourself, otherwise, you will be putting your life and others’ lives in danger.

• For malfunctions that cannot be solved

by following the information given in

the safety instructions:

Turn off the machine and contact an

authorised service agent.

• Do not stop the dryer before the drying

cycle comes to an end unless you will remove all laundry from the dryer fast in order to lay them and dissipate the heat.

• Remove the door of the drying

compartment before decommissioning or disposing of the product.

• The final step of the drying cycle (cool-

down cycle) occurs without applying heat to ensure that the items are left

at a temperature that will not damage them.

• Fabric softeners or similar products

should be used as specified by the fabric softener instructions.

• Underwear that contains metal

reinforcements should not be placed in a dryer. Damage to the dryer can result if metal reinforcements come loose during drying.

• Check all garments for forgotten

lighters, coins, metal pieces, needles, etc. before loading.

• At times when your dryer is not in

use or after the laundry is taken out following the completion of drying

process, turn off by using the On/ Off button. In cases when the On/

Off button is on (while the dryer is

energized), keep the door of the dryer

closed.

Intended use

• This product has been designed for domestic use. It should not be used for

other purposes.

• Use the product only for drying laundry

that are marked accordingly.

• Dry only those articles in your product

that are stated in this manual.

• This product is not intended to be

used by persons with physical, sensory or mental disorders or unlearned or inexperienced people (including children) unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product.

Children’s safety

• Electrical appliances are dangerous for the children. Keep children away from

the machine when it is operating. Do not let them tamper with the machine.

• Packaging materials are dangerous to children. Keep the packaging materials

out of reach of children or dispose them by classifying according to waste directives.

• Do not allow children sit/climb on or

enter in the product.

• Children should be supervised to

ensure that they do not play with the product.

• Close the loading door when you leave

the area where the product is located.

3 Installation

Refer to the nearest Authorised Service

Agent for installation of your product.

C Preparation of location and electrical

installation for the product is under customer’s responsibility.

B Installation and electrical connections

must be carried out by a qualified personnel.

A Prior to installation, visually check if

the product has any defects on it. If

so, do not have it installed. Damaged products will cause risks for your safety.

Appropriate installation location

• Install the product in an environment which has no risk of freezing and is in a

stable and level position.

• Operate your product in a well

ventilated, dust-free environment.

• Do not block the air ducts in front of

and under the product with materials such as long pile rugs and cupboard plinths.

• Do not place your product on a long

pile rug or on similar surfaces.

• Do not install the product behind a

door with a lock, sliding door or a hinged door which can strike the product.

• Once the product is installed, it should

stay at the same place where its connections have been made. When installing the product, make sure that the rear wall of it does not touch anywhere (tap, socket, etc.) and also pay attention to install the product at a place where it will stay permanently.

BDo not place the product on top of the

power cable.

• Keep at least 1.5 cm distance to walls

of other furniture.

Under Counter Installation

• Leave at least 3 cm of space between

the side and rear walls of the machine

and the walls of the counter/cupboard

when installing your machine under a

counter or in a cupboard. Never use

the tumble dryer without top plate.

Ventilation hose and connection (for products equipped with an outlet vent)

Ventilation hose assures exhausting of the air from inside the machine. Vented dryer has 1 air outlet. Stainless sheet metal or aluminum pipes can be used instead of the hose. The diameter of the pipe to be used should be minimum 10 cm. Maximum hose and pipe lengths are given in the table below.

Hose Pipe

Maximum length 4 m 5 m 1 elbow 45° -1.0 m -0.3 m

1 elbow 90° -1.8 m -0.6 m

1 elbow 90° short -2.7 m

1 wall passage -2.0 m -2.0 m

C Each elbow and other passages

should be subtracted from the above maximum length.

To connect a ventilation hose;

1. Connect the air outlet hose to the hose spacer piece by turning it anticlockwise.

2. Make the hose passages as shown below.

C Exhaust of humid air from the dryer

into the room is inconvenient. It may damage the walls and furniture in the room.

C The ventilation hose can be routed

outdoors via a window or it can be connected to an air outlet in the wall (see diagram below).

C Air outlet hose must be extended

directly to the outdoors. There must be a small number of elbows as not to hinder air ventilation.

C To prevent water accumulation in the

hose, make sure that it is not folded on

the oor.

B The air ventilation hose should not be

connected to the chimney of a stove or

a replace.

B Do not operate your machine at the

same time with heaters such as a coal

or gas stove. Airow may cause the chimney to are up. Airow may cause the chimney to ame up.

Adjusting feet

In order to ensure that your product

operates more silently and vibrationfree, it must stand level and balanced on its feet. Front feet of your product can be adjusted. Balance the machine by adjusting the feet.

1. Loosen the feet by hand.

2. Adjust the feet until the product stands level and firmly on the floor.

C Do not use any tools to loosen the

adjustable feet, otherwise, they can be damaged.

C Never remove the adjustable feet from

their housings.

2 plastic pieces supplied along with the user manual prevent your machine from slipping on wet and slippery surfaces. To

install the plastic parts:

1. Tilt your product to backwards.

2. Fit the plastic parts on to the front

adjustable feet. Press on the plastic

parts to snap them into their seating.

3. Check the balance of your product again and readjust the adjustable feet if necessary.

First use

• To have the product ready for

operation before calling the authorised service agent, make sure that its location and power supply installations

are appropriate. If they are not, call

a qualified electrician to have any necessary arrangements carried out.

• Make sure that the power connections

of the product are in accordance with the instructions given in relevant chapters of this manual.

Disposing of packaging material

Packaging materials are dangerous to children. Keep packaging materials in

a safe place out of reach of children.

Packaging materials of your product are

manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste.

Transportation of the machine

1. Unplug the machine from the mains.

2. Remove the water drain (if any) and

chimney connections.

3. Drain water remained in the machine completely before transportation.

Disposing of the old machine

Dispose of your old machine in an environmentally friendly manner.

Refer to your local dealer or solid waste

collection centre in your area to learn how to dispose of your machine. Before disposing of your old machine, cut off the power cable plug and make the loading door lock unusable to avoid dangerous conditions to children.

+ 19 hidden pages