Beglec STAGE BEAMER RGB V1.0 User Manual
T
ABLE OF CONTENTS
PART 1 PRODUCT (GENERAL)....................................................1.
1.1--PRODUCT INTRODUCTION.........................................................1.
1.2--PRODUCT FEATURES.................................................................1.
1.3--TECHNICAL SPECIFICATIONS.....................................................2.
1.4--PHOTOMETRIC DATA..................................................................3.
1.5--SAFETY WARNING......................................................................4.
PART 2 INSTALLATION...............................................................5.
2.1--MOUNTING...................................................................................5.
2.2--POWER CONNECTION..................................................................5.
2.3--SETTING UP WITH A DMX512 CONTROLLER.................................6.
2.3-1--DMX512 ADDRESSING WITHOUT ID ADDRESSING......................................6.
2.3-2--DMX512 ADDRESSING WITH ID ADDRESS..................................................6.
PART 3 DISPLAY PANEL OPERATION.........................................8.
3.1--BASIC..........................................................................................8.
3.2--MENU..........................................................................................9.
3.3--EDIT STATIC COLOUR............................................................... 10.
3.4--ACTIVATING AUTO PROGRAMS.................................................10.
3.5--RUN MODE................................................................................ 10.
3.6--DMX512 SETTINGS....................................................................11.
3.7--PERSONALITY...........................................................................11.
3.8--ID ADDRESS..............................................................................11.
3.9--EDITING CUSTOM PROGRAMS ................................................ 12.
3.10--SPECIAL SETTINGS.................................................................12.
3.11--WHITES SETTING ....................................................................13.
3.12--WHITES BALANCE .................................................................. 13.
3.13--A CTIVATE THE PASSWORD .................................................... 13.
PART 4 USING A DMX512 CONTROLLER....................................14.
4.1--BASIC ADDRESSING.................................................................14.
4.2--CHANNEL ASSIGNMENT............................................................14.
4.3--BASIC INSTRUCTIONS FOR DMX512 OPERATION......................18.
PART 5 APPENDIX......................................................................19.
5.1--TROUBLE SHOOTING...............................................................19.
5.2--MAINTENANCE......................................................................... 20.
1 PRODUCT (GENERAL)
1.1 PRODUCT INTRODUCTION
This product is designed for indoor use. Suitable applications include wash or effect lighting for
architectural, stage, theatre or road show applications. Direct input of DMX512 signal allows the
units to be controlled from any DMX512 controller. This product can be operated as a single unit or in
multiple units for large applications.
1.2 PRODUCT FEATURES
LED FIXTURE
* RGB Dimmer 0-100%
* Strobe
* Built-in automatic programs
* Upload custom parameters to slave fixtures
* LED display
* Display control 'lock-out'
* Direct DMX512 input
* Independent ID address
* Different white colors setting
* 'Over-heat' protection
1 PRODUCT(GENERAL)
1
2009.11.10
1.3 TECHNICAL SPECIFICATIONS
LED MODULE
LED MODULE:
Voltage
Rated Power
LED/Unit
Environment Temperature
Cooling
Dimensions
Weight
100~250V...50/60Hz
52W
14 X 3W Tri-RGB
-20 ~40
Direct air convection
245 x 205 x 245mm
4.8Kg
1 PRODUCT(GENERAL)
2
2009.11.10
1.4 PHOTOMETRIC DATA
1 PRODUCT(GENERAL)
3
2009.11.10
1.5 SAFETY WARNING
IMPORTANT
ALWAYS READ THE USER MANUAL BEFORE OPERATION.
PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE
PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR
AREA.
This product must be installed by a qualified professional.
Always operate the equipment as described in the user manual.
A minimum distance of 0.5m must be maintained between the equipment and
combustible surface.
The product must always be placed in a well ventilated area.
Always make sure that the equipment is installed securely.
DO NOT stand close to the equipment and stare directly into the LED light
source.
Always disconnect the power supply before attempting and maintenance.
Always make sure that the supporting structure is solid and can support the
combined weight of the products.
The earth wire must always be connected to the ground.
Do not touch the power cables if your hands are wet.
ATTENTION
This product left the place of manufacture in perfect condition. In order to
maintain this condition and for safe operation, the user must always follow the
instructions and safety warnings described in this user manual.
Avoid shaking or strong impacts to any part of the equipment.
Make sure that all parts of the equipment are kept clean and free of dust.
Always make sure that the power connections are connected correct and
secure.
If there is any malfunction of the equipment, contact your distributor
immediately.
When transferring the product, it is advisable to use the original packaging in
which the product left the factory.
Shields, lenses or ultraviolet screens shall be changed if they have become
damaged to such an extent that their effectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally
deformed.
1 PRODUCT(GENERAL)
4
2009.11.10
2 INSTALLATION
2.1 MOUNTING
HANGING
The fixture can be mounted in a hanging
position using the supporting bracket. The
bracket should be secured to the mounting
truss or structure using a standard
mounting clamp. Please note that when
hanging the unit a safety cable should also
be used.
UPRIGHT
The fixture can be mounted in an upright or
sitting position using the supporting
brackets.
The LED MODULE can be mounted at any angle and in any
position. It is possible to further adjust the angle of the LED
MODULE using the two adjustment knobs located on the side of
the fixture.
2.2 POWER CONNECTIONS
@ 220V: 24 units may be connected in series
@120V: 12 units may be connected in series
Note:
If the signal cable is over 60m between the DMX512 controller and fixture or
beween two fixtures, then a DMX signal amplifier is needed as well.
2 INSTALLATION
5
2009.11.10
Loading...