B.E.G. LUXOMAT PD4-M-DALI, LUXOMAT PD4-M-DSI, LUXOMAT PD4-M-PD4-S Operating Instruction

EN

!

!

!

!

!

!

TIME

TE

1

3

6

22

18

16

10

30

25

LED OFF

TIME

TE

1

3

6

22

18

16

10

30

25

LUX

40

2000

600

1200

200

TIME

TE

1

3

6

22

18

16

10

30

25

LUX

40

2000

600

1200

200

20%

60

5

10

50

30

OFF

ON

Master Slave

L

N

E1 DALI/DSI

L

N
DA
DA

LN RS + -

DALI

NLR

T1

Master Slave

T1

!

LED
OFF

DSI

DALI

VA

HA

LED
ON

DALI_DSI

LED ON_

LED OFF VA_HA

LUXOMAT

Installation and Operating Instruction for B.E.G. - Occupancy detector

1. Product information

• Occupancy sensor for daylight-dependent lighting control

• DALI / DSI interface for controlling digitally dimmable
electronic ballasts as a group

• Switching between DSI and DALI program by remote
control or DIP switches

• Version as Master

• Extension of the coverage area by slave devices are
possible

• Other functions can be adjustable by remote control.

• Manual switching and dimming via pushbutton
possible

• Orientation light function

2. Operation

The presence detector controls the light automatically according
to people present (movements) and the ambient brightness.

The integrated light sensor constantly measures the ambient light
and compares it with the brightness level on the detector. If the
ambient light is sufficient, lighting will not be switched..
If the ambient light level is below the brightness level, a move­ment activated the lighting in the room.

The detector switch the light off instead of a person, if there is
enough natural light for 5 min. or until the follow-up time do not
recognized any movement in the room.

3. Safety information

Work on the 230V mains supply may only be
carried out by qualified professionals or by

instructed persons under the direction and super­vision of qualified skilled electrical personnel in
accordance with electrotechnical regulations.

Disconnect supply before installing!

This device is not suitable for disconnection.

Mounting the cover ring, after introduction of the
power cable (FC version)

4a.

Mounting SM

close

open

The detector must be mounted on a flatsolid ground. Before
mounting the detector, the lens must be removed.
lar cover ring must be removed prior to assembly. To do this,
twist the circular cover ring of the PD2 anticlockwise through
approximately 5° and lift off.

Having connected up the wires in accordance with
regulations, put on the cover ring by turning in a clockwise
direction. Apply mains voltage.

4b. Mounting

A circular opening of diameter 68mm must be produced in the
ceiling. Having connected up the cables in accor dance with
regulations, the detector is inserted into the opening as shown in
the drawing opposite and fixed into position with the assistance of
the spring clips.

FC

68 mm

In Master-/Slave-operation the master device must
always be installed at the site with less daylight.

The light sensor should be mounted on the opposite
side of the window.

The circu-

®

PD4-M-DALI/DSI/PD4-S

PD4-M-DALI/DSI-SM/FC

5a. Position DIP-Switches, LEDs and

Potentiometer SM

Light measurement

CBA

Light measu­rement

I II III

C
B

1

A

2

PD4-

Surface

mounting

5b. Position DIP-Switches, LEDs and

Potentiometer FC

3

1

2

DIP

3

PD4-

False ceiling

mounting

I II III

DIP

6. Self test cycle/Startup behavior

The product enters an initial 60-second self-test cycle, when the
supply is first connected. During this time the device does not
respond to movement and stays on.

The initialization mode can be changed by using the remote control

7. Putting into operation / Settings

Follow-up time for light control

The time can be set infinitely variably between
1 and 30 minutes.

Symbol TEST: Test mode
Every movement switches on the light for a period of 1
second, switching it off for a period of 2 seconds.

Twilight-switch for light control (relay 1)

The switch-on value for the light can be set at between
10 and 2000 Lux. Using the rotary control, the luminan
ce set points can be set as desired.

