Page 1
Ref. No.: 150.525
MHL-363 SPOT 36X3W RGBW
16CH DMX
MANUAL
Page 2
1. Safety Instruction
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked
Disconnect main power before replacement or servicing.
Make sure there is no flammable materials close to the unit while operating as it is fire hazard.
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only,But always by
taking its base.
Maximum ambient temperature is ta:40Ԩ. Don't operate it where the temperature is higher than
this.
Unit surface temperature may reach up to 85Ԩ.Don’t touch the housing bare-hand during its
operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
In the event of serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center. Always use the same type
Spare parts.
Warning
● To prevent or reduce the risk of electrical shock or fire, do not expose the unit the rain or moisture.
● Do not open the unit within five minutes after switching off.
● The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs
youself.In the unlikely event your unit may require service, Please contact your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping white operating. And make sure that the structure to which you are
attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always
use a safety cable hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people and has no one pass by or under it.
Please read the instructions carefully, which includes important
information about the installation, usa
g
e and maintenance
Page 3
2 Technical Specification
Extremely small, fast and powerful LED Moving beam.
DMX Channels:9/12/16CH
Pan/Tilt:630
0
/240
0,
speed adjustable
Smooth electronic dimming:0-100%
Electronic strobe with pulse and random effects
High efficiency, low power consumption
Super compact, low weight
Weight: 5.7kg
Voltage: 90V-240V,50/60Hz
Fuse: T6.3A
Power consumption: 150W
Light source: 3W LED x 36 (R8,G10,B10,W8)
Dimension: 304x267x167mm
Photometric Diagram:
Page 4
3.
H
3.1
C
Display
To sho
w
LED
Button
Mains I
n
Connec
t
Mains
O
Connec
t
DMX In
p
For DM
X
ow To Set
ontrol Pa
n
the various
DMX
MASTE
R
SLAVE
SOUN
D
MENU
DOWN
UP
ENTER
put
to power s
u
utput
to supply p
o
ut / Outpu
t
512 link,us
e
The Unit
el
menus and
pply.
wer to the
n
3/5-pin XL
R
the selected
On
On
On
Flashing
To select t
h
To go back
w
To go forw
a
To confirm
t
ext unit
cable to li
n
functions
D
MMaSla
So
e program
m
ard in the
s
rd in the sel
he selected
k the unit to
X input Pre
s
ster Mode
ve Mode
und activati
o
ing function
s
elected fun
c
ected functi
o
functions
g
ether.
ent
n
tions
ns
Page 5
3.2 Main Function
To select any of the given functions, Press the MENU button up to when the required one is showing
on the display. Select the function by ENTER button and the display will blink. Use DOWN and UP
button to change the mode. Once the required mode has been selected, press the ENTER button to
setup, to go back to the functions without any change press the MENU button again. Hold and press
the MENU button about one second or wait for one minute to exit the menu mode.
The main functions are showing below:
Page 6
DMX Address
Select DMX Address, Press the ENTER button to confirm, the present address will blink on the
display. Use the UP and DOWN button to adjust the address from 1 to 512.Once the address has
been selected, press the ENTER button to setup, to go back to the functions without any change press
the MENU button again. Hold and press the MENU button about one second or wait for one minute to
exit the menu mode
Channel Set
Select Channel Set, Press the ENTER button to confirm, the present set will blink on the display. Use
the UP and DOWN button to select channel 9/12/16.Once the set has been selected,press the ENTER
button to setup, to go back to the functions without any change press the MENU button again. Hold
and press the MENU button about one second or wait for one minute to exit the menu mode.
Show Mode
Select Show Mode, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Show 1 or Show 2 or Show 3 or Show 4 mode. Once the
mode has been selected, press the ENTER button to setup, to go back to the functions without any
change press the MENU button again. Hold and press the MENU button about one second or wait for
one minute to exit the menu mode.
Slave Mode
Select Slave Mode, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Slave 1(normal) or Slave 2 (2 light show)mode. Once the
mode has been selected, press the ENTER button to setup, to go back to the functions without any
change press the MENU button again. Hold and press the MENU button about one second or wait for
one minute to exit the menu mode.
Black Out
Select Slave Mode, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Yes(yes blackout) or No (no blackout)mode. Once the mode
has been selected, press the ENTER button to setup, to go back to the functions without any change
press the MENU button again. Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
Sound State
Select Sound State, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the On(Sound On) or Off (Sound Off)mode. Once the mode has
been selected, press the ENTER button to setup, to go back to the functions without any change press
the MENU button again. Hold and press the MENU button about one second or wait for one minute to
exit the menu mode.
Sound Sense
Select Sound Sense, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the 0…100 mode. Once the mode has been selected, press the
ENTER button to setup, to go back to the functions without any change press the MENU button again.
Hold and press the MENU button about one second or wait for one minute to exit the menu mode.
