無線滑鼠 Wireless Mouse EMPREX
MM998888UULL IIIIII QQuuiicckk IInnssttaallllaattiioonn GGuuiiddee
Hardware Installation
1. Plug the receiver connector into your available USB port on PC.
2. Make sure the batteries of the mouse are installed correctly, please follow the
polarity signs in the battery compartment.
3. Please make sure the slide switch on the back of the mouse is switched to
“on” before using the mouse. When not in use, please turn the power switch
to “off” for power saving.
Change the cursor pointer speed
You can modify the mouse pointer speed settings in the control panel.
1. Open the Start Menu by clicking “Start” at the lower-left corner on the screen
2. Then click on Settings / Control Panel / Mouse
3. In the Mouse Properties window that appears, click the Motion tab
4. Move the slide bar toward either the faster end or the slower end
5. Click OK to exit and make the change effective
Pairing Procedure
The wireless mouse can operate out of the box immediately after you plug the receiver USB
connector into your PC USB port. If it can’t work, please follow the steps below to process ID setting
of the wireless mouse.
The pairing button locates on the top of the receiver with a LED under to show the pairing or data
reception status.
1. Press and hold the ID pairing/connect button on the top of the dongle receiver at least 2
seconds until the receiver LED flashes. The receiver LED will flash 60 seconds to wait for mouse
pairing information. (If you release the button within 2 seconds, the ID doesn’t make any
changes.)
2. Hold the mouse close to the dongle receiver within 1M.
3. Press and hold the mouse ID pairing/connect button on the bottom of the mouse at least 2
seconds until the battery low indicator flashes once. (If you release the button within 2
seconds, the ID pairing will fail.)
Pairing button on the top of the receiver
(With an LED under the pairing button)
Note:
1. Y our PC must be turne d on be fore doing this pairing pro cedure .
2. You must follow the procedure above to complete ID pairing.
3. The whole procedure should be completed within 60 seconds.
4. You don’t have to pair ID again after changing batteries.
5. The mouse can operate freely up to 10 meter from the receiver.
6. Mouse battery life is up to 9 months. It depends on the intensity of usage.
Power Sw itch
Connect Butt on
Pairing button on the bottom of t he mouse
LED indicator
(A red LED
under the sc roll
wheel)
無線滑鼠 Wireless Mouse EMPREX
System Requirements
- Available USB port
- Microsoft® Windows® ME, Windows® 2000, Windows® XP and Windows Vista® operating
system
Usage Information
- This laser mouse can work on most surfaces, including polished or wood-grain surfaces.
- While functioning, this mouse emits invisible laser light that may be hazardous to eyes. Avoid
looking directly into the emitter hole on the bottom of the mouse.
Battery Information
1. We recommend using alkaline batteries for a longer battery life.
2. Always change batteries when battery low alarm appears, otherwise the mouse will shut
down once the battery voltage is too low.
3. Don't mix different types of batteries or new and old batteries together. Always replace old
batteries with new and same type batteries.
4. Remove batteries after long periods of non-use. Battery leakage or corrosion may damage
the device quality and cause danger.
Battery Low Alarm
When the mouse battery is low, the RED LED indicator under mouse scroll wheel will flash
when the mouse is moved. Please change batteries immediately when the RED LED indicator
flashes to ensure the good use of this mouse. After you change the batteries, the RED LED
indication will disappear.
Laser Safety Information
This product complies with International Standards EN 60825-1/A2: 2001, Class 1 Laser Product, and
also complies with FDA standards Title 21 CFR 1040.10 and 1040.11, except for deviations pursuant to
Laser Notice No.50, dated June 24, 2007.
