Beko DFN16210X, DFN16210W, DFN16210B User manual
Dishwasher
User’s Manual
EN
Document Number :
15 0167 0100_AB_BEKO_B6_EN/ 31-07-17.(16:08)
Please read this user manual first!
Dear Customer,
We hope that you get the best results from your product which has been manufactured
with high quality and state-of-the-art technology. Therefore, please read this entire
user manual and all other accompanying documents carefully before using the product
and keep it as a reference for future use. If you handover the product to someone else,
give the user manual as well. Follow all warnings and information in the user manual.
Remember that this user manual is also applicable for several other models. Differences
between models will be identified in the manual.
Explanation of symbols
Throughout this User Manual the following symbols are used:
Important information or useful
C
A
hints about usage.
Warning for hazardous
situations with regard to life and
property.
Warning for electric shock.
B
Packaging materials of the
product are manufactured
from recyclable materials in
accordance with our National
Environment Regulations.
Do not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated by the local
authorities.
Dishwasher
User’s Manual
EN
Document Number :
15 0167 0100_AB_BEKO_B6_EN/ 31-07-17.(16:08)
Please read this user manual first!
Dear Customer,
We hope that you get the best results from your product which has been manufactured
with high quality and state-of-the-art technology. Therefore, please read this entire
user manual and all other accompanying documents carefully before using the product
and keep it as a reference for future use. If you handover the product to someone else,
give the user manual as well. Follow all warnings and information in the user manual.
Remember that this user manual is also applicable for several other models. Differences
between models will be identified in the manual.
Explanation of symbols
Throughout this User Manual the following symbols are used:
Important information or useful
C
A
hints about usage.
Warning for hazardous
situations with regard to life and
property.
Warning for electric shock.
B
Packaging materials of the
product are manufactured
from recyclable materials in
accordance with our National
Environment Regulations.
Do not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated by the local
authorities.
CONTENTS
1 INSTRUCTIONS FOR SAFETY
AND ENVIRONMENT 4
General safety .......................................4
Intended use ..........................................4
Children’s safety ...................................5
Disposing of packaging material ........ 5
Transportation of the product ...........6
Compliance with WEEE Directive and
Disposing of the Waste Product .........6
Compliance with RoHS Directive........6
Package information ............................6
2 DISHWASHER 7
Overview ................................................7
Technical specifications ......................8
3 INSTALLATION 9
Appropriate installation location .......9
Connecting water supply ....................9
Aquasafe+ .......................................... 10
Connection to the drain .................... 10
Adjusting the feet ..............................11
Electrical connection ..........................11
Initial use ..............................................11
4 PREPARATION 12
Tips for energy saving .......................12
Water softening system ....................12
Adjusting the water softening
system ..................................................12
Adding salt .......................................... 14
Detergent .............................................15
Adding detergent ...............................15
Combined tablet detergents ............17
Rinse aid ...............................................17
Silverware basket piece ................... 20
Silverware basket .............................. 20
Cutlery basket .....................................21
Cutlery basket .....................................21
Collapsible lower basket wires (6
pieces) ................................................. 22
Collapsible lower basket wires (4
pieces) ................................................. 23
Collapsible lower basket wires (2
pieces) ................................................. 23
Collapsible lower basket tines ......... 24
Collapsible lower basket tines ......... 25
Lower basket bottle wire ................. 25
SoftTouch Accessory ........................ 26
Lower Basket Glass Holder .............. 26
Tray Wash Supports .......................... 26
Lower basket multipurpose / height
adjustable service rack ......................27
Upper basket height adjustable rack 28
Upper basket drawer......................... 28
Upper basket glass support piece ... 28
Upper basket glass support piece ... 29
Collapsable upper basket wires ...... 29
Collapsible upper basket tines ........ 30
Collapsible upper basket tines ........ 30
Adjusting the height of the upper
basket ...................................................31
Adjusting the height of loaded upper
basket .................................................. 32
Height setting with empty basket .. 33
5 OPERATING THE PRODUCT 34
Keys ...................................................... 35
Preparing the machine ..................... 35
Programme selection ........................ 35
Auxiliary functions .............................37
Scheduling the washing time .......... 38
Starting the programme ................... 39
Cancelling the programme ............... 40
Salt indicator ( ) .............................. 40
Rinse Aid indicator ( ) .....................40
End of programme ............................. 40
Water cut-o warning ...................... 40
Overowing warning ........................40
6 MAINTENANCE AND
CLEANING 41
Cleaning the outer surface of the
product ................................................ 41
Cleaning the interior of the machine 41
Cleaning the filters ............................ 41
Cleaning the hose filter .................... 42
Cleaning the impellers ...................... 43
Lower impeller ................................... 43
Upper impeller ................................... 43
7 TROUBLESHOOTING 44
instructions for safety and environment
1
This section contains safety
instructions that will help to
get protected from risk of
personal injury or property
damage. Failure to follow
these instructions shall void all
warranties.
