3. Putting into operation / Settings
Self test cycle
The product enters an initial 60-second self-test cycle, when
the supply is first connected. The occupancy detector is ready
for operation.
Follow-up time for light control
The time can be set infinitely variably at between
15 seconds and 16 minutes.
Symbol
: Impulse < 1sec.
Symbol
TEST: Test mode (Every movement switches on the
light for a period of 1 second, switching it off for a period of
2 seconds after that regardless of the level of brightness.)
Twilight-switch for light control (relay 1)
The switch-on value for the light can be set at between 10
and 2000 Lux. Using the rotary control, the luminance set
points can be set as desired.
Symbol
: Night-time operation
Symbol
: Daytime/ Night-time operation
Follow-up time for appliance-control
The time can be set infinitely variably at between 5 minutes
and 120 minutes. There is a period of delay prior to switch-on
of between 5 - 10 minutes for times set in excess of 15 minutes.
Symbol : Impulse = 1sec.
Symbol A: Alarm impulse = 1sec.
Installation and Operating Instruction for B.E.G. - Occupancy detectors PD1-M-2C/-S-SM/-FC/-FM
2a.
Installation of the LUXOMAT® PD1-M-2C/-S-SM
2b. Installation of the LUXOMAT
®
PD1-M-2C/-S-FC
4.
PD1-M-2C: Settings carried out using remote control (optional)
Remote control LUXOMAT® IR-PD
1. Check Battery:
open battery compartment by pressing the plastic
springs together and removing the battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentiometer 1 at “TEST” and Potentiometer 2 not at
“SUN”. All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position “TEST/
SUN”. Please switch Potentiometer 2 over to
“MOON” or any other value.
Caution:
Settings with remote control supersede the settings
by courtesy of potentiometers.
1. Mounting preparations
Work on the 230V mains supply
may only be carried out by qualified professionals or by instructed
persons under the direction and
supervision of qualified skilled electrical personnel in accordance with
electrotechnical regulations.
Disconnect supply before installing!
When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
during the period of 5 seconds after pressing the “lock“
button. This status will only permit actuating the function
“Light on/Light off”.
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
5. Open detector
Light on/ off
The light will remain switched on/ off for as long as movements are detected in the areas of coverage. Once the last
movement has been detected, the light will remain on for
the duration of the follow-up time as per setting.
The appliance will then return independently to the mode
selected (Fully or Semi-automatic).
Option:
Wall bracket for remote
control IR-PD
2c.
Installation of the LUXOMAT®
PD1-M-2C/-S-FM
IR-PD
IR-PD-Mini
B.E.G.
LUXOMAT® PD1-M-2C/PD1-S
The detector can
be installed in
conventional inletsockets mounted
on the ceiling.
The assembly
plate enclosed
must be stripped
off prior to installation and secured
to the ceiling
using 4 screws
and ensuring that
it is not laterally
transposed.
For surface-mounting, an inwall sensor unit is combined with a surface-mounted
receptacle as a housing base.
Before mounting the base, the enclosed mounting plate must be mounted true to
side, i.e. the writing must be legible.
Now fix the base on ceiling or wall, but first put the cable through one of the
cable openings provided. The detector must be mounted on a flat, solid surface.
Next prepare the sensor part by screwing in both fixing screws, then connect the
cable as per the wiring diagram.
Now insert the sensor part and check for matching positioning
of the two markings.
Press beyond the spring housing pressure so that the sensor
part firmly locks in place.
Now turn the sensor part counter-clockwise for about 10° to
the stop.
The detector has
been designed and
developed specifically
for installation in suspended ceilings.
A circular opening of
diameter 68 – 70mm
must be produced in
the ceiling.
Having connected up the cables in accor dance
with regulations, the detector is inserted into
the opening as shown in the drawing opposite
and fixed into position with the assistance of the
spring clips.
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
2000
1200
600
200
40
5
1
1 2
2
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
2000
1200
600
200
40
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
5
120
60
50
40
30
15
10
A
5
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
5
120
60
50
40
30
15
10
A
16
10
5
2
1
30
15
TEST
5
B.I.T.
Q.C.
PASSED
1
GB
6 mm
Having connected up the cables in accordance with regulations, the detector
can be placed in position as shown in
the drawing opposite and, applying
a little pressure, can then be locked
into position with the assistance of the
spring clips.
Unlocking device
Lock device
Luminance set point
Automatic reading in the current light value
as new luminance set point
Individual light value 2 - 2500Lux
Follow-up time (relay and channel 1)
15sec. up to 30 min.
Impulse function (relay and channel 1)
1sec. ON, 9 sec. OFF
Time setting (relay and channel 2)
5 min. up to 120 min.
Impulse function (relay and channel 2)
The voltage-free contact is closed for a period of 2 seconds.
This is followed by a period of idle time of 8 seconds’ duration.
Alarm impulse program for appliance control (relay 2)
The relay will not close until at least three movements have been
registered over a period of 10 seconds (impulse = 1 second).
Preset/ user mode
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: red LED (ashing),
Fully automatic: red LED on for approx. 3sec.
Resetting when open
All values which have been programmed using the remote
control IR-PD are deleted, and those values which have
been set by potentiometer are activated.
