Behavior Tech Computer KB9128URF2, MS9128URF2, RX9128URF2 User Manual

9128URF Ⅱ

Wireless Office Desktop

Manual

Battery Installation

Important Information

When battery power gets too low, please change keyboard or mouse batteries according to following instructions:

1. Open the battery compartment cover on the bottom of the keyboard and mouse.

2. Follow the indication inside to place in keyboard and mouse batteries.

3. Place the battery compartment cover back and proceed with ID setting of the devices.

Important:

Ø We recommend using alkaline batteries for a longer battery life.

Ø Always change batteries when battery low icon appears.

Ø Install keyboard and mouse driver first to ensure the battery

power is monitored.

Ø Don't mix different types of batteries or new and old batteries

together. Always replace old batteries with new and same type batteries.

Ø Remove batteries after long periods of non-use. Battery

leakage or corrosion may damage the device quality and cause danger.

Receiver cable positioning

1. Don't warp receiver cable around monitor or LCD panel base.

2. Don't intertwine receiver cable with power cables.

3. Don't bundle or bind receiver cable with other signal cables.

4. Don't extend receiver cable unless absolutely necessary, and let receiver cable run free from other cables.

Introduction

Congratulations on your purchase of this wireless RF keyboard and mouse! This keyboard and mouse will finally free you of the constraints of your desktop by providing a wireless connection between your keyboard/mouse and your PC. Pass around the keyboard or mouse during meetings without having to bother about a cable blocking your way or write e-mails and surf the Internet from the comfort of your living room couch!

This keyboard and mouse kit consists of a keyboard, a mouse and a receiver. The receiver is connected to your PC through a cable with both a keyboard and mouse connector. The keyboard and mouse can operate freely within a radius of at least 3.28 feet (about 1 meter) from the receiver, which itself has a maximum range from your PC of around 3.28 feet (about 1 meter). Because the keyboard and mouse use radio frequencies to transmit the wireless signal, it has no constrictions on viewing angles such as with infrared devices like your TV’s remote control, etc.

Besides providing unprecedented freedom of movement when operating the keyboard or mouse, the kit also offers more extra functionality by introducing dedicated buttons for often used Internet browser functions. (Please note: The Internet keys work only under Microsoftâ Internet Explorer

5.0 or later version!).

In order to enjoy your keyboard and mouse to their full potential we recommended you read this manual carefully prior to installation.

What's in this package

w A Wireless keyboard with palmrest

w A Wireless mouse

w A Receiver

w A Driver CD with Manual

w Batteries (4 pcs of AA alkaline batteries)

System Requirements

w Microsoftâ Windowsâ 95, Windowsâ 98SE, Windowsâ ME, Windowsâ 2000 or

Windows XP operating system

w Microsoftâ Internet Explorer 5.0 or later version (for the Internet keys)

w CD-ROM drive (for CD and Video operation)

w Standard sound card (for CD and Video operation)

w Available PS/2 & USB port.

Please refer to table below for the other system requirements for the features.

Operating System

Function Description

Windows 95 / Windows 98

Windows ME / Windows 2000 / Windows XP

Wireless Functionality

Keyboard Extra Hotkey Functions

Keyboard Battery Low Indication

Mouse Battery Low Indication

F-Lock Key Function

Available immediately after hardware installation

Driver is need for activated these hotkey functions

Available immediately after hardware installation (**)

Driver is need for activated these hotkey functions (***)

Available immediately after hardware installation

Available immediately after hardware installation (*)

Available immediately after hardware installation (**)

Driver is need for activated these hotkey functions (***)

(*): Driver is still needed for Word, Excel, and PowerPoint.

(**)

1. The flashing LED on receiver or under mouse scroll wheel shows keyboard or mouse battery

low indication.

2. After the driver installed, there will be a battery low icon or appears on Windows system

tray besides KeyMaestro Driver icon .

(***): After the driver is installed, the default status of F-Lock Key is disabled when you plug the

receiver connector into your PC. Press it again to make the Enhanced Function (F1-F12) keys start Office functions. Please refer to P.9 for more information.

Bottom View of Mouse

Hardware Installation

Ø Connecting and Battery Information

w For USB Model:

Just directly plug the receiver’s USB connector into PC USB port.

Front View of USB Connector

1. Take the keyboard and make sure the batteries on the back are installed correctly. (Follow the polarity signs in the battery compartment.)

Bottom View of Keyboard

2. Take the mouse and make sure the batteries on the back are installed correctly. (Follow the polarity signs in the battery compartment.)

3. Turn on your PC, and PC system would auto-detective this RF keyboard kit.

Remarks:

1. Both the keyboard and mouse use 2pcs standard UM-3 (AA) 1.5V alkaline batteries.

2. Keyboard battery life is about 2-3 months, and mouse battery life is about 1-1.5 months, depending on the intensity of usage.

3. Make sure the receiver is placed in a location relatively free of strong electromagnetic or transmission sources in order to ensure optimal reception of the keyboard and mouse signal.

Ø Detachable Palmrest

At your discretion, you may choose to connect the palmrest with keyboard.

Detach the palmrest from up to down (↓) direction, when the palmrest is set, a click sound would be heard.

Ø ID Setting

This wireless optical mouse contains 256 sets ID. The ID-recognition function helps to protect against interference from other RF products in the same environment. Remember to reset ID when other RF products affect your keyboard kit.

w The ID button locates on the top of the receiver with a LED under to show the

connecting condition.

w The mouse should be able to work after you first install it. If it can’t work, please follow

the steps below to process ID setting of this mouse.

1. Firstly, press the ID button on the bottom of the mouse once.

Mouse ID button

+ 14 hidden pages