Becker INDIANAPOLIS 7925, INDIANAPOLIS 7920, INDIANAPOLIS 7922, INDIANAPOLIS 7923 User Manual
Navigation CD 2.X
Navigation mode
If you received this operation guide update when purchasing a new unit, the
functions and modifications described
from Page 11 are intended as a supplement to your operation guide.
If you received this operation guide update together with an update CD, the update procedure and the new functions
and modifications to the previous mode
of operation are described on the following pages.
Installation update CD 2.X
X Remove the old navigation CD.
X Insert the new 2.X navigation CD.
After a short time, the following display
or a similar display appears.
X Then turn the right rotary control to
select
NEW VERSION: UPDATE.
X Press the right-hand rotary control .
Notes:
• Select
• Press the left rotary control to dis-
OLD VERSION: BACK to
abort the update.
play information on the new version.
The navigation and radio software is
now updated.
Progress bars appear on the display
while the update is taking place.
Note:
While the navigation and radio software is being updated the
• vehicle ignition should be switched on.
• vehicle must not be moved.
After the radio software has been updated the software will be restarted (reset).
The navigation software update then
starts. The update has been completed
when navigation mode can be selected
again.
Subject to errors and technical changes 10 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Navigation CD 2.X
Modifications to navigation
mode
The following modifications have been
made to navigation mode or the following new functions have been added.
• Navigation CDs
• Displaying/changing settings during
route guidance
Navigation CDs
You will be supplied with four navigation CDs.
These CDs contain a digitised road map.
• CD 1 contains the data covering:
Denmark, Great Britain, Finland, Ireland, Norway and Sweden.
• CD 2 contains the data covering:
Austria, Belgium, Denmark, Germany, Liechtenstein, Luxembourg, the
Netherlands and Switzerland.
• CD 3 contains the data covering:
Andorra, Belgium, France, Luxembourg, Portugal and Spain.
• CD 4 contains the data covering:
Austria, the Czech Republic, Italy,
Liechtenstein, Monaco, San Marino,
Slovakia, Switzerland and the Vatican
City.
In addition to the countries listed above,
all the CDs also contain the complete
trunk road network of the digitised area
of Europe.
Motorways, federal and regional roads,
as well as district roads are stored for the
countries included on the individual
CDs. Larger cities and communities are
comprehensively covered. For smaller
towns and communities, the regional
and unclassified roads or access roads
and the town centres are included.
One-way streets, pedestrian zones, turn
bans and other traffic regulations are
taken into account as far as possible.
Note:
There may be discrepancies between
the data on the navigation CD and the
actual local situation, due to continual
changes to road systems and their traffic regulations.
Subject to errors and technical changes 11 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Navigation CD 2.X
Note:
For Norway, Sweden, Finland, the
Czech Republic and Denmark, Nonverified data has been used to achieve
a high depth of digitisation; i.e. with
this data, the navigation system cannot
refer to information such as motorway,
trunk road, 30 zone, one-way street or
other traffic regulations, as this is not
recorded.
All roads can be used, but optimum
route guidance cannot be guaranteed.
Navigation with four European
CDs
1
5
6
7
2
Area covered by CD
1
1.
2 Area covered by CD
2.
3 Area covered by CD
3.
4 Area covered by CD
4.
5 Overlapping area
covered by CD 1
and CD 2.
6 Overlapping area
covered by CD 2
and CD 3.
7 Overlapping area
covered by CD 2
and CD 4.
4
3
Subject to errors and technical changes 12 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Navigation CD 2.X
For example, if you want navigation
guidance from a town which is only covered by CD 2 (CD 2 has been inserted) to
a town which is only covered by CD 3
enter the destination as follows. Select
the country of destination. Then enter
the town required. You can now select
the town centre and start route guidance.
You will then be guided to the centre of
the town required. As soon as you have
left the last trunk road before your destination,
OFFROAD and a direction arrow
will be displayed. In this case, the direction arrow indicates the linear direction
to the selected town centre.
If you would like to be directed to a particular road at the destination you can, as
soon as you are on a trunk road (or in the
area completely covered by CD 3), insert CD 3, enter the exact address of the
destination and begin guidance to this
road.
Notes:
• If you know your way around the
town you are starting out from well
you could insert CD 3 from the beginning and enter the exact destination
address. The system will then show
OFFROAD and a direction arrow until
you reach a trunk road. In this case,
the direction arrow always indicates
the linear direction to the nearest
trunk road.
To prevent
OFFROAD being display-
ed, you can insert CD 2 after the route
has been calculated. Guidance then
takes place in the usual way.
• When the different CDs are changed
you will be shown the message
CHANGE MAP DATA?. Confirm this
message by pressing the right rotary
control . A progress indicator is
displayed while the map data is being
loaded. You can enter the required
destination once the progress indicator has disappeared.