A
3
1500
Lux
R1
R2
Sensor and power supply in one case for onwall-, ceilingand flushmounting
Power supply: 230V~ +6 %/-10%
Power consumption: < 1W
Ambient temperature: -25°C to +50°C
Degree of protection/class: SM IP54, FC and FM IP20, FC
with accessory IP23 / II
Settings: manually and by remote control
Light values: 20 - 1000Lux (Remote control)
Extension of the detection area: with Slaves
Area of coverage: square 4 x 90°
Range of coverage Ø H 2,50m / T= 18°C:
seated 4.20m / tangential 7.50m / radial 4.50 m
Recommended height for mounting: 2 - 3 m
Light measurement: mixed light, daylight + artificial light
Lux values: 10 - 2000Lux (Potentiometer)
• Relay/Channel 1 for light-connection
Type of contact: dry contact type NO
Contact load: 2300W cos (ϕ)=1 / 1150VA cos(ϕ) = 0.5
Time-settings: 15sec. - 16min. (30min. with remote
control) / Test
• Relay/Channel 2 for HVAC
Contact load: 230V~, 3 A cos(ϕ) =1
Time-settings: 5 min. - 120min. with time delay of 5 min.
for follow-up time > 15min.
Dimensions
H x Ø [mm]
SM FC FM
PD1-M-2C 80 x 98 84 x98 65 x 98
Visible portion when built into ceiling: 30 x 98mm
Technical data PD1-Slave
Electrical data same as above, but just one channel for
signaling motion detection
Declaration of Conformity: The product complies with
the low voltage recommendation 2006/95/EC and the
EMV recommendation 2004/108/EC
11.
Technical data PD1-Master-2C
10. PD1-M-2C - Connections
Type SM FC FM
PD1-M-2C (Master) 92177 92174 92170
PD1-S (Slave) 92178 92175 92172
LUXOMAT
®
Remote control:
IR-PD (incl. wall bracket) 92160
IR-PD-Mini 92159
Accessory:
BSK Ball basket guard 92199
Wall bracket for remote control as replacement
92100
Blinds 92260
Occupancy detectors - Covering IP23 92206
SM-Socket for PD1-FM 92171
8. Article / Part nr. / Accessory
MAN 6316 – 211209–1
7. Range of Coverage
5. Fully / Semi automatic mode
(for IR-PD functions see page 1)
Fully automatic operation
In this operating mode, the lighting switches automatically on and off for increased comfort, depending on
presence and brightness.
Semiautomatic operation
(Semiautomatic can only be activated via the remote
control!)
In this operating condition, in order to gain increased
savings, the lighting is energized only after being manually switched on. Switch-off takes place automatically.
The semiautomatic mode basically behaves like the fully
automatic one. However, the difference is that switchingon must always be carried out manually!
As many (closer-contact) buttons as desired can be wired
in parallel on the “R” button input (ON/ OFF).
6. Manual Switching
You can switch the lighting on and off manually by
pressing the pushbutton for a short time. It will stay on or
off as long as people are detected plus the congured
follow up time.
12. LED-functional indicators, fault-finding
The functional indicators in the case of the LUXOMAT®
PD1-M-2C (red and green LED‘s)
Red LED indicating self-checking mode (over a period
of 60 seconds following mains‘-supply lock-on)
Flashing at intervals of 1 second
EEPROM/ memory empty
Flashing rapidly
EEPROM/ memory contains information
Red LED as an indicator of status
Flashing irregularly
Movements are detected within the area of coverage
Flashing regularly
Detector identifies bright, light off
(dependent upon operating mode)
Not illuminated
Detector identifies dark, light on
(dependent upon operating mode)
Flashing extremely rapidly
Too bright / Too dark / Undefined
Red LED as an acknowledgement of receipt for
commands from the remote control
Illuminated for 2 seconds
Signal validly received
Illuminated for 0.5 seconds
Not-accepted command, detector blocked
Flashing extremely rapidly
Not-accepted command, occurs, for example, when
an attempt is made to input twilight-value are too
bright or too dark
Lights up for 3 seconds
Fully automatic mode
Flashing for 3 seconds
Semi automatic mode
Green LED as an indicator of status (only for status
“Permanent protection against sabotage”)
Flashing irregularly
Movement are detected within the area of coverage
Flashing regularly
Detector identifies bright, light off
(dependent upon operating mode)
Not illuminated
Detector identifies dark, light on
(dependent upon operating mode)
lluminated for 2 seconds
Signal validly received
(dependent upon operating mode)
7.50 m
4.20 m
7.50 m
4 x 90°
2.50 m
1
2
1
quer zum Melder gehen
frontal zum Melder gehen
Unterkriechschutz
Walking across
Walking towards
Seated
1500
Lux
1500
Lux
Connection PD1-M-2C
NONO
NR L L
SLAVE
L'
3A
2
9. Wiring diagrams
Standard operation, manual switching possible
(NO-contact to be pressed for approx. 1sec.). The
potentiometers not to be set on “Test“ or “Sun“
otherwise the preadjusted values will get lost during
this manual operation.
Master-/Slave-operation, i.e. Masters operate as Slaves but with additional push button
function to switch the light manually. The preset
values will not get lost. The Master is the only unit to
read in the levels and to switch the connected loads.
The Slave units will react on motion only, independently of the Lux levels, by sending an impulse via the
dry contact, to the Master.
Terminal connection for Master-/Slave-operation
R 2
MASTER MASTER/SLAVE
modus
Master-/Slave-operation with one Master
and several Slaves. The Master is the only unit
to read in the Lux levels and to switch the connected
loads. The Slave units will react on motion only, independently of the Lux levels, by sending an impulse
via the dry contact, to the Master.
Terminal connection for standard operation
HVAC
MASTER
HVAC
SLAVE
MASTER
Terminal connection for Master-/Slave-operation
Standard operation with external push button
HVAC
MASTER
Standard operation
3
3
Loading...