Wireless Mouse & Keyboard & Receiver
f
9089URF III / EMPREX
9089URF III Quick Installation Guide
Important Information
- For Windo ws® 2000 operating system, please go to http://www.emprex.com/ website to download and install the “KeyMaestro
Input Device Driver” to have the Multimedia Player functions.
- For Windows® XP and W indows Vista® operating systems, you could use the keyboard immediately after plugging the keyboard
connector into the PC. If you want to enjoy the full functionality of the keyboard, please visit our website at
http://www.emprex.com/
hot keys are reprogrammable. They can be configured as a string, a combin ation key, a web site, an existing file, or a function
that the driver pre-defines for you.
Hardware Installation
1. Make sure the batteries of the keyboard and mouse are installed correctly. Please follow
the polarity signs in the battery compartment.
2. Please make sure the power switch on the back of the mouse is switched to “on” before
using the mouse. When not in use, please turn the power switch to “off” for power saving.
3. Plug the dongle receiver connector into your available USB port on PC.
4. Please hold the keyboard and mouse close to the receiver within 30 cm and press any key
to pair ID.
Change the Cur sor Pointer Speed
You can modify the mouse pointer speed settings in the control panel.
1. Open the Start Menu by clicking “Start” at the lower-left corner on the screen
2. Then click on Settings / Contr ol Panel / Mouse
3. In the Mouse Properties window that appears, click the Motion tab
4. Move the slide bar toward either the faster end or the slower end
5. Click OK to exit and make the change effectiv e
ID Pairing Procedure
You could use the keyboard immediately after pluggi ng the receiver into PC. If it can’t work,
please follow the steps below to process the ID pairing procedure.
ID pairing procedures:
1. Press and hold the ID pairing/connect button on the top of the dongle receiver at least 2
seconds until the receiver LED flashes. The receiver LED will flash 60 seconds to wait for
keyboard and mouse pairing i nformation. (If you release the button within 2 seconds,
the ID pairing will fail.)
2. Hold the keyboard and mouse close to the dongle receiver within 30 cm.
3. Press and hold the keyboard ID pairing/connect button on t he bottom of the keyboard at
least 2 seconds until the keyboard LED, which is on the upper right of the keyboard,
flashes once. (If you release the button within 2 se conds, the ID pairing will fail.)
4. Press and hold the mouse ID pairing/connect button on the bottom of the mouse at least 2
seconds until the battery low indicator flashes once. (If you release the button within 2
seconds, the ID pairing will fail.)
Note:
- Each procedure should be com pleted within 60 seconds.
- Make sure your PC is on and running when doing the pairing procedure.
- You don’t have to pair ID again after changing batteries. If it can’t work, please follow the
steps above to pair ID.
-
Both the keyboard and mouse can operate freely up to a radius of about 10m from the
receiver.
- Keyboard battery life is up to 15 m onths and mouse battery life is up to 9 mont hs. It
depends on the intensity of usage.
System Requirements
Available USB port
CD-ROM drive (for CD and Video operation)
Standard sound card (for CD and Video operation)
Microsoft® Internet Explorer 5.0 or later version (for the Internet keys)
Microsoft® Windows® 2000, Windows® XP or Windows Vista® operating system
Driver Installation
USB Device Driver
The USB device driver is included with your Windows operating system.
During the initi al installation of the keyboard USB device, the system will automatically detect that a new hard ware device has been
added and will bring up the "Add New Hardware Wizard" dialogue box. Follow the Wizard's USB driver installation steps. Once this
installation step is completed, the basic functions of the USB device wi ll work under the operating system. The additional functions
are provided only after the KeyMaestro driver is installed.
KeyMaestro Input Device Driver
1. After you download the driver, please find the “Setup Key.exe” in the directory and double-click this file.
2. Follow the on-scr een instructions to install the driver.
3.
The driver icon
to download and install the “KeyMaestro Input Device Driver.” Once the driver has been installed, these
will show at the bottom right of the W indows system tray when the driver is loaded.
/ BTC
Front view of Back view of
USB connector USB connector
ID pairing/connect button on the top o
the dongle receiver
(With a LED indicator under the ID
pairing/connect button)
Power Switch
ID Pairing Button/
Connect button
ID Pairi ng /connec t butto n on the
bottom of the mous e
ID pairing /connect button on the
bottom of the keyb oard
English
Wireless Mouse & Keyboard & Receiver
9089URF III / EMPREX
Important Usage Information
English
Battery:
1. We recommend using alkaline batteries for a longer battery life.
2. Always change batteries when battery low alarm appears, otherwise the mouse or keyboard will shut down once the battery
voltage is too low.
