Beglec BT-20LS V1.0 User Manual

75
USER
MANUAL
Ver 1,0
T
ABLE OF CONTENTS
PART 1 PRODUCT (GENERAL)................................................................. 1.
1.1--PRODUCT INTRODUCTION........................................................................1.
1.2--PRODUCT OVERVIEW................................................................................1.
1.3--TECHNICAL SPECIFICATIONS................................................................... 2.
1.4--PHOTOMETRIC DATA.................................................................................3.
1.5--SAFETY WARNING.....................................................................................3.
PART 2 INSTALLATION ........................................................................... 4.
2.1--MOUNTING................................................................................................4.
2.2-- ............................................................................... 5.
2.3--SETTING UP (STAND ALONE).................................................................... 5.
2.4--LED PCB .......................................................................... 6.
2.5--GOBO ............................................................................... 6.
2.6--SETTING UP (MASTER/SLAVE).................................................................. 7.
2.7--SETTING UP (DMX512 CONTROLLER)....................................................... 7.
PART 3 DISPLAY PANEL OPERATION....................................................... 8.
3.1--BASIC........................................................................................................8.
3.2--MENU........................................................................................................ 8.
3.3-- .......................................................................................................10.
3.4-- ......................................................................................................10.
3.5-- ......................................................................................................11.
3.6-- ................................................................................................... 11.
3.7-- ..........................................................................................................12.
3.8-- .................................................................................................. 12.
FUSE REPLACEMENT
REPLACEMENT
REPLACEMENT
INTRO INVERT RANGE SPECIAL EDIT DEFAULT
PART 4 USING A DMX512 CONTROLLER...................................................13.
4.1--BASIC ADDRESSING................................................................................. 13.
4.2--CHANNEL ASSIGNMENT............................................................................ 13.
PART 5 APPENDIX................................................................................... 16.
5.1--TROUBLE SHOOTING................................................................................ 16.
5.2--MAINTENANCE.......................................................................................... 17.
1 PRODUCT (GENERAL)
1.1 PRODUCT INTRODUCTION
This product is designed for indoor use only. Suitable for stage, bar or nightclub applications. Direct input of DMX512 signal allows the fixtures to be controlled from any DMX512 controller. The fixture is fully programmable with one custom program available and is supplied with two automatic programs (all accessible from DMX512 controller). This product can be operated as a single unit or with multiple units for large applications.
1.2 PRODUCT OVERVIEW
ITEM
No
1
Head
2
Arm Base
3
Menu
4
Enter
5
Down
6
Up
7
Switch
8
Fuse
9
10
Power input
11
DMX 3-PIN signal output DMX 3-PIN signal input
12
1 PRODUCT(GENERAL)
1
2009.2.8
1.3 TECHNICAL SPECIFICATIONS
Electrical
Voltage:AC100~240V 50/60Hz Rated Power:75W
LED
LED:1PC(20W white) Cooling:Forced air convection
Optical System
Focus:Manual linear focus Dimmer:0~100% Strobe:0~20Hz 3-facet Prism
Operation
Control mode: DMX512/Master-Slave/Auto/Custom/ Sound LCD display DMX512 Chs: 9 CHS/12CHS
Pan/Tilt
Pan 540 Tilt 270 Pan/Tilt speed User-selectable Pan/Tilt ranges Reverse Pan/Tilt movement
Rotating Gobo
7 Gobo (interchangeable) Gobo-flow effect Gobo shake Bi-directional rotation
Color
9 dichroic - filters Rainbow - flow effect
Other features
Custom program (255 steps) Size: 240x200x3540mm
Weight: 7kg
1 PRODUCT(GENERAL)
2
2009.2.8
1.4 PHOTOMETRIC DATA
2000
0
2(0.5)
588 256 147 97 LUX
4(1.1)
6(1.7) 8(2.2)
1.5 SAFETY WARNING
IMPORT ANT
ALWAYS READ THE USER MANUAL BEFORE OPERATION. PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE
PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA.
This product must be installed by a qualified professional. Always operate the equipment as described in the user manual.
A minimum distance of 0.5m must be maintained between the equipment and
combustible surface.
The product must always be placed in a well ventilated area. Always make sure that the equipment is installed securely.
DO NOT stand close to the equipment and stare directly into the LED light
source.
Always disconnect the power supply before attempting and maintenance.
Always make sure that the supporting structure is solid and can support the
combined weight of the products.
The earth wire must always be connected to the ground. Do not touch the power cables if your hands are wet.
16
10Distance(m)
2.8 Diameter(m))
ATTENTION
1 PRODUCT(GENERAL)
This product left the place of manufacture in perfect condition. In order to
maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual.
