Page 1
2
3
4
5
1
6
7
BEHA ELEKTRO AS
N-3940 PORSGRUNN, Norway
post@beha.no - www.beha.no
The system controls BEHA Convector Panel Heaters type P
and L. In additionto the iJaz Central Control Unit each heater
needs a RP 200 Radio Plug for wireless communication
between the central control unit and the heater. A wireless
switch (SP 16) for switching on and off other appliances like
lights, coffee maker, hotwater tank etc. isavailable. The SP 16
is designedfor DINwall power outlets.
iJaz can control upto 16 zones and each zone cancontrol an
unlimited number of heaters and/or other appliances
respectively.
A zone can be a heating zone e.g. a living room or a switch
zone like the household coffee maker. Each of the 16 zones
has a unique address, preventing the possibility of a conflict
with another iJaz system. Each zone can have unlimited
numbers ofunits connected.
When installing the system start by planning all zones you
want thecentral unitto control. Installthe heaters and theradio
plugs (RP 200). When installing the heaters use the heater
Installation Instructions. To achieve the best possible
communication it is recommended installing the iJaz central
control unitin thecentre of thehouse orflat.
The wireless connection of the iJaz central control will vary
depending on how many walls and types of walls the signal will
have topenetrate. Thedistance in open airis upto 300 metres
Twoindependent programmes shouldbe prepared.
programme: This programmeis for daily use and should
contain temperature reduction periods for each of the heating
zones. It is possible to programme each day differently with
minimum periods of 15 minutes.All heating zones have a factory
installed defaultweekly programme
from homeprogramme: This programmeis used for longer
periods of absence, typically holidays, business trips etc.
Programme each heating zone tobe as cold as possible to save
maximum energy. Ifyou choose toleave the room temperature at
5 ºC or switch off the heaters completely in some of the rooms
please remember to set your return time to a few hours earlier
than yourreturn. It takes sometime tobring the roomtemperature
back toa normallevel
Normal
Away
.
.
.
The sketch shows iJaz with six heater zones and two switch
zones. The living room is split into two zones; one zone
covering three heaters and the other covering one switch.
When starting iJaz the correct time and date mustbe set. The time and
date canalso beentered in “MenuSettings”.
How to settime and date: use the arrow keysto move left and right.The
cursor will move and indicate the value to set using the + and keys.
When setting is completed pressOK. (The display is pressure sensitive
and worksas akeyboard.)
When pressing i key the user information appears. The i key is
present in almost all the screens giving explanations to the current
picture. Itmakes theiJaz simple touse.
After time anddate is set the system movesdirectly to choosing a zone.
The planned zones must be entered into the programme. The main
screen will showthe zones in the samesequence as they were entered,
first ontop, nextas second etc.
A zonecan control either heatersor wireless switches, notboth. When a
zone isestablished a choice mustbe made to whetherit is aheater zone
or a switch zone. Zones are made under “Menu”and “Zones”. The icon
indicating a heater zone is illustrated as a heater radiating heat waves.
The iconof aswitch zone isillustrated asa wall socket.
A heat zoneindicated by the icon in the upper left corner isestablished.
After the icon is the chosen zone name. The writing keys are similar to
and used in the same way as thekey pad of a mobile phone. Press OK
when the zonename is entered. Manyof the windows havea return key,
bringing youback tothe previous screen.
This is the main screen after zones have been establishedand connected.
The upper grey field contains information about the current programme
mode, timeand dateand the roomtemperature whereiJaz is installed.In this
main screenthe zones fromour example havebeen connected. Morezones
will appearon thescreen when usingthe upand down keys.
Adjusting time and date
Welcome to the iJaz wireless control system.
Installation.
Zone, type and name
Main Screen
Establish and connect zones
After thefirst zonehas been enteredwith a nameit will appearon thescreen.
Additional zones areestablished by pressing “NEW”.Repeat the procedure
until all planned zones are entered. Incorrect entries can be corrected by
using the “Delete/change” key. From the main screen you will find the
procedure for “Establish and Connect Zones” when pressing key “Menu”
and “Zones”.You may atany time add newzones, delete zones andchange
the nameof zones.
The symbol shows thata connectingattempt has notbeen made.
When the “Connect” key is pressed iJaz starts transmitting its unique code
for the chosen zone. The code is transmitted continuously until “OK” is
pressed. Theicon in the upper leftcorner shows it isa heater zone.A heater
or aswitch is connected tothe chosen zoneby pressing the “PAUSE” button
on the RP200 or SP16 for 3 to5 sec. If theconnection is successful theunit
will give a acknowledgement signal by 3 blinks of the green LED. See RP
200 and SP16 User Instructions. Afterconnecting all heaters or switches in
the zone,complete theprocedure by pressing“OK”.
