Beijing AIQI Technology MRB1803 User Manual
Specifications
FCC Statement
Name: Mini Robot Builder
Model: MRB1803
Gross weight: 550g
Input voltage: 3V
Input current: 1.0A
Wireless connectivity: Bluetooth 4.1
Materials: ABS and PC
Ages: 6 years+
Storage temperature: -20°C ~ 45°C (-4°F ~ 113°F)
Operating temperature: -10°C ~ 45°C (14°F ~ 113°F)
Precautions
Do not dismantle the electronic components. Remove the baeries from the baery cartridge
if the product will not be used for a long time.
Do not expose the product to sunlight, fire, heat or environments where temperature is
above 60°C (140 °F).
Do not short circuit.
Do not crush or puncture.
Avoid direct sunlight. This product can be cleaned with water or a damp cloth. Please keep
the pieces clean and dry.
Regularly check for any damage to cord, plugs, enclosure and other parts. And they must not
be used until the damage has been fully repaired.
IC Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference,
and (2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) L'appareil ne
doit pas produire de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage
radioelectrique subi, meme si le brouillage est susceptible d'en compromere le fonctionnement.
CAN ICES-3(B)/NMB-3(B)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and(2) This device must accept any interference received, including interference
that may cause undesired operation.
Aention that changes or modification not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential isnallation. This product generates, uses,
and can radiate radio frequency energy and, if not installed and used in acordance with the
instructions, may cause harmful interference to radio communications, However, there is no
guarantee. that interference will not occur in a particular insallation. If this product does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diferent from that to which the receiveris
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
FCC ID: 2ALJ6-MRB1803
Manufactured by: Beijing AIQI Technology Co., LTD.
Address: Room.D1203, The11thfloor, BlockD,No.9Shangdi3rdSt.,
HaidianDistrict,Beijing, 100085, China
Made in China
Thank you for choosing the Mini Robot Builder
Mini Robot Builder User Manual
Read this manual carefully before use, and retain it for future reference
Accessories
Baery Cartridge Intelligent Brick
ONEBOT Educational Mini Robot
User Manual
Read this manual carefully before use, and retain it for future reference
Block Packs
×4
User Manual
Motors×2
Wheels×2
Baery Installation
The Mini Robot Builder requires two AA baeries. Follow the steps below to install:
The installing and uninstalling of baeries shall always be done by an adult.
Open the baery cartridge lid by pushing in the direction indicated on the lid.
Install the two AA baeries in accordance with the positive and negative polarity markings
on the boom of the baery cartridge and baeries.
Place the baery lid correctly on the baery cartridge and push the lid into place. Check
that the location hole is correctly aligned.
Align location hole
This product requires two AA baeries.
Non-rechargeable baeries cannot be recharged.
Rechargeable baeries must be charged under adult supervision.
Rechargeable baeries must be removed from the product before recharging.
Different types of baeries or new and used baeries are not to be mixed.
The supply terminals are not to be short-circuited.
Baeries must be placed according to their correct polarity.
Remove exhausted baeries from the product.
Correctly Powering On/Off
Connect the baery cartridge to the intelligent brick aer installing the baeries.
Power On: Turn on the baery cartridge, and then the intelligent brick's light is on with an
audio prompt.
Power Off: Turn off the baery cartridge, and then the intelligent brick's light is off with out
an audio prompt.
Product Overview
1. Baery Cartridge
Baery Lid Direction
Indicator
Location Hole
Switch
Magnetic PortBaery Cartridge
2. Intelligent Brick
Puzzle
Connector
Magnetic Port Restore
Controller
Master Indicator
RESET
Factory Seings
3. Device
Puzzle
Connector
Transmission
Sha
Magnetic Port
Restore
Factory Seings
Installing the Mini Robot Builder
1. Search “Mini Robot Builder” in the application store or scan the QR code below to download
Mini Robot Builder app.
Android 4.4.0 and aboveiOS 9.0 and above
2. Connect to the Mini Robot Builder.
Connect the baery cartridge and the intelligent brick. Ensure that the baeries have been
properly installed into the cartridge and turned on. Open up the Mini Robot Builder app and
turn on Bluetooth. Tap on the Bluetooth icon in the upper le corner of the main screen.
Search for discoverable Bluetooth devices, and tap on the discovered device to connect
to the Mini Robot Builder.
3. Building courses can be acquired from APP.
Loading...