Beglec BTX 300 BEAM V1.0 User Manual

DANGER ~ GEVAAR ~ GEFAHR ~ PELIGRO ~ PERIGO

!

WARNING: DANGER! never expose the lens to direct sunlight, even for a short period. This may damage

the light effect or even cause fire!

ATTENTION: DANGER! n'exposez jamais la lentille directement aux rayons de soleil, même pendant un

bref instant. Ceci peut endommager l'intérieur de l'appareil ou même causer un incendie !

OPGELET : GEVAAR ! stel de lens nooit bloot aan direct zonlicht, zelfs gedurende een korte periode. Dit

kan het toestel beschadigen en zelfs brand veroorzaken!

WARNUNG: GEFAHR! Setzen sie die Linse niemals direkter Sonneneinstrahlung aus, auch nicht für eine

kurze Zeit ! Die direkte Sonneneinstrahlung kann das Gerät zerstören oder zum brennen bringen!

ADVERTENCIA: ¡PELIGRO! ¡nunca exponga la lente a la luz solar directa, aún durante un período corto!

¡Esto puede dañar el efecto de luz o incluso causar el fuego!

AVISO: PERIGO! Nunca exponha as lentes directamente à luz solar, mesmo que por pouco tempo! Isto

pode danificar o efeito luminoso ou mesmo provocar um incêndio!

EN - DISPOSAL OF THE DEVICE

Dispose of the unit and used batteries in an environment friendly manner according to your country regulations.

FR - DÉCLASSER L’APPAREIL

Débarrassez-vous de l’appareil et des piles usagées de manière écologique, conformément aux dispositions
légales de votre pays.

NL - VERWIJDEREN VAN HET APPARAAT

Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke manier conform de in uw land geldende
voorschriften.

DU - ENTSORGUNG DES GERÄTS

Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und Weise gemäß den Vorschriften Ihres Landes.

ES - DESHACERSE DEL APARATO

Reciclar el aparato y pilas usadas de forma ecologica conforme a las disposiciones legales de su pais.

PT - COMO DESFAZER-SE DA UNIDADE

Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em conformidade com as normas vigentes no seu país.

1. Safety Instruction

Due to the magnifying type lens, please keep the lens out of contact

of the unit, which will seriously damage

the

unit.

Please read carefully the instruction manual, which includes important

WARNING

Please
keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction manual.

Important:
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.

 Unpack and check carefully that there is no transportation damage before using the

unit.

 The unit is for indoor use only. Use only in a dry location.
 Do install and operate by qualified operator.
 Do not allow children to operate the fixture.
 Use safety chain when fixing the unit. Handle the unit by carrying its base instead of

head only.

 The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces.

 Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
 Before operating, ensure that the voltage and frequency of power supply matches the

power requirements of the unit.

 It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

 Maximum ambient temperature TA: 40°. Don’t operate it when the temperature is

higher.

 Don’t connect the device to any dimmer pack.
 During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, and it will decrease gradually
within 15 minutes.

 Make sure there are no flammable materials close to the unit while operating to avoid

fire hazard.

 Examine the power wires carefully; replace them immediately if there is any damage.
 Unit’s surface temperature may reach up to 85°. Don’t touch the housing bare-handed

during its operation, and allow about 15 minutes for cooling the unit down before
replacing bulb or maintenance as it could be very hot.

 Avoid any inflammable liquids, water or metal objects entering the unit. Once it

happens, cut off the mains power immediately.

 Do not operate in dirty or dusty environment; do clean the fixture regularly.
 Do not touch any wire during operation as there might be a hazard of electric shock.
 Avoid power wires twist other cables.
 The minimum distance between light output and the illuminated surface must be more

than 2.5 meters.

 Disconnect mains power before fuse/lamp replacement or servicing.
 Replace fuse/lamp only with the same type.
 In the event of serious operating problem, stop using the unit immediately.
 Never turn on and off the unit time after time.
 The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

information about the installation, usage and maintenance.

 Do not open the unit as there are no user serviceable parts inside.
 Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead

to damage or malfunction. Please contact the nearest authorized technical assistance
center if needed.

 Disconnect the mains power if the fixture is has not been used for a long time.
 Do use the original packing materials before transporting it once again.

Caution

with direct sunlight. Direct sunlight can cause heat to build up inside

 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

 Hot lamp explosion hazard. Do not open the unit within 15 minutes after switching off.
 Do replace the bulb once it is damaged, deformed or life-expired.
 Do not look directly at the light while the bulb is on.
 Never touch bulb with bare fingers, as it is very hot after using.
 Do not start on the unit without bulb enclosure or when housing is damaged.

Product Items

 User manual
 2 x Omega clamps

2. Installation

Unpacking the fixture (for flight case pack only)

1.Stop the flight case via the brake sheet above the wheels.

2.Unlock the lock modules (1) and open the cover board.

3.Prop the cover board with lid bracket.

4.Take out the fixture.

5.Unlock the lock module (2) take out omega clamps.

Installation:

1. Bolt each clamp (1) to the Omega holder with screw and
lock nut through the hole in the holder.

2. Fasten the omega holders (2) on the bottom of the base
by inserting quick-lock fasteners (3) into the holes of the
base and tighten fully clockwise.

