Beko D 5061 B, D 5102 BS, D 5081 BS, D 5101 B, D 5081 B User Manual

...

D 5102 B D 5101 B D 5081 B D 5062 B D 5102 BS D 5082 B D 5081 BS D 5061 B

W a s h i n g M a c h i n e

U s e r ’ s M a n u a l

Dear Customer, We wish that this product, manufactured at modern facilities with total quality notions, will deliver you the best performance. In order to guarantee this, please read this instruction manual thoroughly and keep it for your future reference.

Contents

Technical Features of Your Washing Machine 5

Warning 7

Preparation 9

Program Selection and Starting Machine 13

Care and maintanence 18

Installation 20

Helpful tips on stain removal 23

Before calling service 24

Technical Features of Your Washing Machine

D 5102 B D 5102 BS D 5101 B

Maximum dry laundry capacity (kg.) 5 5 5

Height (cm.) 85 85 85

Witdh (cm.) 60 60 60

Depth (cm.) 54 54 54

Net Weight (kg.) 64 64 64

Electricity (V/Hz.) 220-240/50 220-240/50 220-240/50

Total Current (A) 10 10 10

Total Power (W) 2100-2450 2100-2450 2100-2450

Washing -rinsing cycle (cyc/min) 52 52 52

Spinning cycle (max cyc/min) 1000 800 600

There amy be changes in the technical featues without prior notice in order to enhance product quality.

The figures in the manual are schematical and may not represent your actual machine one-to-one.

D 5082 B D 5081 B D 5081 BS

D 5061 B D 5062 B

� tions with given standards. These values may vary according to usage and environmental conditions.

Your Washing Machine

Top Lid

Front Panel

Handle

Kick Plate Cover

Front door

Kick Plate

Warning

• This product is designed for home use.

• Your washing machine is adjusted to 220V.

• If the fuse in your house is less than 16A than have a certified electrician deploy an 16A fuse.

• In case of transformer or non-transformer use,

grounding installation must be performed with a licensed electrician. Any use before grounding is not our responsibility.

• Never place your machine over a carpet covered

floor. Otherwise electrical parts of your machine may overheat. This may cause malfunction of your machine.

• Make sure hot and cold taps are connected correctly.

Otherwise your laundry may come out hot and torn .

• Please call certified service for a failure of electric plug/

cable.

• Be careful about your water hoses are not old. Do not

use old/torn water hoses. This may cause stain in your laundry .

• At first use, washing must be performed at Cotton 90°C

program without loading with laundry for getting your machine ready for washing.

• Performance of your washing machine depends on

the quality of water and hygiene compound used. If low quality and unfitting cleaning material is used the

stains will be fixed. Before washing your laundry with stain keep your attention on cleaning the laundry as explained in following pages.

• Lifetime of your product is 10 years.

This is period of keeping spare parts for your machine

to operate.

• Because of quality control procedures there might be little amount of water in your machine.

This does not have any damage to your machine.

• Your machine is programmed for starting operation again when electricity is off and on afterwards. You can not press On/Off button to cancel program. Machine will go on program when electricity is on. To CANCEL the program press >Start/Pause/Cancel< button for three seconds. (See. Canceling a program)

• If pre-wash additional function led is blinking than your machine is in child-proof-lock position. (See. childproof-lock)

If “Ready” led on program progress display is blinking

program selection knob is middle position. In this case turn the knob and adjust it again. If the warning continues call authorized service.

• After your machine starts operation if Start/Pause/ Cancel key starts blinking than door is not locked. Open and close the door again begin washing program

again.

• If “washing” led on program progress display is blinking either there is no water or tap is off. Check your taps. Turn your machine off and on. If the problem persists unplug your machine, turn off tap water and call authorized service.

• If program is started or program selection can not be performed your machine might be in protection mode due to infrastructure problem (voltage, water pressure, etc.) Press and hold the > Start/Pause/Cancel < button for 3 seconds in order to switch machine to factory settings. Simultaneously, “Cancel” will appear on the display.

• Most of the warnings resulting in calling an authorized service are due to infrastructure problems. For this reason applying to an Authorized Service is recommended.

+ 16 hidden pages