General safety
• Never place the product
on a carpet-covered floor;
otherwise, lack of airflow
beneath the product will
cause electrical parts to
overheat. This will cause
problems with your product.
• Do not operate the product
if the power cable / plug is
damaged! Call the Authorised
Service Agent.
• Connect the product to a
grounded outlet protected
by a fuse complying with
the values in the “Technical
specifications” table. Do
not neglect to have the
grounding installation made
by a qualified electrician.
Our company shall not be
liable for any damages that
will arise when the product
is used without grounding
in accordance with the local
regulations.
• The water supply and
draining hoses must be
securely fastened and remain
undamaged.
• Unplug the product when not
in use.
• Never wash the product by
spreading or pouring water
onto it! There is the risk of
electric shock!
• Never touch the plug with
wet hands! Never unplug by
pulling on the cable, always
pull out by grabbing the plug.
• The product must
be unplugged during
installation, maintenance,
cleaning and repairing
procedures.
• Always have the installation
and repairing procedures
carried out by the Authorised
Service Agent. Manufacturer
shall not be held liable for
damages that may arise from
procedures carried out by
unauthorised persons.
• Never use chemical solvents
in the product. They bring
forth the risk of explosion.
• When you pull the upper
and lower baskets out
completely, the door of the
product will bear all the
weight of the baskets. Do not
put other loads on the door;
otherwise, the product may
tilt.
• Never leave the door of
the product open apart
from loading and unloading
procedures.
• Do not to open the door
of the product when it is
running unless necessary.
Be careful for the rush of hot
vapour when you need to
open the door.
Intended use
• This product has been
designed for domestic use.
4 Dishwasher / User’s Manual/49 EN
instructions for safety and environment
• It must be used to do the
domestic type dishes only.
• This appliance is intended
to be used in household and
similar applications such as:
- Staff kitchen areas in shops,
offices and other working
environments;
- Farm houses;
- By clients in hotels, motels
and other residential type
environments;
- Bed and breakfast type
environments
• Only dishwasher safe
detergents, rinse aids and
additives must be used.
• The manufacturer waives
any responsibility arisen
from incorrect usage or
transportation.
• The service life of your
product is 10 years. During
this period, original spare
parts will be available to
operate the product properly.
• This appliance can be used by
children aged from 8 years
and above and persons with
reduced physical,sensory
or mental capabilities or
lack of experience and
knowledge if they have
been given supervision or
instruction concerning use
of the appliance in a safe
way and understand the
hazards involved. Children
shall not play with the
appliance. Cleaning and user
maintenance shall not be
made by children without
supervision.
Children’s safety
• Electrical products are
dangerous for the children.
Keep children away from the
product when it is in use. Do
not let them to tamper with
the product.
• Do not forget to close the
door of the product when
leaving the room where it is
located.
• Store all detergents and
additives in a safe place
away from the reach of the
children.
Disposing of
packaging material
Packaging materials are
dangerous to children. Keep
packaging materials in a safe
place away from reach of the
children.
Packaging materials of the
product are manufactured from
recyclable materials. Dispose
of them properly and sort in
accordance with recycled waste
instructions. Do not dispose
of them with normal domestic
waste.
Dishwasher / User’s Manual
5 / 49
EN
instructions for safety and environment
Transportation of the
product
If you need to move the
A
1. Unplug the product before
2. Remove water drainage and
3. Drain the remaining water in
product, do it in upright
position and hold from
the rear side. Slanting
the product onto its
front side may cause
the electronic parts in it
get wet and damaged.
transporting it.
water supply connections.
the product completely.