Symbol
Symbol : Daytime operation

Orientation lighting

The orientation lighting can be set infinitely variably at
between 5 and 60 minutes resp. "ON" for permanent
orientation lighting or "OFF" for no orientation lighting.
"ON" for permanent orientation lighting
"OFF" deactiviation of orientation lighting.

Pulse spacing PD-Slave

9s 2s

2 or 9 seconds can be set for the pause between 2
pulses sent to the master. The setting can be made with
activated (

LED ON

For devices with a separate Slave input, 2 sec.
can be set.

(INI-ON or INI-OFF)

: Night-time operation

) or deactivated ( ) LED indicator.

DIP-switch function

DIP 1 Fully automatic mode

(VA)

Semi automatic
mode (HA)

DIP 2 LED ON LED OFF

DIP 3 operation mode DALI operation mode DSI

Potentiometer A Brightness constant light control
Potentiometer B Off delay for light
Potentiometer C Orientation lighting

LED I green
LED II red
LED III white

8.

Wiring diagram

Standard mode with Master/Slave

L

N

LN RS + -

DALI

-

Connected Slaves must have the same phase
as the Master.

N
DA
DA

L

E1 DALI/DSI

9. Manual switching and dimming

By pressing the push button, the phase can be given to the S
terminal.

To turn on or off, press the push button briefly. The light will
remain on or off, as people are detected plus the follow-up time.

With a long key press the light will dimmed manually. When
you release the button, the current brightness value is retained.
With renewed dimming, the dimming direction is reversed.

NLR

10. Range

quer zum Melder gehen
frontal zum Melder gehen
Unterkriechschutz

PD4

1

360°

6,40 m

8 m

2

24 m

1

Walking across
Walking towards

2

Seated

2,50 m

24 m

11. Exclude sources of interference

If the detection zone is too large, or areas covered that should not
be monitored, use the blinds to reduced or limited those areas.

12. Technical data

Power supply: 110-240V~, 50/60 Hz
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class:
Max. no. of series-connected
electronic ballasts: up to 50 (Broadcast)
Recommended height
for mounting:
Range of coverage Ø
H 2,5 m / T = 18°C: seated 4 m / tangential 10 m /

Area of coverage:
Dimensions H x Ø [mm]

50x97 84,5x74mm

2 - 3m

IP20 / II

radial 6m

circular 360°

SM FC

Technical data PD4 S lave

Power supply: 110-240V~, 50-60 Hz
Impulse output: Optocoupler max. 2W
Impulse duration: 2 sec. or 9 sec.
Dimensions: see above

Declaration of Conformity:

voltage recommendation 2006/95/EC and the EMV recommen­dation 2004/108/EC.

WE RECOMMEND THAT BEFORE DIMMING OF THE CONNECTED
LIGHTS A 100 h BURN IN (T5 TUBES OR 80 HOURS FOR T8 TUBES)
FUNCTION TAKES PLACE.

THE LIFESPAN OF THE LAMPS CAN BE REDUCED IF THE BURN IN
DOES NOT TAKE PLACE.

The product complies with the low

14. LED-functional indicators

LED-functional indicators

Process Standard mode Double-locked

Initialisation time
unprogrammed

Initialisation time
programmed

Motion detection

Too bright detected

Too bright / too dark /
undefined in opened state

Switching DALI/DSI
DSI active

Switching DALI/DSI
DALI active

Switching HA/VA
VA active

Switching HA/VA
VA active

Switching Preset/User
Preset active

Switching Preset/User User
active

IR signal valid received

IR signal invalid received

100h Function active

Light measurement in
progress

Red flashes Green flashes

Red flashes
quickly

Red flashes on
each detected
movement

Red flashes 2x
each second

Red flashes
very quickly

Red shines
3 sec.

Green shines
3 sec.

Red shines
3 sec.

Green shines
3 sec.

Red shines
3 sec.

Green shines
3 sec.

Red and white
shines 3 s

Red shines
0,5 sec.