Pan Inverse
Select Pan Inverse, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Yes(Pan Inversion) or No((Normal)mode. Once the mode has
been selected, press the ENTER button to setup, to go back to the functions without any change press
the MENU button again. Hold and press the MENU button about one second or wait for one minute to
exit the menu mode.
Tilt Inverse
Select Tilt Inverse, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the Yes(Tilt Inversion) or No((Normal)mode. Once the mode has
been selected, press the ENTER button to setup, to go back to the functions without any change press
the MENU button again. Hold and press the MENU button about one second or wait for one minute to
exit the menu mode.
Page 7
Back Light
Select Back Light, Press the ENTER button to confirm, present mode will blink on the display. Use
the DOWN and UP button to select the On(LED On) or Off((LED Off)mode. Once the mode has been
selected, press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit
the menu mode.
Function Delay
Select Function Delay, press ENTER button to confirm, present mode will blink on the display. Use
DOWN and UP button to select the No Delay or 1S/2S/3S Delay (Wait for 1/2/3 seconds before these
Functions of 12CH are activated/deactivated) mode. Once the mode has been selected, press the
ENTER button to setup, to go back to the functions without any 9-change press the MENU button
again. Hold and press the MENU button about one second or wait for one minute to exit the menu
mode.
White Balance
Select White Balance, press the ENTER button to confirm, present mode will blink on the display.Use
the DOWN and UP button to select the Red or Green or Blue. Once the mode has been selected,
press the ENTER button to setup, use the DOWN and UP button to change the value (125~255).
Once the mode has been selected, press the ENTER button to setup, go back to the functions without
any change press the MENU button again. Hold and press the MENU button about one second or wait
for one minute to exit the menu mode.
Manu Test
Select Manu Test, press the ENTER button to confirm, present mode will blink on the display. Use the
DOWN and UP button to select the Pan/ Tilt/ Red/ Green/ Blue/ White/Dimmer or Strobe. Once the
mode has been selected, press the ENTER button to setup, use the DOWN and UP button to change
the value (0~255). Once the mode has been selected, press the ENTER button to setup, go back to
the functions without any change press the MENU button again. Hold and press the MENU button
about one second or wait for one minute to exit the menu mode.
Auto-Test
Press the MENU button up to when the Auto-Test is blinking on the display. Pressing ENTER button
and the unit will run self-test by built-in program. To go back to the functions press the MENU button
again. Hold and press the MENU button about one second or wait for one minute to exit the menu
mode.
Temperature
Press the MENU button up to when the Temperature Test is blinking on the display. Pressing ENTER
button and the display will show the temperature of the unit. To go back to the functions press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit
the menu mode.
Defaults Setting
Press the MENU button to show Defaults on the display. Press the ENTER button and the display will
blink. Use the DOWN and UP button to select the YES or No. Once the Yes has been selected, press
the ENTER button and use the UP and Down button to select the PRO Defaults or AUTO Defaults.
PRO Defaults: For professional users, detailed explanation as followings:
Slave Mode -->Slave 1
Black Out -->Yes
Sound State -->Off
Pan Inverse -->No
Tilt Inverse -->No
Back Light -->Off
Function Delay -->3S Delay
Page 8
AUTO Defaults: Mostly automatic mode, for non-professional users, detailed explanation as
followings:
Slave Mode -->Slave 1
Black Out -->No
Sound State -->On
Pan Inverse -->No
Tilt Inverse -->No
Back Light -->On
(Notice: Other settings are NOT changed while choosing Defaults Setting!)
Press the ENTER and the corresponding functions will set to defaults setting, to go back to the
functions without any change press the MENU button again. Hold and press the MENU button about
one second or wait for one minute to exit the menu mode
Reset
Press the MENU button up to when the Reset is blinking on the display. Pressing ENTER button and
all channels of the unit will return to their standard position.
3.3 Home Position Adjust
In the main functions, hold ENTER button for at least 3 seconds into offset mode, use DOWN and UP
button up to choose Pan Offset or Tilt Offset, Pressing ENTER button and the display will blink. Use
DOWN and UP button to adjust the home position of the Pan, Tilt, Once the opposition has been
selected, press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one minute to exit
the menu mode.
4. How to Control the Unit
You can operate the unit in two ways:
1. Master/Slave built-in preprogram function
2. Universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address setting will be
effect at once. Every time you turn the unit on, it will show “M108RGBW”on the display and move all
the motors to their “HOME” position and you may hear some noises for about 20 seconds. After that
the unit will be ready to receive DMX signal or run the built in programs.
4.1 Master/Slave Buit-in pre-programmed Function
By lining the units in master/slave connection, the first unit will control the other units to give an
automatic, sound activated, synchronized light show. This function is good when you want an instant
show. You have to set the first unit in master mode Show Mode and select Show 1 or Show 2 or
Show 3 or Show 4 mode. Its DMX input jack will have nothing plugged into it, and its master LED will
be constantly on and sound LED will flash to the music. The other units will have to set in Slave mode
and select Slave 1(normal) or Slave 2(2 light show)mode, Their DMX cables plugged into the DMX
input jacks(daisy chain) and the slave led lights will constantly on.