Compliance with
WEEE Directive and
Disposing of the
Waste Product
This product complies with
EU WEEE Directive
(2012/19/EU). This product
bears a classification
symbol for waste electrical and
electronic equipment (WEEE).
This product has been
manufactured with high quality
parts and materials which can be
reused and are suitable for
recycling. Do not dispose of the
waste product with normal
domestic and other wastes at the
end of its service life. Take it to
the collection center for the
recycling of electrical and
electronic equipment. Please
consult your local authorities to
learn about these collection
centers.
Compliance with RoHS
Directive
The product you have purchased
complies with EU RoHS Directive
(2011/65/EU). It does not contain
harmful and prohibited materials
specified in the Directive.
Package information
Packaging materials of the
product are manufactured
from recyclable materials in
accordance with our National
Environment Regulations. Do
not dispose of the packaging
materials together with the
domestic or other wastes. Take
them to the packaging material
collection points designated by
the local authorities.
6 Dishwasher / User’s Manual/49 EN
2
Dishwasher
Overview
15
Dishwasher / User’s Manual
1. Top Cover (depends on model)
2. Upper impeller
3. Lower basket
4. Lower impeller
5. Filters
6. Rating Label
7. Control panel
8. Door
9. Detergent dispenser
10. Lower impeller slot
11. Cutlery basket
12. Salt reservoir lid
13. Upper basket rail
14. Upper basket
15. Fan drying system (depends on model)
EN
7 / 49
Dishwasher
Technical specications
Compliance to standards and test data / EC declaration of conformity
This product complies with the following EU directives;
Development, production and sales stages of this product comply with the safety
rules included in all pertaining European Community regulations.
2014/35/EU, 2014/30/EU, 93/68/EC, IEC 60436/DIN 44990, EN 50242
Power input 220-240 V, 50 Hz (see rating label)
Total power consumption 1800-2100 W (see rating label)
Heater power consumption 1800 W (see rating label)
Total current (depends on the model) 10 A (see rating label)
Drain pump power consumption 30 W (see rating label)
Water pressure 0.3 –10 bar (= 3 – 100 N/cm² = 0.01-1.0
Mpa)
Technical specifications may be changed without prior notice to improve the
C
quality of the product.
Figures in this manual are schematic and may not match the product exactly.
C
Values stated on the markings of the product or in the printed documents
C
Note for test nsttutons:
Data required for performance tests shall be provided upon request. Requests can be
e-mailed to the following address:
dshwasher@standardloadng.com
Do not forget to provide the code, stock and serial numbers of the product to be tested in
your request e-mail along with your contact information. Code, stock and serial numbers of
the product may be found on the type label attached to the side wall of the door.
8 Dishwasher / User’s Manual/49 EN
accompanying the product are obtained in the laboratory on basis of the
relevant standards. Depending on operational and environmental conditions of
the product, these values may vary.
3
Installation
Refer to the nearest Authorised Service
Agent for installation of your product. To
make the product ready for use, make sure
that the electricity, tap water supply and
water drainage systems are appropriate
before calling the Authorised Service
Agent. If they are not, call a qualified
technician and plumber to have any
necessary arrangements carried out.
Preparation of the location
C
B
A
C
When placing the product, pay attention
not to damage the floor, walls, piping, etc.
Do not hold the product from its door or
panel to move it.
and electrical, tap water and
waste water installations at the
place of installation is under
customer's responsibility.
Installation and electrical
connections must be carried
out by the Authorised Service
Agent. Manufacturer shall
not be held responsible
for damages arising from
processes carried out by
unauthorised persons.
Prior to installation, visually
check if the product has any
defects on it. If so, do not have
it installed. Damaged products
cause risks for your safety.
Make sure that the water inlet
and discharge hoses are not
folded, pinched or crushed
while pushing the product into
its place after installation or
cleaning procedures.
Appropriate installation
location
• Place the product on a solid and flat
floor that has sufficient load carrying
capacity! The product must be
installed on a flat surface in order for
the door to be closed comfortably and
securely.
• Do not install the product at places
where temperature may fall below
0ºC.
• Place the product at least 1 cm away
from the edges of other furniture.
• Place the product on a rigid floor. Do
not place it on a long pile rug or similar
surfaces.
Do not place the product on the
B
• Make sure that you select a location
• Install the product in a place close to
power cable.
that will allow you to load and unload
the dishes in a fast and comfortable
manner.
the tap and the drain hole. Select the
installation location by considering
that it will not be changed after the
connections are made.