Displaying/changing settings
during route guidance
X During route guidance, press the left
rotary control .
X Press the multifunction button.
The current settings are displayed in a list.
You can display or change the following
settings:
• ROUTE:
Stipulations on the method of route
calculation.
• ETA:
Method of calculating the estimated
time of arrival.
Subject to errors and technical changes 13 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Navigation CD 2.X
• DURATION:
Setting as to whether ETA, the current
time or the remaining travel time
should be displayed on the right side
of the display during navigation.
•
MOTORWAY:
Stipulation as to whether the route is
calculated with or without motorways.
•
FERRY:
Stipulation as to whether the route is
calculated with or without ferries.
• TOLL:
Stipulation as to whether the route is
calculated with or without toll roads.
•
SPEEDLIMITS:
Setting to stipulate whether speed limits are to be displayed during navigation.
X Scroll through the list of settings by
turning the right rotary control .
X To change a setting select the required
entry and press the right rotary
control .
After 8 seconds without operation, or if
the button is pressed, the system
returns to the route guidance display.
The changes are then active.
Note:
After changing some settings (
, MOTORWAY:, FERRY: and
TE:
TOLL:) Indianapolis has to recalculate
ROU-
the route. You may then have to insert
the navigation CD.
Changing ROUTE:
X Select ROUTE: in the settings and
press the right-hand rotary control .
X Then turn the right rotary control
to select the required route calculation
method.
X The setting is accepted by pressing the
right rotary control .
The list of settings is displayed again.
Note:
Further information on the setting options can be found under “Selecting route
settings” in the full operating guide.
Subject to errors and technical changes 14 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Navigation CD 2.X
Changing ETA:
X Select ETA: in the settings and press
the right-hand rotary control .
X Then turn the right rotary control
to select the required setting.
X The setting is accepted by pressing the
right rotary control .
The list of settings is displayed again.
Note:
Further information on the setting options can be found under “Influencing the
calculation of ETA” in the full operating guide.
Changing
X Select DURATION: in the settings
DURATION:
and press the right-hand rotary
control .
X Then turn the right rotary control
to select the required setting.
X The setting is accepted by pressing the
right rotary control .
The list of settings is displayed again.
Note:
Further information on the setting options can be found under “Setting the time
display” in the full operating guide.
Changing
TOLL
X Select MOTORWAY:, FERRY: or
TOLL: in the settings and press the
MOTORWAY:, FERRY: or
right-hand rotary control .
Setting
FERRY: is shown here as an ex-
ample.
X By turning the right rotary control ,
select either
X The selection is accepted by pressing
WITH or WITHOUT.
and holding the right rotary
control .
The list of settings is displayed again.
Note:
Further information on the setting options can be found under “Selecting route
settings” in the full operating guide.
Subject to errors and technical changes 15 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Navigation CD 2.X
Changing SPEEDLIMITS:
X Select SPEEDLIMITS: in the set-
tings and press the right-hand rotary
control .
X By turning the right rotary control ,
select either
X The selection is accepted by pressing
ON or OFF.
and holding the right rotary
control .
The list of settings is displayed again.
Note:
Further information on the setting options can be found under “Switching the
speed limits display on/off” in the full
operating guide.
Modifications to the user settings
The following modifications have been
made to the user settings
Display brightness (Lum)
With this function, the brightness of the
display can be set.
X To set, call up the user menu.
X Press the multifunction button.
X Use the right-hand rotary control
to select between
The setting is stored automatically.
0 (dark) or 8 (light).
Addition to MP3 mode
Audio playback via an optional
Apple™ iPod
Notes:
• The iPod™, the iPod mini™ and the
iPod photo™ are portable MP3 players from Apple, with a hard disk as
a storage medium.
• Apple, the Apple logo and iPod are
Apple Computer, Inc. trademarks, registered in the USA and in other
countries.
Instead of a CD player you can connect
an Apple iPod MP3 player to the
Indianapolis and operate it via the
Indianapolis.
The following Apple iPod series devices
are supported:
• iPod 3rd generation
• iPod 4th generation
• iPod mini
• iPod photo
Subject to errors and technical changes 16 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
To connect an iPod™ to the Indianapolis
you will need the Becker Remote-Kit,
which is available as an optional extra.
The Becker Remote-Kit comes with
connection and operating instructions.
More information can be found under
www.becker.de.
Note:
If the connecting cable is attached to the
Indianapolis, it is not possible to attach
a CD changer or a steering wheel remote control adapter.
Navigation CD 2.X
Subject to errors and technical changes 17 Copyright by HARMAN/BECKER Automotive Systems GmbH, D-76303 Karlsbad
Loading...