PCI2307
User’s Manual
Beijing ART Technology Development Co., Ltd.
PCI2307 Data Acquisition
Contents
Contents..............................................................................................................................................................................2
Chapter 1 Overview ...........................................................................................................................................................3
Chapter 2 Components Layout Diagram and a Brief Description.....................................................................................4
2.1 The Main Component Layout Diagram................................................................................................................4
2.2 Jumper and Interface Description.........................................................................................................................4
Chapter 3 Connection Ways for Input and Output.............................................................................................................7
3.1 Input Principle and wiring....................................................................................................................................7
3.2 Output wiring....................................................................................................................................................... 8
Chapter 4 Notes and Warranty Policy............................................................................................................................... .9
4.1 Notes ....................................................................................................................................................................9
4.2 W arranty Policy....................................................................................................................................................9
Products Rapid Installation and Self-check......................................................................................................................10
Rapid Installation..................................................................................................................................................... 10
Self-check................................................................................................................................................................. 10
Delete Wrong Installation.........................................................................................................................................10
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
2
PCI2307 Data Acquisition
Chapter 1 Overview
PCI2307 is an opto-isolator input and relay output board, mainly used for industrial control and related fields.
Unpacking Checklist
Check the shipping carton for any damage. If the shippin g carton and contents are damaged, notify the local dealer or
sales for a replacement. Retain the shipping carton and packing material for inspection by the dealer.
Check for the following items in the package. If there are any missing items, contact your local dealer or sales.
¾ PCI2307 Data Acquisition Board
¾ ART Disk
a) user’s manual (pdf)
b) drive
c) catalog
¾ Warranty Card
FEATURES
Digital Input
¾ 16-ch opto-isolated input
¾ The change of digital input channel 0 (DIO) status can make computer generates hardware interrupt, the direction
option.
¾ Input signal rate: 10KH
Z
¾
Isolation Voltage: 3750Vrms(Min.)
¾ Input Voltage: 5~24V
Digital Output
¾ 16-ch isolated relay output
¾ Each channel only has N.O. Contact, contact disconnects when power on.
¾ Switching capacity: maximum current 2A, voltage 60V
DC
/120VAC
¾ Transient Voltage: 2000V
AC
(20us)
¾ Spulenkontakt Voltage: 1500V
AC
1min
¾ Contact Capacity: 1A 24V
DC
/ 120VAC
¾ Connection Tim e: 6ms
¾ Break Time: 4ms
Board Dimension: 143mm (L)*107mm (W) *15mm (H)
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
3
PCI2307 Data Acquisition
Chapter 2 Components Layout Diagram and a Brief Description
2.1 The Main Component Layout Diagram
2.2 Jumper and Interface Description
Please refer to the first section of the main component layout diagram, to understand the general function of the
following main components.
CN1: signal input and output connector
JP1: Interrupt mode selected
1-2 shorted: Interrupt when DI0 signal has a rising edge
2-3 shorted: Interrupt when DI0 signal has a falling edge
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
4
PCI2307 Data Acquisition
62 core plug on the CN1 pin definition
42
1
22
24
23
2
3
25
4
26
5
27
6
28
7
29
8
30
9
31
10
32
11
33
12
34
13
35
14
36
15
37
16
38
17
39
18
40
19
41
20
21
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
DI1
DI2
DI4
DI0
DI3
DI5
DI6
DI7
DI8
DI9
DI10
DI11
DG1
KO2
KO3
KO4
KO1
KO0
COM15
COM14
COM13
COM12
COM11
COM10
COM9
COM8
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
DG0
DI12
DI13
DI14
DI15
KO7
KO6
KO5
KO15
KO14
KO13
KO12
KO11
KO9
KO8
KO10
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
5
PCI2307 Data Acquisition
Pin definition
Signal Name Type Definition
DI0~DI15 Input Digital signal input pins, the reference ground of DI0~DI7 is DG0,
the reference ground of DI8
KO0~KO15 Output Relay normal on contact, relay output pins
COM0~COM15 Output Relay common contact, COMi correspond with KOi
DG1 Input Digital ground, DI8~DI15 reference ground
DG0 Input Digital ground, DI0~DI7 reference ground
NC No Connection
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
6
PCI2307 Data Acquisition
Chapter 3 Connection Ways for Input and Output
3.1 Input Principle and wiring
DI0 ~ DI15 input principles are the same, the following description the DI0’s principle, the others are the same.