Connecting water supply
We recommend attaching a
C
filter on the house/apartment
supply water inlet to protect
the machine from damages
that may arise from impurities
(sand, dirt, rust, etc.) coming
from the urban water supply
system or from your own water
system as well as to prevent
complaints such as yellowing or
sludge accumulation at the end
of washing.
Dishwasher / User’s Manual
9 / 49
EN
Installation
Permtted water temperature: up
to 25°C
The dishwasher may not be connected to
open warm water devices or flow-through
water heaters.
• Do not use old or used water inlet
hose on the new product. Use the new
water inlet hose supplied with the
product.
• Connect the water inlet hose directly
to the water tap. Pressure coming
from the tap should be minimum 0.3
and maximum 10 bars. If the water
pressure exceeds 10 bars, a pressure
relief valve should be installed in
between.
• Open the taps completely after
making the connections to check for
water leaks.
Use a screw-on hose connector
C
to connect the water inlet hose
to a water tap with a ¾ inch
external thread. If required, use
a filter insert to filter deposits
from the pipes.
Aquasafe+
(depends on model)
The Aquasafe+ system protects against
water leaks that may occur at the hose
inlet.Water contact with the valve box of
the system must be avoided to prevent
damage to the electrical system. If the
Aquasafe+ system is damaged, unplug the
product and call the Authorised Service
Agent.
As the hose set contains
A
electrical connections and
assemblies, never shorten
or lengthen the hose with
extension hoses.
A
10 Dishwasher / User’s Manual/49 EN
For your safety, close the water
inlet tap completely after the
washing programme is over.
Connection to the drain
Water discharge hose can directly be
connected to the drain hole or sink’s
drainage. The length of this connection
must be min. 50 cm and max. 100 cm from
the floor. A discharge hose longer than 4
meters causes dirty washing.
Attach the water discharge hose to the
drainpipe without bending it. Tightly fix
the water discharge hose to the drainpipe
in order to prevent any dislocation of the
water discharge hose during operation of
the product.
Installation
min
300
min
120
max 1000
min 500
C
Drainpipe must be connected
to the sewage system and it
should not be connected to any
surface water.
• The voltage and allowed fuse or breaker
protection are specified in the “Technical
specifications” section. If the current
value of the fuse or breaker in the house
is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
• The specified voltage must be equal to
your mains voltage.
• Do not make connections via extension
cables or multi-plugs.
Damaged power cables must
B
B
be replaced by the Authorised
Service Agent.
If your dishwasher is equipped
with internal illumination, lamp
should only be replaced by the
Authorised Service Agent in
case of failures that may occur
on the lamp.
Adjusting the feet
If the door of the product cannot be closed
properly or if the product swings when you
push it slightly, then you need to adjust
the feet of the product. Adjust the feet of
the product as illustrated in the installation
manual supplied with the product.
Electrical connection
Connect the product to a grounded outlet
protected by a fuse complying with the
values in the “Technical specifications”
table. Our company shall not be liable for
any damages that will arise when the
product is used without grounding in
accordance with the local regulations.
• Connection must comply with national
regulations.
• Power cable plug must be within easy
reach after installation.
Unplug the product after the
B
Dishwasher / User’s Manual
washing programme is over.
If the product has a failure, it
B
should not be operated unless
it is repaired by the Authorised
Service Agent! There is the risk
of electric shock!
Initial use
Before starting to use the product, make sure
that all preparations are made in accordance
with the instructions in sections “Important
safety instructions” and “Installation”.
• To prepare the product to do the dishes,
perform first operation in the shortest
programme with detergent while the
machine is empty. During the initial use,
fill the salt reservoir with 1 litre of water
prior to filling it with salt.
There might be a small amount
A
of water left in the product
after factory quality control
tests. This has no harm on the
product.
EN
11 / 49
Preparation
4
Tips for energy saving
Following information will help you use
the product in an ecological and energyefficient manner.
Wipe away any coarse food remnants on
the dishes before putting them in the
product. Operate the product after filling it
completely. When selecting a programme,
consider the table of “Programme data and
average consumption values”.
Do not put more detergent than suggested
on the detergent package.