Avoid shaking or strong impacts to any part of the equipment. Make sure that all parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and
secure.
If there is any malfunction of the equipment, contact your distributor
immediately.
When transferring the product, it is advisable to use the original packaging in
which the product left the factory.
Shields, lenses or ultraviolet screens shall be changed if they have become
damaged to such an extent that their effectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally
deformed.
3
2009.2.8
2 INSTALLATION
2.1 MOUNTING
The LED fixture can be operated in any position at any angle. When mounted on a flat surface, the surface must be strong enough to support 10 times the weight of the fixture and stable so that there will be no damage caused to the fixture or surrounding people or objects because of movements of the fixture on the surface.
When the unit is mounted in a hanging position, the fixture is attached using the mounting brackets and a standard truss clamp or other clamping device. The mounting brackets supplied are mounted using quick-release locks allowing simple mounting or removal.
Bracket
Clamp
Safety cable
UPRIGHT
HANGING
IMPORTANT SAFETY NOTE!!
Always use a safety cable when installing this unit!! Be sure that the safety cable is connected to a solid load-bearing structure.
2 INSTALLATION
4
2009.2.8
2.2 FUSE REPLACEMENT
Remove the safety cap by a screwdriver.
F
etch the old fuse from safety cap.
I
nstall a new fuse.
I
nstall the safety cap.
Fuse
Safety Cap
2.3 SETTING UP (STAND ALONE)
The LED fixture can be used as a stand alone unit. The stand alone functions AUTO 1, AUTO 2, SOUND 1, SOUND2 and CUSTOM can be activated without the need to connect to any controller or connecting to any other equipment. Simply, access the <operation> menu from the DISPLAY and select the target program to activate.
2 INSTALLATION
5
2009.2.8
2.4 LED PCB REPLACEMENT
Take off the head cover. Remove the fan cover, fan, fan supports, heat sink step by step.
Replace the new LED PCB. I nstall all parts on the original position.
Head cover
Fan cover
Fan supports
23 lenses
Fan
Heat sink
LED PCB
2.5 GOBO REPLACEMENT
Unlock the sliding the knob on the gobo slot door
Pull up the gobo slot door and turn it to a proper position.
Take out the bad gobo. Install the good gobo, lock the gobo slot door.
Gobo slot door
Sliding knob
2 INSTALLATION
6
.
Gobo
2009.2.8
2.6 SETTING UP (MASTER/SLAVE)
When units are connected in series using DMX512 signal cable connect the units as shown in the diagram below Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first (MASTER) fixture. Connect the end of the cable coming from the MASTER fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then proceed to connect from the output as stated above to the input of the following fixture and so on.
Set the first unit in the series to one of the STAND ALONE modes as described in section
2.2 All other units in the series should be set to <SLAVE> from the <operation> menu.
MASTER SLAVE SLAVE
2.7 SETTING UP (DMX512 CONTROLLER)
When units are connected in series to a DMX512 controller and other DMX512 equipment, connect the equipment as shown in the diagram below. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the controller. Connect the end of the cable coming from the controller which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then proceed to connect from the output as stated above to the input of the following fixture and so on. If over 32pcs fixtures connected ,the amplifier is needed.
DMX512 CONTROLLER
2 INSTALLATION
7
2009.2.8
3 DISPLAY PANEL OPERATION
3.1 BASIC
The LED fixture is mounted with a LCD display and 4 control buttons.
MENU Scroll through the main menu or exit from the current sub-menu ENTER Enter the currently selected menu or confirm the current function value
DOWN Scroll 'DOWN' through the menu list or decrease the value of the current function UP Scroll 'UP' through the menu list or increase the value of the current function
3.2 MENU
MENU
Intro
ENTER
DOWN
Address
Reset
Run
Channels
Display
Info
UPMENU
(001~512)
Yes No
DMX512 Auto 1 Auto 2 Sound 1 Sound 2 Custom Test Slave
Basic Advanced
60 close
Bright
Edition
3 DISPLAY PANEL OPERATION
Invert
Pan
Tilt
Color
Use
8
Normal Reverse
Normal Reverse
Step Linear
No Yes
2009.2.8
Range
P/start P/Finish T/start T/Finish Use
(000~255) (000~255) (000~255) (000~255) No
Yes
Special
Edit
Default
Black
Reset
Step Pan
Tilt Speed Color Gobo Gobo.rot Prism Dimmer Strobe Time Use
Default
No
Yes
Dmx
System
(000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255)
No Yes
No Yes
3 DISPLAY PANEL OPERATION
9
2009.2.8
3.3 INTRO
MENU
Intro
Address
Reset
Run
Channels
Display
Info
(001~512)
Yes No
DMX512 Auto 1 Auto 2 Sound 1 Sound 2 Custom Test Slave
Basic Advanced
60 close
Bright
Edition
Address
Enter Address to set the DMX Address, which is from (001-512)
Reset
In order to rest custom modest to default, select
Reset
Run
Enter to select the operation mode: ; ;
Run DMAX512 Auto1
; Sound 1 ; Sound 2 ;;;
Auto2 Custom Test Slave
Channels
Enter to select the DMX channel modes: ;
Channels Basic Advanced .