Red / Green
flashes
variable

Green shines
1x in 10 sec.

Green flashes
quickly

Green flashes
on each detec
ted movement

Green flashes
2x each second

Green flashes
very quickly

Red / Green
flashes
variable

Green shines
1x in 10 sec.

-

13. Article / Part nr. / Accessory

Typ SM FC FM

PD4-Master-DALI/DSI 92279 92 275 -

PD4-Slave 9214 2 92254 9 2163

®

Remote control:

LUXOMAT

IR-PD-DALI (incl. wall bracket) 92094

Accessory:

BSK Ball basket guard 9219 9
SM-Socket IP54 92161

13. S ettings by remote control when open

!

max

50

Lux

1500

Lux

ON

max

50

Lux

1500

Lux

1500

Lux

!

!

1500

Lux

Settings with remote control override the potentiometer
and DIP settings.

The DIP settings are reactivated by

• Reset with Test-Sun setting at the potentiometers

• „RESET“ in the opened state

Remote control LUXOMAT

®

IR-PD-DALI

1. Check Battery:

Open battery compartment by pressing
the plastic springs together and remo­ving the battery-holder.

2. Note:

The operable distance of the remote control depends on the
brightness. The brighter the less distance the remote could reach
the occupancy detector. The setting for "SUN" could only be set
with the potentiometer.

By using the remote control IR-PD-DALI, we recommend to set
potentiometer 2 on "SUN". Pushing the RESET button (remote
control) would reset the brightness independence of the occu­pancy detector (SUN).

IR-PD-DALI

Wall bracket for
remote control IR-PD-DALI

14. Settings by remote control when open

Unlocking device
– Activation of the
programming mode

Resetting
when open:

Deletes all
values set with
the remote
control, light
OFF.

+

DSI/

DALI

or

or

Switching between DSI
and DALI program
The Factory setting
is DALI

Dimming of the
lighting on the
desired luminance
value

Automatic reading
in the current light
value as new lumi­nance set point

Adjusting of the
luminance set point

–

from 50 to 1500 Lux

+ / – small steps

/ – big steps

+

Follow-up time

30

min

light

OFF

Orientation lighting
on/off

Orientation lighting

10

and its

min

follow-up time

Preset/user mode

Fully automatic /
semi automatic mode

Start Light mesaruement
by holding down the
push button

1

at

min

optionaloptionaloptionaloptional

ON

1

at

min

Exit programming mode

If there is no entry
for about 3 min.
the programming
mode is ended
automatically.

optional

t < 5 s

LED ashes

Permanent protection
against sabotage

With this function,
the detector is per­manently locked. This
mode can only be
activated for 5 s after
closing the detector.
In this mode, only the
function

„Light on /

Light off“ activated.

18. Light regulation

The detector has two integrated light control algorithms. The set

value for the rst algorithm is adjusted by potentiometer (LUX)

on the device. Very small light amounts, which shine directly to
the detector, have the result of a trigger under control of the set
value.

The second algorithm has an integrated daylight compensation.
Therefore it is necessary, that the detector analyzes the switched
light quantity. This algorithm can only be used by remote control.
The programming of the setpoint value and the measurement of
the light quantity in two steps:

In the open state

• The set value will be without daylight (no light in room)
adjusted by using the remote control.

• Measuring the light quantity, will be initiated by a long
press (> 3 sec) at the test button. The detector turns the
light on for 5 min. up to 100%. Then the light will be
on and off for a short time and stays on after that. This

measuring process is shown by a ashing green LED (10

sec on / 1 sec on). This measuring process is required for
each change of the set value.

If the measuring process is not performed, the detector
performs this automatically, when the ambient light is for

1 h less than 50 LUX.

19. Fully / Semi automatic mode

The system switches over when the “Light” push-button
is open.Each time a push button is pressed, the current
operating mode is indicated by the red LED:
Red lights for 3 sec. = Fully automatic mode
Green lights for 3 sec. = Semiautomatic mode

Fully automatic operation

In this operating mode, the lighting switches automatically on
and off for increased comfort, depending on presence and
brightness.