Water softening system
Your dishwasher requires soft
C
water. If the hardness of the
water is above 6°dH, the water
must be softened and descaled.
Otherwise, ions that create
the hardness will accumulate
on the surfaces of the dishes
and may adversely affect the
washing, shining and drying
performances of the product.
Adjusting the water
softening system
Cleaning, rinsing and drying performance of
your dishwasher will increase when water
softening system is adjusted properly.
Adjust the new water hardness level
according to the Water hardness level
instruction in this booklet.
Use the test strip supplied with the product
according to the steps given below to
determine hardness level of your supply
water.
The product is equipped with a water
softening system which reduces the
hardness of incoming water. This system
softens the supply water that enters
into the product to a level that will allow
washing the dishes with the required
quality.
12 Dishwasher / User’s Manual/49 EN
Preparation
a b
Remove the test
strip from the
packet.
1 min.
Turn on the tap and
let the water run for
about a minute.
c
1 Second
Hold the test strip in
the water for about
a second.
d e f
1 Minute
Remove the test
strip from the water
and shake it.
Wait for 1 minute. The test strip shows
you the hardness
level.
After determining hardness level of the supply water:
1. Turn on the machine, press and hold Time Delay and Programme keys simultaneously for
3 seconds to enter the settings menu.
2. Press the programme key until the Salt indicator starts to flash. Current regeneration
stage is displayed on the programme indicator.
3. Using Time Delay key, adjust water hardness level according to the hardness of the
supply water. See “Water hardness level adjustment table” for correct setting.
4. Press On / Off key to save the setting.
Water hardness level adjustment table
Hardness
Level
0th Level
1st Level
2nd Level
3rd Level
4th Level
5th Level
English Water
Hardness °dE
0-5 0-4 0-8
6-9 5-7 9-13
10-15 8-12 14-22
16-19 13-15 23-27
20-24 16-19 28-34
25-62 20-50 35-90
German Water
Hardness °dH
French Water
Hardness °dF
Water Hardness Level Indicator
Press the Time Delay key to switch the water hardness level
to position P1.
Press the Time Delay key to switch the water hardness level
to position P2.
Press the Time Delay key to switch the water hardness level
to position P3.
Press the Time Delay key to switch the water hardness level
to position P4.
Press the Time Delay key to switch the water hardness level
to position P5.
Perform the same hardness level adjustment that you have set on the control panel also
with the regeneration adjustment switch. For example, if you have adjusted to “3rd level”
in the control panel, also set the regeneration adjustment switch to 3rd level.
Regeneration Adjustment Switch
0th Level 1st Level 2nd Level 3rd Level 4th Level 5th Level
Dishwasher / User’s Manual
1 1 2 3 4 5
13 / 49
EN
Preparation
If the hardness level of the supply water is
above 90 °dF or if you are using well water,
then it is recommended to use water
purification devices and special filters.
If the hardness level of the supply water is
below 13°dF, there is no need to use salt
in your dishwasher. If this is the case, “No
Salt Warning Indicator” (if any) illuminates
continuously on the panel of your machine.
If the water hardness level adjustment
is set to level 1, the “No salt warning
indicator” will illuminate continuously
although it is not necessary to use salt. If
you use salt under this condition, salt will
not be consumed and the Salt indicator will
not illuminate.
If you move your house, it is
C
Adding salt
Water softening system needs to be
regenerated in order that the product
operates with the same performance
continuously. Dishwasher salt is used for
this purpose.
C
C
necessary to readjust water
hardness level of your machine
by considering the information
given above according to the
hardness level of the supply
water in your new location.
Your machine will display the
most recently adjusted water
hardness level.
Use only special softening salts
produced particularly for the
dishwashers in your machine.
We recommend using granular
or powder softening salts. Do
not use salts that are insoluble
in water such as table salt or
common salt. Performance of
water softening system may
get worse in time.
Salt reservoir will fill with water
C
1. First take the lower basket out to add
2. Turn the salt reservoir lid counter
C
C
when you start the product.
Therefore, add the softening
salt before starting the
machine.
softening salt.
clockwise to open it (A, B).
Salt reservoir will fill with water
when you start the product.
Therefore, add the softening
salt before starting the
machine.
Before initial use, fill the water
softening system with 1 litre of
water (C).
14 Dishwasher / User’s Manual/49 EN
Loading...