B.E.G. LUXOMAT PD4-M-DALI/DSI-SM, LUXOMAT PD4-M-DALI/DSI, LUXOMAT PD2-M-DALI/DSI-SM, LUXOMAT PD2-M-DALI/DSI-FC, LUXOMAT PD4-M-DALI/DSI-FC Installation And Operating Instruction

25

22

18

1

6

10

3

1

TEST

6

30

R1

120

60

50

40
30

15

10

A

16

10

5

2
1

30

15

TEST

2000

1200

600

200

40

5

25

22

18

1

6

10

3

1

TEST

6

30

R1

2000

1200

600

200

40

max

50

Lux

1500

Lux

50

Lux

1500

Lux

50

Lux

1500

Lux

50

Lux

1500

Lux

max

50

Lux

1500

Lux

ON

max

50

Lux

1500

Lux

1500

Lux

25

22

18

1

6

10

3

1

TEST

6

30

R1

120

60

50

40

30

15

10

A

16

10

5

2

1

30

15

2000

1200

600

200

40

5

60

5

10

30

50

ON

OFF

GB

LUXOMAT

Installation and Operating Instruction for B.E.G. - Occupancy detectors PD2-M-DALI/DSI-SM/-FC and
PD4-M-DALI/DSI-SM/-FC

1a. Features

*

For connection of up to 25 lamps
in FC-version and up to 12 lamps
SM-version

* Suitable for dimmable electronic

ballasts and control modules
* DALI output
* Constant light control
* Manual switching /dimming
* Semi or completely automatic

operation

Luminance (brightness) set point,

*

switch-off delay time for LIGHT and

orientation-light adjustable
* Sensor and power sections in one

housing
* Infrared remote control

2c. Self test cycle

2000

1200

600

200

40

The product enters an initial 60-second
self-test cycle, when the supply is first
connected. The occupancy detector is
ready for operation.

1b. Mounting preparations

Work on the 230V mains supply
may only be carried out by quali­fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec­trical personnel in accordance with
electrotechnical regulations.

Disconnect supply before installing!

When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.

3. Inbetriebnahme / Einstellungen

Follow-up time for light control

The time can be set infinitely variably at between
1 and 30 minutes.

Symbol TEST: Test mode (Every movement switches on
the light for a period of 1 second, switching it off for a
period of 2 seconds after that regardless of the level of
brightness.)

Twilight-switch for light control (relay 1)

The switch-on value for the light can be set at between 10
and 2000 Lux. Using the rotary control, the luminance set
points can be set as desired.

Symbol

: Night-time operation

Symbol

Orientation lighting

This rotary controller serves to determine the working time
of the orientation lighting (fixed to 20%).
“ON” for permanent orientation lighting.
“OFF” for deactiviation of orientation lighting.

: Daytime/ Night-time operation

PD2/PD4-M-DALI/DSI

2a. Installation of the LUXOMAT® PD2/PD4-M-

DALI/DSI-SM

C

close

open

D

The detector must be in stalled on a solid and level surface.
The circular cover ring must be removed prior to assembly.
To do this, twist the lens (C) of the PD4 or (D) of the PD2
anticlockwise through approximately 5° and lift off.

Having connected up the wires in accordance with regula­tions, secure the detector with 2 screws. After installation
replace the lens and lock (turn clockwise). Mains to be
connected.

4. Settings carried out using remote control (optional)

Remote control LUXOMAT® IR-PD-DALI

1

2

1 2

2b.

Installation of the LUXOMAT®

PD2/PD4-M-DALI/DSI

A circular opening of diameter 68 –
70mm must be produced in the ceiling.
Having connected up the cables in accor­dance with regulations, the detector is
inserted into the opening as shown in the
drawing opposite and fixed into position
with the assistance of the spring clips.

1. Check Battery:
open battery compartment by pressing the plastic
springs together and removing the battery-holder.

2. IMPORTANT

Please pay attention, that the setting is Potentio­meter 1 at “TEST” and Potentiometer 2 not at
“SUN”. All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position “TEST/
SUN”. Please switch Potentiometer 2 over to
“MOON” or any other value.

Caution:
Settings with remote control supersede the settings
by courtesy of potentiometers.