Display
Enter to select the lighting time of the LCD display panel.
Display
Info
Enter to see the version of the software.
Info
3.4 INVERT
MENU
Invert
Normal Reverse
Select Pan / Tilt to set or Select Color to select the color wheel flow way Step or linear
Use Yes
Enter and set to run the new setting
Invert
Pan Normal
Reverse
Tilt
Color
Use
Normal Reverse
Step Linear
No Yes
3 DISPLAY PANEL OPERATION
10
2009.2.8
3.5 RANGE
MENU
P/start
Set pan start value 000~255
P/Finish
Set pan finish value 000~255
T/start
Set Tilt start value 000~255
T/Finish
Set Tilt finish value 000~255
Use
Use Yes
Enter and select to open the operation of X/Y angle
3.6 SPECIAL
Range
P/start P/Finish T/start T/Finish Use
(000~255) (000~255) (000~255) (000~255) No
Yes
MENU
Special
Black
Reset
No
Yes
Dmx
System
Black
Enter Black to choose No without delay or Yes 3seconds
delay
Reset
Enter Reset to choose DMX DMX control reset or System DMX
cannot control reset
3 DISPLAY PANEL OPERATION
11
2009.2.8
3.7 EDIT
MENU
Edit
Step Pan
Tilt Speed Color Gobo Gobo.rot Prism Dimmer Strobe Time Use
(000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255) (000~255)
No Yes
Edit
Enter the Edit mode to edit the custom programs by adjusting the
value of Step , Pan , Tilt , Speed , Color , Gobo ,
Gobo.rot , Prism , Dimmer , Strobe , Time
Enter and select to run the steps user need.
Use Yes
Note: if user want to circulate the created steps, please set the last step s T as 0
ime
For example, there are 3 steps, the setting should be like belowed: Step 1 T = 4 = Yes Step 2 T = 5 = Yes Step 3 T = 0 = Yes
ime Use ime Use ime Use
3.8 DEF AULT
MENU
Default
This functions will reset all setting to the original factory setting
Default
Default
No Yes
3 DISPLAY PANEL OPERATION
12
2009.2.8
4 USING A DMX512 CONTROLLER
4.1 BASIC ADDRESSING
Connect all of the units in series using standard DMX512 signal cable . Set the DMX512 address in the DMX menu. It is possible to have the same DMX address or independent addresses for each fixture.
4.2 CHANNEL ASSIGNMENT
Note: This product have two DMX512 channel configuration: ADVANCED and BASIC .
ADVANCED
CHANNEL VALUE FUNCTION
1
2
3
4
5
6
7
0 255
0 255
0 255
0 255
0 255
0 14 15 29 30 44 45 59 60 74 75 89 90 104
105 119 120 134 135 149 150 255
0 9 10 19 20 29 30 39 40 49 50 59 60 69 70 79 80 99
100 119 120 139 140 159 160 179 180 199 200 219 220 255
PAN
0~ 054
PAN FINE
Fine control of pan movement
TILT
0~270
TILT FINE
Fine control of tilt movement
PAN/TILT SPEED
From fast to slow
COLOR WHEEL
White Red Yellow Green Pink Blue Orange
Magenta light blue light green Rainbow & linear effect
GOBO WHEEL 1 & GOBO SHAKE
NO Gobo Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Shaking gobo 7 Shaking gobo 6 Shaking gobo 5 Shaking gobo 4 Shaking gobo 3 Shaking gobo 2 Shaking gobo 1 Flow effect
4 USING A DMX512 CONTROLLER
13
2009.2.8
CHANNEL VALUE FUNCTION
GOBO ROTATION
8
9
10
11
12
0 2
3 6
7 128
129 132 133 136 137 255
0 127
128 255
0 255
0 31 32 63 64 95 96 127
128 159 160 191 192 223 224 255
0 19 20 39 40 59 60 79 80 99
100 119 120 139 140 159 160 179 180 199 200 219 220 255
Stop Slowest
Rotate from slow to fast Stop
Reverse rotate slowest
Reverse rotate from slow to fast
PRISM
NO FUNCTION
In 3-facet prism
DIMMER
Dark
STROBE
Close Open Strobe: Slow > Fast Open Rulse strobe effect: Slow > Fast Open Random strobe effect: Slow > Fast Open
CONTROL
