Beijing AIQI Technology AIQIEDU User Manual
Specifications
Declaration of Conformity
Troubleshooting
Name: ONEBOT Educational Robot Kit
Model: AIQIEDU#01
Ages: 10+
Input voltage: 9V
Wireless connectivity: Bluetooth 4.2
Main materials: ABS、PC
Dimensions: 600×300×65mm
Gross weight: 1850g
Input current: 1.0A
Important Safeguards
Do not dismantle the intelligent brick, device, or baery cartridge. Remove the baery from the
baery cartridge if the product will not be used for a longtime.
Do not expose the product to heat fire, or ambient temperatures above 60°C.
Do not short circuit.
Do not crush or puncture.
Children aged 10-14 should only use this product under adult supervision.
Regularly check for damage to the electric cord, plugs, casing or other parts. If there is damage,
do not use the product until it has been repaired.
CHOKING HAZARD - Small parts.
Not for children under 3 years.
Manufactured by: BeijingAIQITechnologyCo.,LTD.
Address: Room.D1203,The11thfloor,BlockD,No.9Shangdi3rdSt.,HaidianDistrict,
Beijing,100085,China.
Thanks for choosing ONEBOT Educational Robot Kit
WEEE Disposal and Recycling Information Correct Disposal of this product. This marking
indicates that this product should not be disposal with other household wastes throughout
the EU.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsible to promote the sustainable reuse of materials resources.
To return your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmental
safe recycling.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Aention that changes or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this product does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
Problem Possible Cause Solution
The intelligent brick
light remains off.
Bluetooth connection failed.
The device cannot
be discovered.
The handle doesn’t
control the device.
The program does not execute.
The firmware update has failed.
Press the intelligent brick’s reset buon to restore factory seings should the above solutions prove ineffective.
Hereby,[Beijing AIQI Technology Co., Ltd. ] declares that the radio equipment type[designation of type of radio
equipment] is in compliance withDirective 2014/53/EU.
Is the controller switch turned on? Turn on the controller switch.
Is the baery out of the power? Replace with new baeries.
Are there baeries installed? Install baeries.
Is the controller switch turned on? Turn on the controller switch.
Is the baery out of the power? Replace with new baeries.
Is your phone's Bluetooth off? Turn on your phone’s Bluetooth.
Is there a good connection between
the device and intelligent brick?
Has the Bluetooth
been disconnected?
Is there a good connection between
the device and intelligent brick?
Has the Bluetooth
been disconnected?
Have you tapped the
Start buon in the app?
Is the baery out of the power? Replace with new baeries.
Are the sensor and control
board connected
Has the Bluetooth
been disconnected?
Reconnect the intelligent
brick and device.
Connect again via Bluetooth.
Reconnect the intelligent
brick and device.
Connect again via Bluetooth.
Tap the Start buon.
Reconnect the sensor to the
control board
Connect again via Bluetooth.
FCC ID: 2ALJ6-AIQIEDU
ONEBOT EDUCATIONAL ROBOT KIT User Manual
Read this manual carefully before use, and retain it for future reference
Accessories
Product Overview Installing the app
2. For detailed instructions on how to use electronic components in the
“Item List”, see the ONEBOT APP.
Block Packs
ntelligent Brick
ONEBOT EDUCATIONAL ROBOT KIT User Manual
Read this manual carefully before use, and retain it for future reference
User ManualItem List
CardboardStorage Box
1. Controller Master
2
1
Microphone
2
Indicator light
3
POWER
4
Loudspeaker
3. Baery Installation
1. Search for "ONEBOT" in the App Store or Google Play to download ONEBOT app.
( For a beer operating experience, it’s recommended to use tablet devices to install the app.)
ONEBOT Educational Robot Kit requires six AA baeries. Follow the steps below to install:
1
3
4
The installing and uninstalling of baeries shall always be done by an adult.
Open the baery cartridge lid by pushing in the direction indicated on the lid.
Install the six AA baeries in accordance with the positive and negative polarity markings on
the boom of the baery cartridge and baeries.
Place the baery lid correctly on the baery cartridge. Check that the location hole is
correctly aligned.
5
This product requires six AA baeries. Non-rechargeable baeries cannot be recharged.
Rechargeable baeries must be charged under adult supervision.
Rechargeable baeries must be removed from the product before recharging.
Do not use different manufacturers’ or new/old baeries together. Do not allow the power supply
to short circuit the device.
Baeries must be placed according to their correct polarity. Remove exhausted baeries from
the product.
6
8
2. Connecting to the ONEBOT Educational Robot Kit
Properly install the baery in the baery case and turn on the switch, open the
ONEBOT APP, turn on the Bluetooth function, click the Bluetooth icon buon in
the upper le corner of the main screen, search for Bluetooth devices, select
device, and connect to the ONEBOT Educational Robot Kit.
Bluetooth Seings
Bluetooth connection status
Bluetooth is not connected
Assembling
7
5
Motor interface/Data expansion port
6
Assembling hole
7
Reset
8
Baery Cover
1. Before you start
Ensure that you have organized your Blocks into the Storage Box.
2. Build with blocks
Please refer to the app’s Dynamic Build Manual for more information on building with the ONEBOT
Educational Robot Kit.
3. Inspect your robot
Programming
handle
Make sure you have installed baeries in the controller.
Make sure you followed the building instruction.
Make sure the controller switch is on and the indicator light of the controller is on.
Sensor
User Guide
Loading...