3. Don't mix different types of batteries or new and old batteries together. Always replace old batteries with new and same type
batteries.
4. Remove batteries after long periods of non-use. Battery leakage or corrosion may damage the device quality and cause
danger.
5. Keyboard battery life is up to 15 months and mouse battery life is up to 9 mo nths. It depends on the intensity of usage.
Battery Low Alarm:
1.
Mouse battery low alarm:
- When the mouse battery is low, the RED LED indicator under mouse scroll wheel will blink when the mouse is moved.
Please change batteries immediately when the RED LED indicator lights up to ensure the good use of this mouse. After you
change the batteries, the RED LED indicator will disappear.
2. Keyboard battery low alarm:
- When the keyboard battery is low, the RED LED indicator, which is on the upper right of the keyboard, will blink when you
press keyboard buttons. Please change batteries immediately when the RED LED indicator ligh ts up to ensure the good use
of this keyboard. After you change the batteries, the RED LED indicator will disappear.
Mouse usage:
1. This laser mouse can work on most surfaces, includi ng polished or wood-grain surfaces.
2. While functioning, this mouse emits invisible laser light that may be hazardous to eyes. Avoid looking directly into the emi tter
hole on the bottom of the mous e.
Laser Safety Information
This product complies with International Standards EN 60825-1/A2: 2001, Class 1 Laser Prod uct, and also complies with FDA
standards Title 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No.50, dated June 24, 2007.
/ BTC
Wireless Mouse & Keyboard & Receiver
9089URF III / EMPREX
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment.
FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
Information to user:
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes
or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users
must follow the specific operating instructions for satisfying RF exposure compliance.
FCC GUIDELINES
/ BTC
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Do not litter
Wireless Mouse & Keyboard & Receiver
設
定鍵
9089URF III / EMPREX
9089URF III
重要資訊
- 若您為
- 若您為
Windows
媒體播放鍵的功能。
Windows® XP 和 Windows Vista®
享有更多的快捷鍵功能，請至
成之後，所有快捷鍵的功能都是可以更改的。您可以更改功能為一個字串、複合功能鍵、網址、檔案、或是由程式預設的
功能。
硬體安裝
1.
安裝鍵盤和滑鼠的電池，並請注意電池正負極方向。
2.
使用滑鼠時，請先確定滑鼠底部的電源開關已經切換至"開啟
若不使用滑鼠時，您可將電源開關切換至"關閉
3.
將接收器連接到電腦上，接收器的接頭連接到電腦的連接埠。
4.
當您將接收器的
收器，在距離30公分以內按任一鍵來設定ID。
改變游標速度
您可以在控製台修改滑鼠游標速度的設定。
1.
點擊螢幕左下方的”開始
2.
依序點擊設定/ 控制台/ 滑鼠
3.
點擊滑鼠內容視窗內的”移動
4.
調整滑鼠游標移動速度
5. 點擊OK
ID 設定程序
當您將接收器的
組。如果此無線鍵盤滑鼠組無法正常運作的話，請依照下列的步驟重新設定ID。
ID 設定程序:
1.
請按壓接收器上方的ID設定鍵至
接收器的
您沒有按壓ID設定鍵至少
2.
鍵盤和滑鼠必須靠近接收器30公分以內。
3.
請按壓鍵盤底部的ID設定鍵至少
之後再放手。(若您沒有按壓ID設定鍵至少
4.