No function Pan/tilt black activated (activated after 3 secs) Pan/tilt black deactivated (activated after 3 secs) Auto1 (activated after 3 secs) Auto2 (activated after 3 secs) Sound 1(activated after 3 secs) Sound 2(activated after 3 secs) Custom Test (activated after 3 secs) No function Reset (activated after 3 secs) No function
Bright
BASIC
CHANNEL VALUE FUNCTION
4 USING A DMX512 CONTROLLER
1
2
3
0 255
0 255
0 14 15 29 30 44 45 59 60 74 75 89 90 104
105 119 120 134 135 149 150 255
PAN
0~ 054
TILT
0~270
COLOR WHEEL
White Red Yellow Green Pink Blue Orange
Magenta light blue light green Rainbow & linear effect
14
2009.2.8
BASIC
CHANNEL VALUE FUNCTION
GOBO WHEEL 1 & GOBO SHAKE
0 9 10 19 20 29 30 39
4
5
6
7
8
9
40 49 50 59 60 69 70 79 80 99
100 119 120 139 140 159 160 179 180 199 200 219 220 255
0 2
3 6
7 128
129 132 133 136 137 255
0 127
128 255
0 255
0 31 32 63 64 95 96 127
128 159 160 191 192 223 224 255
0 19 20 39 40 59 60 79 80 99
100 119 120 139 140 159 160 179 180 199 200 219 220 255
NO Gobo Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Shaking gobo 7 Shaking gobo 6 Shaking gobo 5 Shaking gobo 4 Shaking gobo 3 Shaking gobo 2 Shaking gobo 1 Flow effect
GOBO ROTATION
Stop Slowest
Rotate from slow to fast Stop
Reverse rotate slowest
Reverse rotate from slow to fast
PRISM
NO FUNCTION
In 3-facet prism
DIMMER
Dark
STROBE
Close Open Strobe: Slow > Fast Open Rulse strobe effect: Slow > Fast Open Random strobe effect: Slow > Fast Open
CONTROL
No function Pan/tilt black activated (activated after 3 secs) Pan/tilt black deactivated (activated after 3 secs) Auto1 (activated after 3 secs) Auto2 (activated after 3 secs) Sound 1(activated after 3 secs) Sound 2(activated after 3 secs) Custom Test (activated after 3 secs) No function Reset (activated after 3 secs) No function
Bright
4 USING A DMX512 CONTROLLER
15
2009.2.8
5 APPENDIX
5.1 TROUBLE SHOOTING
SITUATION
No power
LED not lit
Fan do not work
Fixture reset normal, But not be controlled
Prism error
Color wheel error
Rotating gobo wheel error
Pan movement error
Tilt movement error
CAUSE
Power connection error Fuse damaged Power supply damaged Power switch damaged
LED driver PCB damaged LED PCB damaged
LED PCB connection error
Head fan error
Base fan error
Display PCB damaged DMX PCB damaged or DMX signal
connection error
Motor damaged Prism belt broken
Motor damaged
Sensor PCB damaged
Motor damaged Rotating Gobo wheel blocked Sensor PCB damaged
Motor damaged Pan belt broken
Magnetic sensor PCB damaged Optical sensor damaged
Motor damaged
LED607 CONTROL PCB ERROR
Tilt belt broken Magnetic sensor PCB damaged Optical sensor damaged
ACTION
Check all Power connectons Replace Fuse Replace Power supply Replace Power switch Replace LED driver PCB Replace LED PCB
Check the connections
Fan # (60x60x20)
Check the LED driver PCB
Fan #(40x40x10)
Check the power supply Replaced Display PCB
Check DMX signal connection or replace DMX PCB
Replace motor Replace belt Replace motor Replace sensor Replace motor Check or replace the gobo wheel Replace the sensor Replace Pan motor Replace pan belt Replace the magnetic sensor Replace the optical sensor Replace Tilt motor Replace tilt belt Replace the magnetic sensor Replace the optical sensor
5 APPENDIX
16
2009.2.8
5.2 MAINTENANCE
5 APPENDIX
No
1
Front lense cover
2
Front 42 lense
3
Mouth cover
4
Prism
5
32 lense
6
Color wheel
7
Rotating Gobo wheel
8
23 lense
9
LED PCB Head cover B
10
Gobo slot door
11
Sliding knob
12
ITEM
17
No
13
Head fan cover
14
Control PCB
15
Head cover A
16
Driver PCB
17
Arm
18
Base cover
19
DMX socket (Female)
20
DMX socket (Male)
21
Power on/off
22
Power socket
23
Power supply Display PCB
24
ITEM
Version 1.0
2009.2.8
Loading...