Behavior Tech Computer KB9039ARF3, RX9039ARF3 User Manual

Wireless Keyboard & USB dongle /9039ARF III / BTC / EMPREX

Hardware Installation

Quick Installation Guide

1. Plug the dongle receiver connector into your available USB port on PC.

2. Make sure the batteries of the keyboard are installed correctly. Please follow the polarity signs in the battery compartment.

Note: After you plug the receiver USB connector into your PC USB port, pleas e hold the keyboard close to the receiver within 1m and press any key to pair ID.

ID Pairing Procedure

If it can’t work, please follow the steps below to process the ID pairing procedures. The ID-recognition function helps to protect against interference from other RF products. products affect your keyboard kit.  ID pairing/connect button location:

- Receiver ID pairing/connect button→ on the top of the

- Keyboard ID pairing/connect button→ on the bottom of the

 ID pairing procedures:

1. Press and hold the ID pairing/connect button on the top of the dongle

2. Hold the keyboard close to the dongle receiver within 1M.

3. Press and hold the keyboard ID pairing/connect button on the bottom of the

4. The receiver LED indicator flashes rapidly as its ID paired with this keyboard.

Note:

- The whole ID pairing procedure shall be completed within

- Make sure your PC is on and running when doing the

- You don’t have to pair ID again after changing batteries. If it

- The keyboard can operate freely up to a radius of abo ut

- The keyboard battery life is up to 4.5 months.

Remember to follow the steps below to change ID when other RF

dongle receiver

keyboard

receiver about 5 seconds until the receiver LE D flashes. The receiver LE D will flash 60 seconds to wait for keyboard pairing information. (If you release the button within 5 seconds, the ID doesn’t make any changes.)

keyboard about 5 seconds until the keyboard LED flashes. (If you release the button within 5 seconds, the ID pairing will fail.)

Then you could press any key to check if the keyboard works or not.

60 seconds.

pairing procedure.

can’t work, please follow the steps above to pair ID. 10m from the receiver.

Front View of

ID pairing/connect button on the top of the

Back View of

ID LED/

Low

Batter

Keyboard Hotkey Functions (from left to right)

1. MCE Start

Button

2. Mouse

Painter

3. Li ve TV

4. Guide

5. DVD

6. Volume -

7. Volume+

To quickly launch Media Center

Built-in mouse painter and Left/Right click.

Switch to Live TV to bring up Live TV on your computer screen or on a television connected to your Media Center PC. Go to the electronic programming guide.

Display the DVD menu

Adjust the volume

9. Back

10. More

11. Record

12. Play

13. Pause

14. Stop

15. Rew/Fwd

16. Replay

Go to the previous screen.

Show information about the selected item. Record the TV Show to disk. Play the selected song, album, play list, recorded TV Show, or video. Pause the currently playing media. Press pause again to resume. Stop the currently playing media. Press play to start the track again from the beginning. Rewind/ Speed up the currently playing media. Rewind the position pointer and

Wireless Keyboard & USB dongle /9039ARF III / BTC / EMPREX

(Previous) Increment

8. Mute

Mute the sound without stopping play back

17. Skip (Next)

Skip ahead an increment.

Power Key

Power Button 2. ID LED /Battery low indicator

Depending on your system power management setting, this button can be used to shut the PC

down or put the PC into standby (sleep) mode or wakes it up from standby

Battery Low Alarm

When the keyboard batteries are low, the RED LED indicator, which is on the upper right of the keyboard, will blink when you press keyboard

buttons. Please change batteries immediately when the RED LED indicator ligh ts up to ensure the good use of this ke yboard. After you change

the batteries, the RED LED indicator will disappear.

System Requirement

 Microsoft® Windows 7™ (Home Premium or above), Windows Vista™ (Ultimate/Home Premium) or Windows® XP Media Center Edition 2005

or later.

 CD-ROM drive (for CD and Video operation)  Standard sound card (for CD and Video operation)

+ 1 hidden pages