®

-FC

Option:

Wall bracket for remote control
IR-PD-DALI

Unlocking device

DSI /
DAL I

+

–

ON

20 %

OFF

Lock device

Switching between DSI and DALI program

Factory setting DSI, press 1x DALI, press 2x DSI /DALI
(Toggle-function)

Luminance set point for constant light regulation
+ / – small steps

Dimming

The following approach will prove useful when setting a
command value (example workplace): Place a luxmeter flat
on the desk, then, using the remote control IR-PD-DALI, adjust
the light up or down by pressing the keys max or min until
the desired command value which best suits your require­ments has been reached.

Automatic reading in the current light value
as new luminance set point

Individual light value 2 - 2500Lux

Follow-up time (relay and channel 1)

1 up to 30min.

Orientation lighting and its follow-up time
OFF button: No orientation light
Grey button: Programming the switch-off delay time
On button:

Note: During the orientation light phase, the constant light reg­ulation is also active: if there is sufficient brightness, dimming
occurs < 2V and, if applicable, the lighting is switched off.

/ – big steps

+

Orientation light is permanently activated.

Preset/ user mode => (see page 2, point 6)

Fully automatic/semi automatic mode => (see page 2, point 5)

Semi automatic: green LED,
Fully automatic: red LED on for approx. 3sec.

Resetting when open

All values which have been programmed using the remote
control IR-PD-DALI are deleted, and those values which have
been set by potentiometer are activated.

Lock device

Test mode

Reset to deactivate

Resetting when closed

The lighting relay is switched off, i.e.
opened and the follow-up times reset.

Permanent protection against sabotage

This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
during the period of 5 seconds after pressing the “lock“
button. This status will only permit actuating the function
“Light on/ Light off”.

The procedure for leaving this mode is as follows:

1. Switch off the current

2. Apply current for 31 - 59 seconds

3. Switch of the current again

4. Apply current

5. Open detector

Light on/ off

The light will remain switched on/off for as long as move­ments are detected in the areas of coverage. Once the last
movement has been detected, the light will remain on for
the duration of the follow-up time as per setting.
The appliance will then return independently to the mode
selected (Fully or Semi-automatic).

1500

Lux

1500

Lux

quer zum Melder gehen
frontal zum Melder gehen
Unterkriechschutz

5. Fully / Semi automatic mode

(for IR-PD-DALI functions see page 1)

Fully automatic operation

In this operating mode, the lighting switches automati­cally on and off for increased comfort, depending on
presence and brightness.

Semiautomatic operation
(Semiautomatic can only be activated via the remote
control!)

In this operating condition, in order to gain increased
savings, the lighting is energized only after being manu­ally switched on.
Switch-off takes place automatically.
The semiautomatic mode basically behaves like the fully
automatic one. However, the difference is that switching­on must always be carried out manually!

As many (closer-contact) buttons as desired can be wired
in parallel on the “S” button input (ON/ OFF Dimm).

6. Manual Dimming - Preset / User

(for IR-PD-DALI functions see page 1)

You can dim manually by pressing the pushbutton for
a long time (> 2 sec). When the button is released,
the current dimming value is retained. Upon renewed
dimming, the dimming direction is reversed.

PRESET – the luminance set point is set during start-up
operation by the installer and remains unchanged.

The luminance set- point congured through manual

dimming is only applied for the time being.
Caution:
The constant light regulation is now deactivated!

The currently set articial light is retained independent

of the ambient/daylight brightness!
After switching off and then back on, the originally set
luminance set-point is reset = constant light regulation
is activated.

USER - can only be activated via the remote control!
The luminance set-point is changed upon each manual
dimming and re-adjusted by the user (Conformation
through relay clicking!).
The constant light regulation remains activated!

7. Manual Switching

You can switch the lighting on and off manually by
pressing the pushbutton for a short time. It will stay on or

off as long as people are detected plus the congured

follow up time.

8. Range of Coverage

PD2-M-DALI/DSI

2.50 m

10 m

PD4-M-DALI/DSI

2.50 m

1

360°

2.50 m
6 m

2

10 m

2

24 m

360°

1

6.40 m
8 m

24 m

9. Wiring diagram

Terminal connection for MASTER-/SLAVE-operation

L
N

DALI-EVG 1

230V

MASTER

R S N L DALI

PD2/PD4-M-DALI/DSI-FC = up to 25 / PD2/PD4-M-DALI/
DSI-SM = up to 12 electronic ballasts (EB) are connectable.