請按壓滑鼠底部的ID設定鍵至少
再放手。(若您沒有按壓ID設定鍵至少
注意：
- 每組ID設定的過程需在60秒之內完成。
- 電腦為開機狀態下，才可設定ID。
- 更換電池之後不需重設
按照上述的步驟重新設定此無線鍵盤滑鼠組的ID。
- 此無線鍵盤及滑鼠距接收器的有效操作距離可達10公尺。
-
鍵盤電池壽命可達15個月，滑鼠電池壽命可達9個月，視使用頻率而定。
®
2000
使用者，請至
http://www.emprex.com/
USB
連接頭插入電腦的
”
”
離開視窗同時完成設定
LED
USB
連接頭插入電腦的
會緩慢閃爍60秒 以表示它已準備好接收鍵盤和滑鼠的設定訊號。(若
2
秒
ID
即可繼續使用此無線鍵盤滑鼠組。 如果無法正常使用，請
http://www.emprex.com/
使用者，當您將鍵盤的連接頭連接到電腦之後，即可立即使用此鍵盤。若您想
(off)"
USB
連接埠之後，請將鍵盤和滑鼠靠近接
USB
連接埠之後即可立即使用此無線鍵盤滑鼠
2 秒，一直到接收器的
，則無法設定ID。
2 秒，一直到位於鍵盤右上角的
2 秒，一直到位於滑鼠上方的
2
)
2
秒
，則無法設定ID。
秒
，則無法設定ID。
快速安裝指南
下載並安裝「
下載並安裝「
(on)"
以節省電池電量。
LED
閃爍之後再放手。此時
LED
)
LED
)
之後才可使用。
燈閃爍一次之後
/ BTC
KeyMaestro
KeyMaestro
燈閃爍1次
輸入裝置驅動程式」以使用多
輸入裝置驅動程式」。驅動程式安裝完
USB 連接頭正面圖 USB 連接頭背面圖
接收器上方 ID 設定鍵
(ID 設定鍵下方有 LED 燈)
ID
電源開關
滑鼠底部 ID 設定鍵
鍵盤底部ID設定鍵
系統需求
可用的
音效卡（播放音樂片與影音光碟片之用）
USB
光碟機（播放音樂片與影音光碟片之用）
Microsoft® Internet Explorer 5.0
Microsoft® Windows® 2000, Windows® XP 或 Windows Vista®
連接埠
以上版本（網際網路鍵之用）
作業系統
安裝驅動程式
USB 裝置驅動程式
USB
裝置驅動程式已附在
首次安裝
動程式的指示完成安裝步驟。安裝步驟完成後即可使用
方可使用。
KeyMaestro 輸入裝置驅動程式
1. 當您下載完驅動程式之後，請雙擊根目錄中的"SetupKey.exe"檔案。
2.
3.
USB
裝置時，系統會自動偵測新增硬體然後跳出「
依螢幕指示完成安裝步驟。
當驅動程示的圖示
Windows
出現在右下角的工作列上時，即表示驅動程式載入成功。
操作系統中。
Add New Hardware Wizard
USB
裝置的基本功能。其他的附加功能則需等到應用程式安裝完成後
」對話框。請依照
Wizard USB
驅
Wireless Mouse & Keyboard & Receiver
9089URF III / EMPREX
產品規格：
Specifications:
鍵盤 Output power: 95.04dBi
滑鼠 Output power: 88.92 dBi
低功率電波輻射性電機管理辦法：
第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更
第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無
電池:
1. 我們建議使用鹼性電池以獲得較佳的使用效能。
2.
3. 勿將型號不同、或者是新舊不一的電池混合使用。請用型號相同且全新的電池來更換舊電池。
4. 如長時間不使用鍵盤或滑鼠，請將電池槽中的電池取出，以免因電池漏液或生鏽而造成鍵盤或滑鼠損毀。
5. 鍵盤電池壽命可達 15 個月，滑鼠電池壽命可達 9 個月，視使用頻率而定。
1.
2.
滑鼠使用須知
1. 此雷射滑鼠可於大多數表面使用，包括光滑的表面和木頭材質表面。
2. 當此滑鼠處於作用狀態時會散發可能傷害眼睛的不可見雷射光束。避免直視滑鼠底部的發射孔。
雷射安全資訊
頻率範圍
接受器
: 2402MHz-2479 MHz
Output power: 98.35 dBi
原設計之特性及功能。
干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電信。
低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
請在低電量警示出現時立即更換電池。當電池電量過低時，鍵盤或滑鼠會直接斷電而無法繼續使用。
電池低電量警示:
滑鼠電池低電量警示
- 若您移動滑鼠的時候發現滾輪下方紅色的 LED 指示燈不斷閃爍的話，即表示滑鼠電池電量過低。請立即更換滑鼠電池以確保
您可正常使用此滑鼠。當您更換新電池之後，滾輪下方紅色的
鍵盤電池低電量警示
- 當您按鍵時發現鍵盤右上角的紅色 LED 指示燈不斷閃爍的話，即表示鍵盤電池電量過低。請立即更換鍵盤電池以確保您可正
常使用此鍵盤。當您更換新電池之後，鍵盤右上角的紅色
本產品符合國際標準
除 FDA 2007 年 6 月 24 日公告 Laser Notice No. 50 之差異事項外(deviations pursuant to Laser Notice No. 50 dated June 24,
2007)。
:
:
:
EN 60825-1:2001/A2:2001
指示燈即會停止閃爍。
LED
指示燈即會停止閃爍。
LED
一級雷射產品性質之標準，亦符合
/ BTC
FDA Title 21 CFR 1040.10及1040.11
標準，
Loading...