Repeat the procedure for the remaining zones. It is possible at any time to
connect additionalheaters orswitches to aheater orswitch zone bypressing
“Connect” for the wanted zone.Then press “PAUSE” on the RP200, SP 16
respectively.
iJaz is designed for wall installation. Start
with selecting the place of installation. The
recommended height from the floor to the
centre of the display is 160 cm to 180 cm,
depending on howtall the operators are. We
recommend thatyou familiarize yourselfwith
the productbefore it is mountedon thewall. It
will make it easier to choose the best
possible height. Connect the iJaz central
control to the power source. Thenit is easier
to decide which angle gives better visual
display. The display contrast can be
adjusted.
When the location is decided it is time to fix
the wallbracket.
1
2
3
Remove the wall bracket like this: 1. Press the lock. 2. Tilt it
upwards. 3.Slide thebracket off as shown.
The figure shows how to connect the power supply. Only the
power supplydelivered withthe product shouldbe used.
iJaz can be installed onto a wall
junction box to hide the cable if
desired or directly on the wall. A
9V power supply for connection
to 230V single phase supply is
included.
Bedroom 1
Bedroom 2
Living
room
Kitchen
Bath
Hall
Stove with RP200
Sp16, Wireless switch
Symbols explanations
The symbolsappearing inthe zones are:
Indicates that an attempt to connect the zone has not been done.
Indicates the temperature setting of the heater is being maintained.
The communication LED on the RP 200 will show a steady green light.
Indicates lowering the temperature by 5 ºC room temperature from
the set thermostat temperature.
The communication LED on RP 200 will show a blinking green light.
Frost safeguard. Maintaining a minimum of 5 ºC in the room.
The communication LED on RP 200 will show a fast blinking green
light.
Heater off. The heater will not produce any heat.
The communication LED on RP 200 will show an orange light.
This function can be used with the “Away from home” programme only.
Switch is on.
Switch is off.
Shows a zone in PAUSE mode. Heaters connected to this zone will
operate to the temperature set. If the zone is a switch zone the
automatic on/off functions are cancelled and the set PAUSE mode
prevails.
iJaz Central Control
User Instructions
programmable wireless control system for beha panel heaters.
Save energy!
Wireless control system for BEHA panel
heaters.
The iJaz system is simple in design and can
be installed without proffesional assistance.
Control 16 heater or switch zones,
touch screen operated.
Each zone can control an infinite numbers of
heaters or switches.
The iJaz central unit has a built in thermo meter
with output for frost alarm.
Possible to connect a GSM receiver for remote
control.
Available units
Model: SP16
Radio switch for DIN sockets
EL-nr:
5449901 hvit
5449902 sort
Model: RP200
Radio plug for BEHA heaters, white or black.
EL-nr: 5449903
Rev.A
Sett correct date and time!
Date Time
Adjusting time and date
Choosing a zone
Heaters
Switch
Page 2
98 11 13
1410
12
How to activate “Away from home” programme
Press in mainscreen when“Away from home” isgoing to be Press on themain screento enter mainmenu forsettings. Press
activated. You can selectbetween
“Pending further action” or
“Limited period”.
“Pending further action” is
selected when time of return
(coming home) is uncertain. The
“Away from home” programme
will remain activated until normal
mode isagain selected.
If “Limited Period” is selected the
time and date from/to has to be
set. iJaz will thus automatically
select the “Away from home”
programme for the specified
period.
The dateand time from/tois set as
described in section 2. Use the
left/right arrows and the +/- keys.
Press OK when the time frame is
set.
After programming the “Away
from home” setting this is how the
screen may look. The “Suitcase”
icon has been replaced by the
“House” icon, indicating normal
programme mode.
To delete or change the “Away
from home”programme press ,
then press “Activate Normal” or
“Modify awayfrom home”.
The main screen gives you four
possibilities:
“Date/time” is for setting the
correct dateand time.
Press “Zones” for adding or
changing zones,refer tosection 4.
Press “Consume”for checking the
electricity consumptionfor the last
24 hrs, week or month. This will
only be possible if the electricity
metre is connected to the iJaz
system. Please see section 13
about savingelectricity.
Press “System” for adjusting the
screen contrast, carry out a radio
transmitting test or establishing a
pin code for protection of the
settings. When “Radio Test” is
pressed iJaz will transmit a test
signal. All units connected will
pause and the pause LED will
blink.
To establish a PIN-code
protection press the “YES” key.
Then press “SET” key to activate.