DI0 is the input signal. The following is the working principle of DI0: when DI0 is low-level, there is no voltage
difference between the 1 and 2 pin (than is, correspond with the DI0 and DG0) of the optocoupler U3, no internal
current, therefore the light-emitting diode is non-luminous, the internal dynatron is not on, in other words, the 3-pin and
4-pin are not connected together, the 3-pin output signal is low-level. When DI0 is high-level,
the result is contrary to
above.
DI connection as follows
switch signal
DI0
DI15
DI7
DI8
DG0
switch device
DG1
switch device
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
7
PCI2307 Data Acquisition
3.2 Output wiring
KO0 ~ KO15 is relay output, COM0 ~ COM15 its common contact.
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
8
PCI2307 Data Acquisition
Chapter 4 Notes and Warranty Policy
4.1 Notes
In our products’ packing, user can find a user manual, a PCI2307 module and a quality guarantee card. Users must
keep quality guarantee card carefully, if the products have some problems and need repairing, please send products
together with quality guarantee card to ART, we will provide good after-sale service and solve the problem as quickly
as we can.
When using PCI2307, in order to prevent the IC (chip) from electrostatic harm, please do not touch IC (chip) in the
front panel of PCI2307 module.
4.2 W arranty Policy
Thank you for choosing ART. To understand your rights and enjoy all the after-sales services we offer, please read the
following carefully.
1. Before using ART’s products please read the user manual and follow the instructions exactly. When sending in
damaged products for repair, please attach an RMA application form which can be downloaded from:
www.art-control.com.
2. All ART products come with a limited two-year warranty:
¾ The warranty period starts on the day the product is shipped from ART’s factory
¾ For products containing storage devices (hard drives, flash cards, etc.), please back up your data before sending
them for repair. ART is not responsible for any loss of data.
¾ Please ensure the use of properly licensed software with our systems. ART does not condone the use of pirated
software and will not service systems using such software. ART will not be held legally responsible for products
shipped with unlicensed software installed by the user.
3. Our repair service is not covered by ART's guarantee in the following situations:
¾ Damage caused by not following instructions in the User's Manual.
¾ Damage caused by carelessness on the user's part during product transportation.
¾ Damage caused by unsuitable storage environments (i.e. high temperatures, high humidity, or volatile chemicals).
¾ Damage from improper repair by unauthorized ART technicians.
¾ Products with altered and/or damaged serial numbers are not entitled to our service.
4. Customers are responsible for shipping costs to transport damaged products to our company or sales office.
5. To ensure the speed and quality of product repair, please download an RMA application form from our company
website.
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
9
PCI2307 Data Acquisition
Products Rapid Installation and Self-check
Rapid Installation
Product-driven procedure is the operating system adaptive installation mode. After inserting the disc, you can select the
appropriate board type on the pop-up interface, click the button【driver installation】; or select CD-ROM drive in
Resource Explorer, locate the product catalog and enter into the APP folder, and implement Setup.exe file. After the
installation, pop-up CD-ROM, shut off your computer, insert the PCI card. If it is a USB product, it can be directly
inserted into the device. When the system prompts that it finds a new hardware, you do not specify a drive path, the
operating system can automatically look up it from the system directory, and then you can complete the installation.
Self-check
At this moment, there should be installation information of the installed device in the Device Manager (when the
device does not work, you can check this item.). Open "Start -> Programs -> ART Demonstration Monitoring and
Control System -> Corresponding Board -> Advanced Testing Presentation System", the program is a standard testing
procedure. Based on the specification of Pin definition, connect the signal acquisition data and test whether AD is
normal or not. Connect the input pins to the corresponding output pins and use the testing procedure to test whether the
switch is normal or not.
Delete Wrong Installation
When you select the wrong drive, or viruses lead to driver error, you can carry out the following operations: In
Resource Explorer, open CD-ROM drive, run Others-> SUPPORT-> PCI.bat procedures, and delete the hardware
information that relevant to our boards, and then carry out the process of section I all over again, we can complete the
new installation.
BUY ONLINE at art-control.com/englishs or CALL+86-10-51289836(CN)
10
Loading...