Semi automatic operation

In this operating mode the light turns on only after a manual
switching, for a increased savings success. Switching off is
automatically or manually.

19. Settings during the Self-test cycle

In the rst 60 seconds after connecting the AC voltage, the

following functions can be set:

INI-OFF/ON-Mode:

Turn off or turn on the detector during the self-test cycle
of 60 sec. The final state is active. Factory settings of the
light is on during initialization.

Initialization mode INI-OFF the detector does not turn on
after the power supply voltage. A movement switch on
the detector after 60 seconds.

Startup behavior:

The setpoint value can be started after switching on in
two ways. The detector switches the lights on to 10%
and then adjusts upward (min button) or it switches the
light on 100% and regulates down (max button). This
is confirmed by a short flashing of red and white LED
lighting. By factory default setting, detector switches the
light to 100% and regulates toward the set point.

20. Self-test cycle/Reset

Testmode

Disable the test mode

Resetting when closed

The lighting relay is switched off, i.e. opened and the
follow-up times reset.

21. 100h Function

(long press when closed)

T5 and T8 are recommended to burn-in for 100h at maximum
brightness before dimming. This would prolong the life of the
lamp.

At the 100h-Function the detector only switch on and off. A
regulation to a set value will be suppressed. The light has to be
on for 100h, until the set value get regulated.

The 100h will be activated by pressing a long button press
(>3 sec.). An activated time can be stopped by pressing a long
button press again. The red/green LED shows if the function gets
activated.

Before you can dimmed analog or digital, is a suppres­sion of the dimming function for 100h at T5-or 80h at T8

uorescent lamps and 100% of nominal light necessary.

Failure to comply to the 100h burn-in would lead to the shorten
of the life of the lamp. Conditional random variations in light
intensity can be the result.

22. Manual Switching

(short press when closed)

You can switch the lighting on and off manually by pressing
the pushbutton for a short time. It will stay on or off as long

as people are detected plus the congued follow up time.

23. Manual Dimming – Preset/User

You can dim manually by pressing the push button for a long
time (> 2sec.). When the button is released, the current dim­ming value is retained. Upon renewed dimming, the dimming
direction is reversed.

Two different operating modes are selected
in the opened state.

The system switches over when the "Doublelock" push-button is
open (see remote control functions, page 1). Each time a push­button is pressed, the current operating mode is indicated:

Red lights for 3sec. = Preset
Green lights for 3sec. = User

PRESET – the luminance set point is set during start-up operation
by the installer and remains unchanged. The luminance set-point

congured through manual dimming is only applied for the time

being.

The constant light regulation is now deactivated! The current set

articial light is retained independent of the ambient/daylight

brightness! After switching off and then back on, the original
set luminance set-point is reset = constant light regulation is
activated.

USER – can only be activated via the remote control!

The luminance set-point is changed upon each manual dimming
and re-adjusted by the user. The constant light regulation
remains activated!

24. Reset the detector

If the permanent sabotage protection is activated,
the detector can be released again as follows:

• Switch off the power supply and switch it back on

• Let the sensor to initialize for 31 to 59 secs.

• Switch off the power supply again

• Apply power again and wait for for the self testing

• Press the unlock
With this procedure, the remote control programmed values are

not deleted (before activation of the sabotage protection).
Alternatively, the detector can be reset in this way:

• Switch off the power supply

• Set potentiometer 1 to "test" and potentiometer 2 to "SUN"

• Apply operating voltage

Except of the INI ON/OFF setting, the detector will be reset to
factory setting or the setting of the potentionmeter.

Pushing the "RESET" button on the remote control, in opened
mode, will delete all of the values which was set by the remote
control (beside of INI ON/OFF) and set the detector back to
it‘s factory reset.

_PD4-M-DALI/DSI_EN_270314_1

8158

MAN