At this point you may choose a
PIN-code by entering four digits,
then press “OK”. When the PINcode is activated any change of
settings will haveto be initiated by
the code. When the code has
been entered the system will be
open for changes for as long as
the backlight is on, meaning you
do not have to enter the code for
every change. The backlight will
be on for approximately 3minutes
after the last key operation. Then
the codeis activatedagain.
(As a backup the code 1917 will always
work incase theset code isforgotten.)
On thebackside ofthe iJaz unitthe connectingpoints are:
: Frost detector alarm. This exit connects if
the temperature goes below 5°C. The temperature is
measured byiJaz. This function canbe connected to thehouse
alarm system.
: Not in use, the system is prepared for future
functions notavailable today.
: Connecting terminal 4 to terminal 5 will start
the “Awayfrom home” function.An externalswitch can beused
for this purpose. Theexternal switch can be a GSM controlled
switch whichcan be usedfor starting theheaters from a mobile
phone (SMS).
Terminal 1 and 2
Terminal 3
Terminal 4 and 5
Terminal 6 and 7:
Terminal 7 and 8:
MUST
NOT BE REMOVED
For
connection of the electric metre
(metres with pulse terminal).
iJaz will register total
consumption
The short
circuit between 7 and 8
. The short
circuit is to be removed when
updating the iJaz software only.
This should be done by
authorised personnelonly.A USB
port is available for regular
service functions..
This function will only work with a newer type of electric metre
having pulse connection. Connecting the electric metre to the
iJaz willhave tobe done bya certifiedelectrician only!
When pressing “SET” the
impulse frequency of the
electric metre has to be
entered as well as the excess
consumption limit. iJaz will
show the consumption during
the past 24hrs, the past seven
days andthe pastthree weeks.
Control of excess
consumption can be achieved
by pressing the “kWh” key in
the zone screen. The
possibility to select mode of
the zone when excess
consumption occurs can be
programmed separately for
each zone. It works basically
as the “Away from home”
programme. If the heat zone of
the living room is programmed
to lowerroom temperature 5°C
it will be activated when iJaz
detects excessconsumption.
One or more zones can be set to
pause mode. Pause mode can be
used whenyou are athome or ata
time when youare normally away.
Select the zone youwant to set to
pause mode. The screen will
show the possibilities between
activating the selected zone only
or allzones.
If you want all zones in pause
mode press “All zones” and then
“Activate”.
The “Pause” symbol ll will
appear in front of the zones in the
main screen.
In orderto turn offthe pause mode
press “Pause” button, then press
“Selected zone” or “All zones”
(depending on the previous
choice) andthen “Deactivate”.
The pause mode does not have any automatic delete function. If
“Pause” isactivated it will bein pause modeuntil it is deactivated.
If, on the other hand, the pause mode on external units (RP 200
and SP 16) that are connected have an automatic deactivating
function when they are in use. You will find more information on
RP 200 andSP 16pause functions in theiruser manuals.
Programming of zones - Heater Zone
Pause function
Touch onthe mainscreen while thezone youwant to
Press on themain screenfor activating pause.
programme is marked. The first
screen appearing shows the
setting for one week. Our
example showsa heatingzone.
How to change the setting on
Saturday and Sunday: Touch
Saturday and Sunday. A frame
will showthe days chosen.Press
“Change Day”.
The chosen days will appear.
The top of the graph bar shows
the time is 00 hrs, the bottom is
24 hrs. Use the up and down
keys to move vertically on the
bar. One of three function
settings is possible: Set Room
Temperature, Lower 5 ºC or
Frost Safeguard(snow crystal).
If none of the three possibilities
have been selected nothing will
change when you move the
cursor up or down the graph bar.
If one of the keys is pressed the
selected function will be entered
into theprogramme next timethe
up or down arrow keys are
pressed. A bold frame around
the function key shows which
key isselected.
When pressing thesuitcase icon
“Away from home” (first screen
of the zoneprogramme) you can
select the setting of the absent
zone: Since this is a heater zone
the selections available are: normal programme, lower 5 ºC,
frost guard or switch off. If
“Normal” is selected it means
that the normal programme will
be in use when “Away from
home” modeis activated.
“kWh” key, please see explanationin section13
Menu settings Saving energy at excess consumption
An on/off switch zone is
programmed the same way as
a heater zone, refer to
introduction in section 8. When
“Suitcase/Pause” button is
pressed the switch zone mode
can be selected if the zone is
activated by the “Away from
home” or“Pause” programme.
Programming of zones - Switch Zone
And
Connections
NB!
At room temperature below 10 ºC the LCD screen will appear
darker and the reaction time will be slower.
If a heater zone is programmed to be switched off with the
setting “Switch zone off” the zone will not be protected by
“Frost Safeguard”.
Rev.01
Loading...