Product Specifications
Product Name: IS-WF01
Model No.: IS-WF01
Version: 1.0
BEIJING DINGQING TECHNOLOGY, LTD
1. Introduction:
IS-WF01 is a new low-cost embedded UART-ETH-WIFI module (serial port - Ethernet -
Wireless network).
This product is an embedded module based on the universal serial interface network
standard, built-in TCP / IP protocol stack, enabling the user serial port, Ethernet, wireless
network (WIFI) interface between the conversions.
Through the IS-WF01 module, the traditional serial devices do not need to change any
configuration; data can be transmitted through the Internet network. Provide a quick solution
for the user’s serial devices to transfer data via Ethernet.
This module is mainly applied to the network camera, set-top boxes, car camera, WIFI
audio equipment. The end product which equipped with this WIFI module may at least 20cm
from the human when normal use.
BEIJING DINGQING TECHNOLOGY, LTD
2. Product information
2.1 Block diagram
2.2 Outline information
Interface and protocol
WIFI protocol
2.4GHz, 802.11b/g/n(HT20/40) Max:150Mbps
11n：135，121.5，108，81，54，40.5，27，13.5Mbps
11g：54，48，36，24，18，12，11，9，6，5.5，2 ，1 Mbps
11b： 11/5.5/2/1 Mbps
Characteristics:
WLAN
Support 64/128WEP，WPA/WPA-PSK、WPA2/WPA2-PSK、IEEE 802.1X
encryption
Support SSIDbroadcast control and access control based on MAC address
Operating channal:USA,1-11CH, UE,1-13, JP,1-14
Frequency range :2.4~2.4835GHz
Spread-spectrum technique :DSSS
Data modulation type :BPSK, QPSK, CCK and OFDM (BPSK/QPSK/16-QAM/
64-QAM)
Sensitivity @PER:54M：-68dBm@10%PER；11M：-85dBm@8% PER；6M：
-88dBm@10% PER；1M：-90dBm@8% PER；256K：-105dBm@8% PER（Typical）
Transmission distance: 100m (indoor)， 200m(outdoor)（ depend upon
different environment）
Antenna type: Chip antenna,
BEIJING DINGQING TECHNOLOGY, LTD
3. Parameters and characteristics
BEIJING DINGQING TECHNOLOGY, LTD
Software
characteristics
embedded NATfirewall with SPI，support PING、broadcast、multicast packets
filtering and MACaddress、IPaddress、URL and content filtering of domain
name。
support UPnP、DDNS functions；
support virtual server 、 DMZhost, port triggering ； support VPN ：
PPTP/IPSec/L2TP pass-through
prevent DoS attack，provide virus isolation automatically。
Built-in DHCP Server and client
Support ip and mac address binding；support ip address\PORT,MAC address
filtering and MACaddress modifying and copying 。
Offer system log and traffic statistics
Support remote and Web management，online WEB software upgrading
Specific emergency software recovery，can ultimately avoids collaps due to failture
of software upgrading
4.Environment
4.1 Temperature
4.1.1 Operating Temperature
Continuous reliable operation in ambient temperature: -10ºC to +50ºC.
4.1.2 Storage Temperature
The product is not damaged or degraded when keeping in -20ºC to +85ºC.
4.2 Humidity
4.2.1 Operating Humidity Conditions
The product should be capable of continuous reliable operation when subjected to relative humidity in
the range of 10% to 90% (non-condensing) .
4.2.2 Non-Operating Humidity Conditions (including warehouse)
The product should not be damaged or degraded when kept in the place (where relative humidity range
is in the range of 10% to 90%) for 36 hours.
BEIJING DINGQING TECHNOLOGY, LTD
5. Approvals and Certifications
RoHS and REACH process, FCC, CE undergoing.
Disclaimer
THESE MATERIALS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTYOF ANY KIND,
EITHER EXPRESS OR IMPLIED , INCLUDING BUT NOT LIMITED TO, THEIMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSEOR NON-INFRINGEMENT.
We use reasonable efforts to include accurate and up-to-date information on this document; it does not, however, make
any representations as to its accuracy or completeness of the information, text, graphics, links or other items contained
within these materials. Your use of this Document is at your own risk. Ogemaw, its suppliers, and other parties involved
in creating and delivering this Document’s contents shall not be liable for any special, indirect, incidental, or
consequential damages, including without limitation, lost revenues or lost profits.
6、OEM Labeling Requirements
USERS MANUAL OF THE END PRODUCT:
In the user's manual of the end product, the end user has to be informed to keep at least 20cm separation with the
antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency
exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this
equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required
to be available in the user's manual:
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party Responsible for compliance
could void the user’s authority to operate this equipment.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:2AB2OIS-WF01 ". If
the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available
on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
BEIJING DINGQING TECHNOLOGY, LTD
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled Environment.
This equipment should be installed and operated with minimum distance 20cm. Between the radiator &
your body.
Attention
The OEM integrator is still responsible for the FCC compliance requirement of the end product, which
integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional
equipment authorizations (e.g. Verification , Doc) of the host device to be addressed by the
integrator/manufacturer.
This RF Module does not have an own shielding, so that a Limited Modular Approval (LMA) was granted:
This RF module is strictly limited to the integration by the Grantee himself or the dedicated OEM
integrators under the control of the Grantee. and This LMA with a Integral antenna, antenna gain is
2.0dBi.
Proper measurements of the host device including this RF module (radiated spurious emissions and bandage) are
required to assure compliance with the FCC regulations.
Any other integrator must contact the Grantee to determine necessary compliance measurements and/or additional
equipment authorizations (e.g. Class II Permissive Change or New Equipment Authorization) for his
configuration. This RF Module must not be sold to the general public.
IMPORTANT NOTE: In the event that these conditions cannot be met (for example: certain laptop configurations
or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID
cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Changes or
modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Loading...