BEI Sensors 8360 User Manual
8360 Series
8360 Series
360° Non-Contacting Through-Hole Position Sensor
360° Non-Contacting Through-Hole Position Sensor
The 8360 Series is BEI Sensors’ latest addition to the company’s line-up of robust, reliable,
and highly accurate non-contacting position sensors. The 8360’s low prole and through-
hole design make it desirable for applications like steering wheel and boom angle, where
space is limited and the sensor must mount around a shaft. The sensor’s dual analog output
is capable of resolving 360 degrees of motion with high accuracy and 12 bit resolution.
The 8360 Series provides IP65 sealing, 360 degree continuous rotation, a robust package
and wide operating temperature range, making it especially well suited for applications with
harsh environments like industrial vehicles, agricultural and construction equipment and
process controls. Non-contacting, redundant outputs provide the high reliability and long
life that are an absolute necessity in applications such as medical equipment or wind/solar
energy applications. A wide range of adaptations are available including PWM or Can Bus
output, shaft interface, electrical angle, connector type, cable length, output slope and much
more.
Features
Non-contacting technology
Provides long life
Output signal choices
Analog, PWM, CAN Bus
Electrical angle
The standard version is available with rotational angles in 15 degree increments, up to 360°
Connector
Flying lead terminated w/6 pin AMP connector P/N 776434-1, contact P/N 1924463-1, other options
available
BEI Sensors
BEI Sensors
Through-hole design
Fits around shaft, shaft options available
Environmental
IP65-protected from dust and water jets
Operating temperature
-30° to +85°C standard, (option for -40°C to +125°C)
Electrical protection
Overvoltage, short circuit, ESD
Magnetic Shielding to 20G
Mechanical Specications Electrical Specications Environmental Specications
Mechanical travel : travel 0° to +360° with no stops,
allowing for 360 degree continuous rotation
Actuation (starting) Torque : 0.2 N-m (28.5 oz-in)
Weight 220 grams max.
Rotational life : 10 million revolutions
Electrical angle : 15° to 360° in 15 degree increments
standard (other options available)
Input voltage : 5.0 V±0.25V DC
Input current : 16mA maximum per output
32mA maximum total (both channels)
Sensor Output : 0.25V – 4.75V for Analog at 5.0V input
Accuracy : +/- 0.6%
Resolution : 12 Bit, 0.088 degree
Environmental Sealing : IP65 standard
Electromagnetic compatibility : 100V/meter, 15kHz –
1GHz range
Vibration : 10 – 10,000 Hz, Total PSD: 4.94 Grms
Shock : 50Gs, half sine pulse, 11 m sec duration
Operating temperature range : -30°C to +85°C (wider
operating temperature -40° to +125 C° available)
Storage temperature range : -40°C to +105°C
Ordering information FOR ASSISTANCE CALL 800-350-2727
SAMPLE: 8360075 (8360 Sensor with 75 Degrees Active Electrical Angle
8360XXX
*Standard Active Electrical Angles
015 = 15 degrees 195 = 195 degrees
030 = 30 degrees 210 = 210 degrees
045 = 45 degrees 225 = 225 degrees
060 = 60 degrees 240 = 240 degrees
075 = 75 degrees 255 = 255 degrees
090 = 90 degrees 270 = 270 degrees
105 = 105 degrees 285 = 285 degrees
120 = 120 degrees 300 = 300 degrees
135 = 135 degrees 315 = 315 degrees
150 = 150 degrees 330 = 330 degrees
165 = 165 degrees 345 = 345 degrees
180 = 180 degrees 360 = 360 degrees
Consult factory for options including:
• Non-standard output slope
• Clipped outputs
• Non-standard Active Electrical Angles
• PWM output (pulse width modulation)
• Special marking
• CAN Bus output
• Multi-turn
• Lead length
• Connector type
• IP67 sealing
• Shaft interface
7230 Hollister Avenue
Goleta, CA 93117
www.beisensors.com
Tel: 800-350-2727
Fax: 805-968-3154
Rev 2-27-13
8360 Series
360° Non-Contacting Through-Hole Position Sensor
Dimensions
Dimensions
BEI Sensors
Spline Details
Rotor Interface is 12 tooth spline
Pitch Angle: 30°
Diametral Pitch: 16/32
Pitch Diameter: 19.05
Largest Diameter: 20.3 ± 0.1
Smallest Diameter: 16.5 ± 0.5/-0
(Ref ANSI B92.1 - 1970 Tol. Class B)
Connector
Connector Pin Layout
PIN # Pinout Color
1 Voltage Supply Red
2 Output 1 White
3 GND Black
4 Voltage Supply Yellow
5 Output 2 Green
6 GND Brown
Output Function
7230 Hollister Avenue
Goleta, CA 93117
www.beisensors.com
Tel: 800-350-2727
Fax: 805-968-3154
Rev 2-27-13
Loading...