2-light show
In Slave mode, Slave 1 means the unit works normally and Slave 2 means 2-light show. In order to
create a great light show, you can set Slave 2 on the second unit to get contrast movement to each
other, even if you have two units only.
Page 9
4.3 DMX Controller
By using a universal DMX Controller to control the units, you will need to set DMX address from 1 to
512 so that the units can receive DMX signal
Press the MENU button up to when the DMX Address is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once
the address has been selected, press the ENTER button to setup, to go back to the functions without
any change press the MENU button again. Hold and press the MENU button about one second or wait
for one minute to exit the menu mode.
4.4 DMX 512 Configuration
9 Channel Mode:
Channel List Value Function
CH1 000-255 Pan(0-630)
CH2 000-255 Tilt(0-240)
CH3 000-255 Strobe
CH4 000-255 Red (0%-100%)
CH5 000-255 Green (0%-100%)
CH6 000-255 Blue (0%-100%)
CH7 000-255 White (0%-100%)
CH8 000-255 Dimmer (0%-100%)
CH9 000-255 Sound active
12 Channel Mode:
Channel List Value Function
CH1 000-255 Strobe Effect
CH2 000-255 Dimmer (0%-100%)
CH3 000-255 Pan(0-630)
CH4 000-255 Pan Fine(Least significant bit)
CH5 000-255 Tilt (0-240)
CH6 000-255 Tilt Fine(Least significant bit)
CH7 000-255 Sound activation
CH8 000-255 Color Effect
CH9 000-255 Red (0%-100%)
CH10 000-255 Green (0%-100%)
CH11 000-255 Blue (0%-100%)
CH12 000-255 White (0%-100%)
16 Channel Mode:
Channel List Value Function
CH1 000-255 Pan(0-630)
CH2 000-255 Pan Fine(Least significant bit)
CH3 000-255 Tilt (0-240)
CH4 000-255 Tilt Fine(Least significant bit)
CH5 000-255 Pan & Tilt Speed
CH6 000-255 Pan & Tilt Auto Run
CH7 000-255 Auto Run Speed
CH8 000-255 Auto Run Color Open
CH9 000-255 Dimmer (0%-100%)
CH10 000-255 Strobe
CH11 000-255 Red (0%-100%)
CH12 000-255 Green (0%-100%)
CH13 000-255 Blue (0%-100%)
CH14 000-255 White (0%-100%)
CH15 000-255 Color Auto Run
CH16 000-255 Color Auto Run Speed
Page 10
4.5 DMX 512 Connection
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor
between pin 2(DMX-)and pin 3(DMX+)into a 3-pin XLR-plug and plug it in the DMX-output of the
last unit
3. Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of
the next unit. The cable cannot branched or split to a ‘Y’cable.DMX512 is a very high-speed
signal. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort
the signal and shut down the systems.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when one of
the units power is disconnected.
5. Each lighting unit needs to have an address set to receive the data sent by the controller. The
address number is between 0-511(usually 0 & 1 are equal to 1.)
6. The end of the DMX512 system should be terminated to reduce signal errors
7. 3 pin XLR connector are more popular than 5 pin XLR
3 pin XLR: Pin 1:GND,Pin 2:Negative signal(-),Pin 3:Positive signal(+)
5 pin XLR: Pin 1:GND,Pin 2:Negative signal(-),Pin 3:Positive signal(+),
Pin 4/ Pin 5:Not used
SPECIFICATION
Power 108W
Head movement:Pan 630°
Head movement:Tilt 240°
Beam angle 5°
No. of LEDs 36x 3W (8x Red, 10x Green, 10x Blue & 8x White)
DMX channels 9,12 or 16
Connector 3-pin XLR
Power Supply 90~240Vac / 50Hz
Consumption 150W
Dimensions 304 x 267 x 167mm
Weight 5.7kg
Page 11
CE Declaration of Conformity
Importer: TRONIOS BV
Bedrijvenpark Twente 415
7602 KM - ALMELO
Tel : 0031546589299
Fax : 0031546589298
The Netherlands
Product number: 150.525
Product Description: Beamz Professional,
MHL-363 Spot 36x3W RGBW 16ch
DMX
Regulatory Requirement: EN 60598-1
EN 60598-2-17
EN 61000-3-2/-3-3
EN 55015
EN 61547
The product meets the requirements stated in the above mentioned Declaration(s).
ALMELO,
28-06-2013
Signature :
Page 12
Specificationsanddesignaresubjecttochangewithoutpriornotice..
www.tronios.com
Copyright©2013byTRONIOStheNetherlands
Loading...