無線滑鼠 Wireless Mouse EMPREX
設定鍵
M988UL III 快速安裝指南
硬體安裝
1. 將接收器連接到電腦上，接收器的接頭連接到電腦的連接埠。
2. 安裝鍵盤的電池，並請注意電池正負極方向。
3. 請先確定滑鼠底部的電源開關已切換至”啟動(on)”的狀態之後方可使用此滑鼠。當您
不使用滑鼠時可將電源開關切換至”關閉(off)”以節省電池電量。
改變游標速度
您可以在控製台修改滑鼠游標速度的設定。
1. 點擊螢幕左下方的”開始”
2. 依序點擊設定/ 控制台/ 滑鼠
3. 點擊滑鼠內容視窗內的”移動”
4. 調整滑鼠游標移動速度
5. 點擊OK離開視窗同時完成設定
ID設定程序
當您將接收器的 USB 連接頭插入電腦的USB 連接埠之後即可立即使用此無線滑鼠。如果滑鼠無法正常運作的
話，請依照下列的步驟重新設定 ID。
位在接收器上方的 LED 燈就是接收器的 ID 設定鍵，此 LED 燈會顯示 ID 設定或訊號接收的狀態。
1. 先按一次接收器上方的ID設定鍵。 此時接收器ID設定鍵下方的LED燈會緩慢閃爍以表示它已準備好接收
滑鼠的設定訊號。
2. 然後請按一次滑鼠底部的ID設定鍵。
3. 此時接收器的LED燈會快速閃爍3次以表示它已接收到滑鼠的設定訊號。
4. 當您移動滑鼠時，接收器的LED燈會持續閃爍。當您停止使用滑鼠時，接收器的LED燈會熄滅。
接收器上方ID 設定鍵
(ID 設定鍵下方有LED 鍵)
注意:
1. 電腦為開機狀態下，才可設定ID。
2. 每組ID設定的過程需在60秒之內完成。
3. 更換電池之後不需重設ID 即可繼續使用此無線滑鼠。如果無法正常使用，請按照上述的步驟重新設定此
無線滑鼠的ID。
4. 此無線滑鼠距接收器的有效操作距離可達10公尺。
5. 滑鼠電池壽命可達2.5個月，視使用頻率而定。
電源開關
ID
滑鼠底部ID設定鍵
LED 燈 (在滑鼠
下方有紅色的
LED 燈)
系統需求
- 可用的 USB 連接埠
- Microsoft® Windows® ME, Windows® 2000, Windows® XP or Windows Vista® 作業系統
無線滑鼠 Wireless Mouse EMPREX
使用須知
- 此雷射滑鼠可在大多數表面使用，包括光澤的表面和木頭材質表面。
- 當此滑鼠處於作用狀態時會放射可能傷害眼睛的不可見雷射光束。避免直視滑鼠底部的發射孔。
電池資訊
1. 我們建議使用鹼性電池以獲得較佳的使用效能。
2. 請在低電量警示出現時立即更換電池。
3. 勿將型號不同、或者是新舊不一的電池混合使用。請用型號相同且全新的電池來更換舊電池。
4. 如長時間不使用滑鼠，請將電池槽中的電池取出，以免因電池漏液或生鏽而造成滑鼠損毀。
電池低電量警示:
若您移動滑鼠的時候發現滾輪下方紅色的LED指示燈不斷閃爍的話，即表示滑鼠電池電量過低。請立即
更換滑鼠電池以確保您可正常使用此滑鼠。當您更換新電池之後，滾輪下方紅色的LED指示燈即會停止
閃爍。
雷射安全資訊
本產品符合國際標準EN 60825-1:2001/A2:2001一級雷射產品性質之標準，亦符合FDA Title 21 CFR 1040.10
及1040.11標準，除 FDA 2007年6月24日公告Laser Notice No. 50之差異事項外(deviations pursuant to
Laser Notice No. 50 dated June 24, 2007)。
根據交通部低功率管理辦法規定:
第十二條 經型式認證合格之低功率射頻電機，非經許可、公司、商號或使用者
均不得擅自變更頻率，加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信:經發現有干
擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
無線滑鼠 Wireless Mouse EMPREX
前
項
合
法
通
信
，指
依
電
信
規
定
作
業
之
無
線
電
信
。低
功
率
射
頻
電
機
須
忍
受
合
法
通
信
或
工
業
無線滑鼠 Wireless Mouse EMPREX
FCC GUIDELINES
This equipment h as been tested and foun d to comply with the limits for a Cl ass B digital device, pursu ant to Par t 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installatio n. This equipmen t generates, uses and can r adiate radio frequency energy and, if no t installed and used in
accordance with the instru ctions may cause ha rmful interference to radio commun ications. However, ther e is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or tel evision recep tion, which can be d etermined by turn ing the equipmen t off and on, the user is
encouraged to try to correct the inter ference by one or more of the follo wing measures:
Reorient or relocate the receiving antenna.
Increase the separ ation between the equ ipment and receiv er.
Connect the equipmen t into an outl et on a circuit di fferent from that to whi ch the receiver is co nnected.
Consult the dealer or an experienced radio/TV technici an for help.
Use only shiel ded cables to conn ect I/O devices to this equipment.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may no t cause harmful in terference, (2) this device must a ccept any interfer ence received, inclu ding
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expr essly approv ed by the party r esponsible for compliance cou ld
void the user's a uthority to o perate this equi pment.
Information to user:
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes
or modificati ons not expressly approved by the party respo nsible for comp liance coul d void the user ’s authority to
operate the equi pment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying RF exposure compliance.
This transmitter mu st not be co-loca ted or operatin g in conjuncti on with any o ther antenna or transmitter.
產品規格：
Specifications:
頻率範圍: 2402MHz-2479 MHz
滑鼠 Output power: 86.65 dBm
接受器 Output power: 89.67 dBm
低功率電波輻射性電機管理辦法：
第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特
性及功能。
第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得
繼續使用。
前項合法通信，指依電信法規定作業之無線電信。
低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Do not litter
3100508110 Version 1.0 Aug. 2008 Printed in China
Loading...