10.

PD2/ PD4-M-DA LI/DSI

N – N L – L R – R

~

SLAVE

DA DA

DALI-EVG 2-25

230V

DA DA

~

T5 und T8

uorescent

lamps

- Connections

Connections PD2/PD4-M-DALI/DSI-SM

SLAVE

+

–

NLS R

L N

DALI

Connections PD2/PD4-M-DALI/DSI-FC

SLAVE

+

–

N LSR

DALI

11. Article / Part nr. / Accessory

Type SM FC

PD2-M-DALI/DSI-Master 92280 92258

PD4-M-DALI/DSI-Master 92279 92275

PD2-Slave 92152 92166

PD4-Slave 92142 92254

®

LUXOMAT

Remote control:

IR-PD-DALI (incl. wall bracket) 92094

Accessory:

BSK Ball basket guard 92199
Wall bracket for remote control as replacement
SM-Socket IP54 92161

92100

12.

Technical data PD2/ PD4-M-DA LI/DSI

Sensor and power supply in one case

Power supply: 230V~ +6 %/-10%
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class:

accessory IP54, PD2/PD4-M-DALI/DSI-FC IP20 / II

Settings:

locally and by remote control

Light values - IR-PD-DALI:
Extension of the detection area:
Area of coverage:
Range of coverage Ø H 2.50m / T=18°C:

PD2-M-DALI/DSI seated 2.50m / tangential 10m / radial 6m
PD4-M-DALI/DSI seated 6.40m / tangential 24m / radial 8m

Recommended height for mounting:
Light measurement: mixed light, daylight + artificial light
Lux values-Potentiometer:

• DALI-Output

digital BUS control wire, 2-core, no polarity (broadcast only)

Max. no. of series-connected electronic ballasts:

PD2/PD4-M-DALI/DSI-DE up to 25
PD2/PD4-M-DALI/DSI-AP up to 12

Time-settings:
Dimensions Hx Ø [mm]

PD2-M-DALI/DSI 50x 98 84,5 x 80
PD4-M-DALI/DSI 76 x 101 97x 103

Technical data PD2/PD4-Slave

Electrical data same as above, but just one channel for
signaling motion detection.

the low voltage recommendation 2006/95/EC and the
EMV recommendation 2004/108/EC.

1 - 30min. / test

Declaration of Conformity:

PD2-M-DALI/DSI-SM IP20, with

50 - 1500Lux

circular 360°

with Slaves

2 - 3 m

10 - 2000Lux

SM FC

The product complies with

13. LED-functional indicators, fault-finding

The functional indicators in the case of the LUXOMAT®
PD2/PD4-M-DALI/DSI-MASTER (red and green LED‘s)

Red LED indicating self-checking mode (over a period
of 60 seconds following mains-supply lock-on)

Flashing at intervals of 1 second
EEPROM/ memory empty

Flashing rapidly

EEPROM/ memory contains information

Red LED as an indicator of status

Flashing irregularly

Movements are detected within the area of coverage

Flashing regularly

Detector identifies bright, light off
(dependent upon operating mode)

Not illuminated

Detector identifies dark, light on
(dependent upon operating mode)

Flashing extremely rapidly

Too bright / Too dark / Undefined

Red LED as an acknowledgement of receipt for
commands from the remote control

Illuminated for 2 seconds

Signal validly received

Illuminated for 0.5 seconds

Not-accepted command, detector blocked
Flashing extremely rapidly

Not-accepted command, occurs, for example, when
an attempt is made to input twilight-value are too
bright or too dark

Green LED as an acknowledgement of receipt for
commands from the remote control

Lights up for 3 seconds

Semi automatic or user signal correctly received

Green LED as an indicator of status (only for status
“Permanent protection against sabotage”)

Flashing irregularly

Movement are detected within the area of coverage

Flashing regularly

Detector identifies bright, light off
(dependent upon operating mode)

Not illuminated

Detector identifies dark, light on
(dependent upon operating mode)

lluminated for 2 seconds

Signal validly received
(dependent upon operating mode)

1
2

walking across
walking towards
seated

MAN 5632 – 141209-4