Beam Electrolux Serenity Plus Power Brush User Manual
# 460337 3/06
IMPORTANT SAFETY INSTRUCTIONS
Your Powerbrush combines power cleaning with ease of maintenance and represents the very best
in design and manufacturing. However, as with any powerful appliance, caution must be exercised
while using this Powerbrush. You will find the safety precautions and maintenance instructions
outlined in this manual useful. When using an electrical appliance, the following basic precautions
should always be followed:
READ ALL INSTRUCTIONS BEFORE
USING THIS POWERBRUSH.
WARNING:
or damage to the product, the following precautions should be followed.
1. Keep loose clothing, hair, fingers, and other parts of the body away from openings and moving
parts (brush roller) when the Powerbrush is connected to an electrical outlet.
2. Turn off all controls before unplugging.
3. Disconnect the Powerbrush from the electrical outlet prior to any servicing.
4. Do not handle the Powerbrush, its electrical cord, or plug with wet hands.
5. Do not use with damaged cord or plug. If the appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center for
servicing/repair.
6. Do not use the Powerbrush in areas where flammable or combustible liquids, such as gasoline, are
present.
7. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
8. Electric shock could occur if the Powerbrush is used outdoors or on wet surfaces.
9. Always turn off the Powerbrush before connecting and disconnecting the hose.
10. If a current carrying hose is used in conjunction with the Powerbrush, ensure the hose is not damaged, cut, or punctured. Avoid picking up sharp objects.
11. Do not pull or carry by the cord, use the cord as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Keep the cord away from heated surfaces. Do not run the appliance over the cord.
12. Do not attempt to pick up anything that is burning or smoking, such as cigarettes, matches, or hot
ashes with the Powerbrush.
13. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce air flow.
14. Use extra care when cleaning on stairs.
15. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
16. Do not leave the appliance unattended when plugged in. Unplug from outlet when not in use.
17. Use only as described in this manual. Use only manufacturer’s recommended attachments.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the
18.
other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.
To reduce the risk of fire, electric shock, possible personal injury,
SAVE THESE INSTRUCTIONS
1
Re-Set Button
(circuit breaker)
C) Indicater Lights
F) 4 Soft Rubber Wheels
E) W
rap-A-round Bumper
D) Florescent Headlight
B) Neck Release Pedal
A) Locking Pivot/Swivel Neck
Wand Socket
Figure 2
OPERATING INSTRUCTIONS
Press reset button
4
Figure 4a
When using the Powerbrush, the basic precautions outlined under
“IMPORTANT SAFETY INSTRUCTIONS” should always be followed.
1. Make sure the hose handle switch is in the OFF position.
2. Insert hose end into the Powerbrush wands on the assembled Powerbrush.
For proper connection, ensure the spring button lock pops out (Figure 4a).
3. Insert the hose into a wall vacuum valve (faceplate), and plug the cord into
electrical outlet (as shown in Figure 4b).
4. You may secure the Powerbrush by depressing neck release pedal with
your foot on top if the hood. Lower the wands from the upright position.
Switch hose to the ON position.
5. The red warning lamp will light if the brush rotation is restricted. This can
occur if an object causes brush speed reduction, thus overloading the drive
motor. If this occurs:
•
Turn off vacuum cleaner and disconnect the power supply cord
•
Remove obstruction
•
Reconnect to power supply
•
Figure 4a
Helpful Hint:
hard or sharp objects. Articles of clothing, towels, loose carpet edges, etc.
should also be avoided. If an article does become entangled in the brush roller,
switch off the Powerbrush. Disconnect the hose cord from electrical outlet and
the hose from the faceplate and then remove the object carefully without using
excessive force.
To prevent possible damage to the powerbrush, do not pick up
Figure 4b
4
Loading...