Beijing MADV Technology YKQ01FJ User Manual

北京疯景科技有限公司

MADV遥控器说明书

MADV Camera Remote Control

LET’S GET STARTED

Complete user manual available at www.madv360.com/product.html

Remote Control

LCD display screen

Shutter/Confirm
button

Label button

Product name: Camera Remote Control

Product model: YKQ01FJ

Product size: 55.40×37.60×13.00mm

Weight of main part: about 45g

Working temperature: -10 — 45℃

Battery model: CR2032

Wireless connection: Bluetooth 4.1

Dust and water proofing: IP65

Sphere Camera

V1.1

2017.10.12

Battery Replacement

Power/Mode

MODE

button

Waterproof plug

Remaining recording duration

Current video resolution

Duration recorded

Press the center of rear cover to ensure

Battery

the good contact of the battery

Photo ModeVideo Mode

Remaining photo capacity

Current photo pixels

Photos taken

Battery level

Remote Control Instructions

1. Power-on/Standby
Power-on: After installing the battery, click the Power/Mode
button to switch on the remote control;
Standby: Press and hold the Power/Mode button on the right to
put the remote control in standby mode and switch off the
camera. Press any button to wake up the remote control in
standby mode. The remote control enters the standby mode.

2. Mode switching
Click the Power/Mode button when the camera is powered on,
and the remote control switches between the video and photo
modes of the camera.

3. Video recording
Click the Shutter/Confirm button when the camera is in the
video mode, and the camera begins to record video; click the
Shutter/Confirm button again, and the camera stops recording.

4. Photo taking
Click the Shutter/Confirm button when the camera is in the
photo mode, and one photograph is taken.

5. Advanced settings
Press and hold the Label button to enter the advanced settings
mode. You can check the version of the remote control,
upgrade the firmware of the remote control, switch on/off the
Wi-Fi of the camera, etc. in the advanced settings mode.

徐学翔

Connecting the Remote Control to the Camera

1. After switching on the Wi-Fi of the camera, double-click the
Wi-Fi button, and the camera enters the Bluetooth broadcasting
mode; click the Power/Mode button on the remote control to

power-on the remote control, then the camera begins to search
for and pair with the remote control.

2. If they are successfully paired, you can start to use them.

3. If they are not successfully paired, press any button to search
and pair again.

Notice for Use

This remote control for MADV Camera Remote Control is splash-proof,
waterproof and dustproof, which is tested under controlled laboratory
conditions to comply with the IP65 standard. The functions of
splash-proofing, waterproofing and dust-proofing are not permanently
effective, as the protective performance may decline due to wear
and tear in daily use. Damage caused by liquid infusion is not
under warranty coverage.
The maximum communication distance can reach 30 meters in
an open, interference-free environment.

Caution: The user is cautioned that changes or modifications
not expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.

This device complies with Part 15 of the FCC Rules and
Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appar=eils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.

NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and
receiver.

-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician
for help.

FCC& IC Radiation E
This equipment complies with FCC and Canada radiation
exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. Déclaration
d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux
radiations définies par le Canada pour des environnements
non contrôlés. Cet émetteur ne doit pas être installé au
même endroit ni utilisé avec une autre antenne ou un autre
émetteur.

xposure Statement:

SAVE THESE INSTRUCTIONS

Powered by: Beijing MADV Technology Co., Ltd.

Online support:www.madv360.com

Made in China

专色 PANTONE P 30-8C 黑色