Behavior Tech Computer MS5213URF2, KB5213URF2, RX5213URF2 User Manual

5213URF2

Wireless Keyboard & Mouse Kit

Manual

Version 1.0

FCC GUIDELINES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

s Reorient or relocate the receiving antenna
s Increase the separation between the equipment and receiver
s Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
s Consult the dealer or an experienced radio/TV technician for help.

The Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation.
Cet appareil numerique de la class B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference. (2) This device must accept any interference received, including interference that
may cause undesired operation.

This equipment is intended for use in the following countries EU 15 countries:
Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, Luxembourg, Netherlands, Spain, Sweden, United
Kingdom, Portugal, Greece. And other non-EU countries: Switzerland, Norway, and Iceland.

低功率電波輻射性電機管理辦法：

第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原

第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干

設計之特性及功能。

擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電信。

低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. Shielded interface cable, if any, must be used in order to comply with emission
limits.

The information in this document is subject to change without notice and does not represent a commitment on the part
of the vendor.

No warranty of representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for
any particular purpose of this document. The manufacturer reserves the right to make changes to the content of this
document and/or the products associated with it at any time without obligation to notify any person or organisation of
such changes.

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising out of
the use or inability to use this product or documentation, even if advised of the possibility of such damages.

Copyright © 2003. All rights reserved

IBM, PC/AT and PS/2 are registered trademarks of International Business Machines Corporation.

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the United States of
America and/or other countries.

All other trademarks are trademarks of their respective holders.

1

Table of Contents

Important Information..................................................................................................2

1 Battery Installation............................................................................................2

2 Receiver cable positioning..............................................................................2

1 Introduction...........................................................................................................3

What's in this package.............................................................................................3

2 System Requirements..........................................................................................4

3 Hardware Installation...........................................................................................5

3.1 Connecting and Battery Information .......................................................5

3.2 ID Setting ......................................................................................................6

3.3 Battery Low Indication ...............................................................................7

4 Using the Keyboard..............................................................................................8

5 Troubleshooting....................................................................................................9

2

Don't intertwine receiver cable with power

Important Information

1 Battery Installation

When battery power gets too low, the computer will
display a battery low icon on the system tray or flash
10 seconds every minute on right upper screen as
notification.

1.1 Open the battery compartment cover on the
bottom of the keyboard and mouse.

1.2 Follow the indication inside to place in keyboard
and mouse batteries.

1.3 Place the battery compartment cover back and
proceed with ID setting of the devices.

Important:

Ø We recommend using alkaline batteries for a

longer battery life.

Ø Always change batteries when battery low icon

appears.

Ø Install keyboard and mouse driver first to

ensure the battery power is monitored.

Ø Don't mix different types of batteries or new

and old batteries together. Always replace old
batteries with new and same type batteries.

Ø Remove batteries after long periods of

non-use. Battery leakage or corrosion may
damage the device quality and cause danger.

2 Receiver cable positioning

2.1 Don't warp receiver cable around monitor

or LCD panel base.

2.2

cables.

2.3 Don't bundle or bind receiver cable with

other signal cables.

2.4 Don't extend receiver cable unless

absolutely necessary, and let receiver
cable run free from other cables.