3. Hang the fixture to the support (4) through clamp and fasten the screws (5). Fasten the
safety cable (6) through the bottom of the base and over the support.

Fig.1 Fig.2

BRITEQ® 1 BTX-300BEAM

BRITEQ® 2 BTX-300BEAM

Attention:

 Always ensure that the structure to which you are attaching the unit is secure and is

able to support a weight of 10 times of the unit’s weight without any harming
deformation.

 Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

 Make absolute sure that the unit is firmly fixed in way that no vibrating or slipping would

occur during operation.

 The equipment must be installed beyond the areas where persons may walk by or be

seated.

 The rigging has to be operated by or under the guide of a skilled person.

3. Technical Specification

Power supply

- AC 100~240V 50/60Hz

Power Consumption

- 416W (230V)

- 434W (120V)

Fuse

- T 10 A

Lamp

- Philips MSD Gold 300/2 miniFastFit ICT

Battery backup display

- Setting DMX address or other functions without connecting to mains power.

- Battery for LCD display charges automatically when the fixtures connects to the mains
power.

- No need to change battery.

Wireless control (for the unit with wireless receiver built-in only)

- Wirelessly controlled by W-DMX (option).

- Each W-DMX is sending out 512 channels of DMX.

- License free band of 2.45 GHz

Optical system

- High efficiency optical system, delivering extremely powerful output

- High quality dichroic lenses

- Beam angle: 8°

Movement

- Pan: 540°

- Tilt: 270°

- Pan/Tilt moving speed adjustable.

- Automatic Pan/Tilt correction.

- Easy calibration and maintenance by magnetic home positioning.

- Pan/Tilt position lock for transporting protection.

Dimmer/Shutter

- Blackout, 0~100% smooth dimming, independent shutter and various strobe effect.

Color wheel

- Color wheel: 7 dichroic colors + open.

- Rainbow effect in both directions.

- Easy calibration and maintenance by magnetic home positioning.

CMY

- CMY speed adjustable.

- Optional multiple preset colors and macros available.

Gobo wheel

- Gobo size: Ø26.8mm (Ø24mm for image)

- Gobo Wheel: 7 rotating, indexable, easily replaceable gobos + open.

- Easy calibration and maintenance by magnetic home positioning.

- Module design for easy assembly and service.

Prism

- 3 facets prism with rotating effect.

Frost

- Frost effect.

Cool

- Fan cooled

Protocols

- DMX 512

- Date input/output: 3/5 Pin XLR

socket

Dimension

- 447 × 369 × 604 mm

Weight

- 21kgs

Photometric diagram

BRITEQ® 3 BTX-300BEAM

BRITEQ® 4 BTX-300BEAM

DMX Channels

Mode

CH

1 Pan Shutter Pan
2 Pan Fine Dimmer Pan Fine
3 Tilt Cyan Tilt
4 Tilt Fine Magenta Tilt Fine
5 Pan /Tilt Speed Yellow Pan /Tilt Speed
6 Shutter Color Dimmer
7 Dimmer Gobo Dimmer Fine
8 Color R-Gobo Shutter

9 Cyan R-Gobo Fine Color
10 Magenta Prism Cyan
11 Yellow R-Prism Magenta
12 Preset Color Pan Yellow
13 Gobo Pan Fine CMY Speed
14 R-Gobo Tilt Gobo
15 Prism Tilt Fine R-Gobo
16 R-Prism Pan /Tilt Speed R-Gobo Fine
17 Frost Frost Prism
18 Function Function R-Prism
19 R-Prism Fine
20 Frost
21 P/T Macro
22 P/T Macro Speed
23 Preset Color
24 Color Macro
25 Function

Mode 1

18-CH

Mode 2

18-CH

Mode 3

25-CH

The head can be locked for transportation protection-the tilt lock button (4) is pressed and
the pan lock/unlock lever (6) is in lock position. To unlock the head, press the tilt unlock
button (5) and move the pan lock/unlock lever (6) to unlock position.

Caution: The head and arm must be unlocked before operation!

4.2 Control Panel

Front view Rear view

,1 Monitor (Batter Back-up display):

○

,2 LED

○

POWER On Power on
DMX On DMX input present

,3 Button

○

MENU

UP To go backward to move up in the menu
DOWN To go to move down in the menu

ENTER To perform the desired functions

To enter into, move backward or leave the menu

4. Description

4.1 Description of the fixture

1.Arm

2.Front panel

3.head

4.Tilt lock button (Black)

5.Tilt unlock button (Gray)

6.Pan lock

7.Handle

8.Base

9.Antenna (for XP-300A BEAM WT only)

BRITEQ® 5 BTX-300BEAM

,4 Antenna (optional)

○

Receive wireless signal from a wide range

,5 DMX input/output:

○

For DMX 512 operation, use 3/5-pin XLR plug cable to link the units together

,6 Power Switch:

○

Turns On/Off the power

,7 Power Cable:

○

To connect to the mains supply

,8 Fuse (T 10 A):

○

Protect the unit from damage of overcurrent.

BRITEQ® 6 BTX-300BEAM