Page 1
Update 01/2004
Code# Description
TL7503BL Tri-Liner, Blue, complete
TL76643RBLGE Wing-Holder, RH, Set of 3
TL7664RBLGE Wing-Holder, RH
TL76643LBLGE Wing-Holder, LH, Set of 3
TL7664LBLGE Wing-Holder, LH
NA1 Nockadapter for Nockbed #1, Black
NA2 Nockadapter for Nockbed #2, Orange
TL7631RT Tri-Liner, Tags, Red
TL99001 Tri-Liner, Ruler (Arm), Blue
TL99002 Tri-Liner, Segment (1/3), Blue
TL99003 Tri-Liner, Body, Blue
TL99004 Tri-Liner, Ring, Grey
TL99005 Tri-Liner, Cover, Blue
TL99006 Tri-Liner, Indicator, Red
TL99007 Tri-Liner, Screw
BEITER TRI-LINER & WING HOLDER
Tri-Liner
Single Spare Parts
Wing-Holder
The WING-HOLDER
The Beiter Wing-Holder is designed to position and fletch
vanes (e.g. Spin Wings™, Rite Flite™, Kurly Vanes™...) easily
and precisely on arrow shafts.
It is available for Right-hand (RH) and Left-Hand (LH),
and for vane lenght 1-3/4" only.
The Beiter Wing-Holder comes with a Bushing, which
allows off-set of the vane by 1°.
HOW TO PREPARE THE VANE
Clean the arrow shaft with acetone (before installing the nock!)
Draw the necessary lines with the Beiter Tri-Liner.
pic. 2
pic. 3
Insert the vane in the Beiter Wing-Holder (Pic.2) and align it with the edge as
shown in Pic.3.
Strip off the first layer of the tape as much as needed and hold it down in one of
the grooves on the back of the Beiter Wing-Holder. - Pic.4
Turn the Beiter Wing-Holder and position the tape along the edge of the vane. -
Pic.5
Press on the tape. Than cut the useless parts of the tape on both sides with scissors
or a knife. - Pic.6
Hint: Prepare more vanes ready to be fletched on more Wing-Holders and keep
them safe in your quiver or bowcase. You will have one or more spare vanes ready
to use!
pic. 1
pic. 4
HOW TO FLETCH THE VANE
Strip off the second layer of the tape, so the fletching surface is free.
Put the Beiter Wing-Holder on the arrow shaft, so that both pins are in contact
with the shaft. Don't let the tape have contact with the shaft.
Align the Beiter Wing-Holder along the drawn line, using the three positioning
sectors placed along the vane edge. - Pic.7
Note: Place the vane in the correct direction on the shaft, as shown on the Beiter
pic. 5
Wing-Holder (Nock - Point) - Pic.1
Pay attention to place the vane along the drawn line and not on it! The tape won't
hold on the line. Now press the Beiter Wing-Holder on the shaft.
Than release the pressure completely and turn away the shaft from the Beiter
Wing-Holder. - Pic. 8
Eventually press the vane
pic. 6
on the shaft with your
thumb on the medium
sector (should not be
Werner Beiter
Daimlerstr. 18
DE-78083 Dauchingen
pic. 7
pic. 8
pic. 9
necessary, if the shaft has
been cleaned well!).
You may fletch your vanes
straight (parallel to the
drawn line) or 1° off-set:
simply install the red
bushing delivered with the
Beiter Wing-Holder
over the front pin (Point>), by pressing it in. Pic. 9
www.WernerBeiter.com
Tel. +49 7720 856860
Fax +49 7720 4238
email: info@wernerbeiter.com
Loading...