Beckhoff CP7103, CP7111, CP7110, CP7112, CP7113 Installation And Operating Instructions Manual

Installation and Operating instructions for

Panel-PC CP71xx

Version: 1.2
Date: 2006-03-06

Table of contents

Table of contents

1.

General Notes 3

Notes on the documentation 3
Liability conditions 3
Description of safety symbols 3
Basic safety measures 4
Operator's obligation to exercise diligence 5
Operator requirements 5

2.

Product Description 6

Appropriate Use 6
Structure 6

Access to the drives 7

Interfaces 8

USB interfaces 8
Network connection 8
Serial interface 8
DVI-I interface (in use) 8
USB interface (in use) 8
Serial interface (in use) 8
Additional plug-in cards (optional) 8

3.

Installation Instructions 9

Transport and Unpacking 9

Transport 9
Unpacking 9

Installation of the PC 10

Earthing measures 10

Power Supply Connection 11
Electrical data 11

Pin assignment of the connector 11

Fitting the cable 12

Assembling the connector 12

Connecting Power Supply 13

Cable Cross Sections 13
PC_ON, Power-Status 13
Wiring diagram 13

Connecting devices 14

Connecting cables 14
Check voltage rating and connect 14

4.

Operating Instructions 15

Switching the Industrial PC on and off 15

First switching on and driver installation 15

UPS Software Components (optional) 16

Installation on the PC 16
Help files 16

Maintenance 17

Cleaning the Industrial PC 17
Replacing the battery on the motherboard 17
Servicing 17

Shutting down 17

Disposal 17

5.

Troubleshooting 18

Fault correction 18
Service support 19

Beckhoff Service 19
Beckhoff Support 19
Company headquarters 19

CP71xx 1

Table of contents

6.

Assembly dimensions 20

7.

Appendix 21

Technical data 21
Approvals 21

FCC: Federal Communications Commission Radio Frequency Interference
Statement 21
FCC: Canadian Notice 21

2 CP71xx

General Notes

General Notes

Notes on the documentation

This description is only intended for the use of trained specialists in control
and automation engineering who are familiar with the applicable national
standards. It is essential that the following notes and explanations are
followed when installing and commissioning these components.

Liability conditions

The responsible staff must ensure that the application or use of the
products described satisfy all the requirements for safety, including all the
relevant laws, regulations, guidelines and standards.

The documentation has been prepared with care. The products described
are, however, constantly under development. For this reason, the
documentation may not always be have been fully checked for consistency
with the performance data, standards or other characteristics described.
None of the statements in this manual represent a guarantee for as set out
in § 443 of the German Civil Code or a statement about the assumed use
according to the contract as set out in § 434 para. 1 clause 1 no. 1 of the
German Civil Code. In the event that it contains technical or editorial errors,
we retain the right to make alterations at any time and without warning. No
claims for the modification of products that have already been supplied
may be made on the basis of the data, diagrams and descriptions in this
documentation.

© This documentation is protected by copyright. Any reproduction or third
party use of this publication, whether in whole or in part, without the written
permission of Beckhoff Automation GmbH, is forbidden.

Description of safety symbols

i

Danger

Warning

Note

The following safety symbols are used in this operating manual. They are
intended to alert the reader to the associated safety instructions.

This symbol is intended to highlight risks for the life or health of personnel.

This symbol is intended to highlight risks for equipment, materials or the
environment.

This symbol indicates information that contributes to better understanding.

CP71xx 3

General Notes

Basic safety measures

Only switch the PC off after
closing the software

Warning

Before the Industrial PC is switched off, software that is running must
be properly closed.

Otherwise it is possible that data on the hard disk is lost. Please read the
section on Switching the Industrial PC on and off.

Switch off all parts of the equipment, then uncouple the fieldbus!

Before opening the housing of the PC, and whenever the PC is being used
for purposes other than plant control, such as during functional tests
following repair, all parts of the equipment must first be switched off, after
which the Industrial PC can be uncoupled from the plant.

Pulling out the fieldbus connection plug uncouples the PC (optional).

Items of equipment that have been switched off must be secured against
being switched on again.

The Industrial PC’s power supply unit must be supplied with 24 VDC.

Do not exchange any parts when under power!

When components are being fitted or removed, the supply voltage must be
switched off.

Fitting work on the Industrial PC can result in damage:

• If metal objects such as screws or tools fall onto operating circuit
boards.

• If connecting cables internal to the PC are removed or inserted
during operation.

• If plug-in cards are removed or inserted when the PC is switched
on.

4 CP71xx

General Notes

Operator's obligation to exercise diligence

National regulations
depending on the machine
type

Warning

Procedure in the event of a
fault

The operator must ensure that

• the Industrial PC is only used for its intended use (see also

Product Description chapter).

• the Industrial PC is in a sound condition and in working order
during operation.

• the operation manual is in good condition and complete, and
always available for reference at the location of the Industrial PC.

• the Industrial PC is operated, maintained and repaired only by
sufficiently qualified and authorized personnel.

• the personnel is instructed regularly about relevant occupational
safety and environmental protection aspects, and is familiar with
the operating manual and in particular the safety notes contained
herein.

• none of the safety and warning notes attached to the Industrial PC
are removed, and that all notes remain legible.

Depending on the type of machine and plant in which the Industrial PC is
being used, there will be national regulations for the control of such
machines and plant that the operator must observe. These regulations
cover, amongst other things, the intervals between inspections of the
controller.

The operator must initiate such inspections in good time.

Only trained persons may open the Industrial PC housing!

The operator is responsible for ensuring that only trained electrical staff
opens the housing of the Industrial PC.

In the event of a fault in the Industrial PC, appropriate measures can be
determined with the aid of the list in the Fault correction section.

Operator requirements

Read the operating
instructions

Software knowledge

Every user of the Industrial PC must have read these operating
instructions.

Every user must be familiar with any of the functions of the software
installed on the PC that he can reach.

CP71xx 5