Beam Electrolux Alliance Solaire User Manual [en, es, fr]
BEAM Alliance Solaire
Cleaning Set Manual
IMPORTANT SAFETY INSTRUCTIONS
Your Powerbrush combines power cleaning with ease of maintenance and represents the very
best design and manufacturing. However, as with any powerful appliance, caution must be
exercised while using this Powerbrush. You will nd the safety precautions and maintenance
instructions outlined in this manual useful. When using an electrical appliance, the following
basic precautions should always be followed:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM SYSTEM.
WARNING
To reduce the risk of re, electric shock or injury:
• Keep loose clothing, hair, ngers and other parts of the body away from openings and moving
parts (brush roller) when the Powerbrush is connected to an electrical outlet.
• Turn off all controls before unplugging.
• Disconnect the Powerbrush from the electrical outlet prior to any servicing.
• Do not handle the Powerbrush, its electrical cord or plug with wet hands.
• Do not use with damaged cord or plug. If the appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center
for servicing/repair.
• Do not use the Powerbrush in areas where ammable or combustible liquids, such as gasoline,
are present.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Electric shock could occur if the Powerbrush is used outdoors or on wet surfaces.
• Always turn off the Powerbrush before connecting and disconnecting the hose.
• The hose contains electrical wires. Do not use when damaged, cut or punctured.
• Do not pull or carry by the cord, use the cord as a handle, close a door on the cord or pull the
cord around sharp edges or corners. Keep the cord away from heated surfaces. Do not run the
appliance over the cord.
• Do not attempt to pick up anything that is burning or smoking, such as cigarettes, matches, or
hot ashes with the Powerbrush.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce air ow.
• Use extra care when cleaning on stairs.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not leave the appliance unattended when plugged in. Unplug from the outlet when not in use.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than
the other). This plug will t in a polarized outlet only one way. If the plug does not t fully in the
outlet, reverse the plug. If it still does not t, contact a qualied electrician to install the proper
outlet. Do not change the plug in any way.
2
Congratulations on your purchase of the BEAM Alliance Central Vacuum System, the ultimate
cleaning solution. The BEAM Alliance Central Vacuum System is designed to help you efficiently
clean and maintain your home. While vacuuming may never be truly pleasurable, you can have a
cleaner, healthier home. . . and more time to do the things you really enjoy.
Your BEAM Alliance Solaire Cleaning Set has been designed to work only with the BEAM
Alliance Central Vacuum System. Any use with another central vacuum system may cause
damage to the system components and void the warranty.
To achieve the maximum benets from your BEAM Alliance Solaire Cleaning Set, please
read this manual carefully.
For more information regarding BEAM and other innovative products from BEAM,
visit www.beam.com.
TELESCOPIC WAND FEATURES
• Variable speed control
• Handle release button
• Telescopic wand slide adjustment
• Depress foot pedal to release wand
Figure 1.
3
POWERBRUSH FEATURES
1. Cogged Belt – The cogged belt is designed for positive drive, and it will not stretch or slip.
The long life of the sturdy cogged belt also reduces the need for frequent replacement to
enhance cleaning efficiently.
2. LED Lamp – The super bright light of the LED (Light
Emitting Diode) lamp allows for better vision in poorly lit
areas for more thorough cleaning. It is also much more
durable than incandescent or halogen bulbs.
3. Automatic Carpet Height Adjustment – The Powerbrush
is equipped with two small roller wheels at the front which
keep the Powerbrush at the correct distance from the
carpet for optimal cleaning.
4. Circuit Breaker – The electronic circuit breaker protects the
motor and the cogged belt from damage should a motor
stall occur due to accidental pick up of a larger object.
The LED light located on the back of the powerbrush (see
Figure 2.) will glow green in color for normal operation and
ashing red in color for a stalled or jammed condition.
Figure 2
CAUTION! TO REDUCE THE RISK OF INJURY, BRUSHROLL COULD SUDDENLY
RESTART, UNPLUG BEFORE SERVICING.
When brushroll jam has been cleared, circuit breaker can be reset by switching hose handle
switch “off” then “on”. Your Powerbrush must be serviced by an authorized service center if it
continues to trip the circuit breaker.
5. Isolated Brush Compartment – The electrical compartment is totally separated from the
sweeping area. This providesuser safety and shields the electric motor from dust and dirt to
enhance motor life.
6. Dual Ball Bearing Brush Roller – The
rotating brush mechanism utilizes
precision ball bearings for extra smooth
running and durability.
7. Chevron Brushroll – Pulls dirt to main
airchannel.
8. Wheel Bearings - The rear wheels are
equipped with sealed ball bearings
providing a quiet long lasting assembly.
Powerbrush Wiring Diagram
4
ASSEMBLY & OPERATING INSTRUCTIONS FOR THE POWERBRUSH
Status OK
Power Nozzle Button
(2G)
Status OK
Power Nozzle Button
(2G)
(2G)
(2G)
When using the powerbrush, the basic precautions outlined under “IMPORTANT SAFETY
INSTRUCTIONS” should always be followed.
1. Push the wand into the powerbrush socket until it locks in place. The wand
socket is designed with a positive stop. Therefore, the wand will not jam in the
wand socket. Insert hose end into the powerbrush wand on the assembled
powerbrush until is locks in place. (gure 3)
2. Make sure the hose handle button is OFF. Note: The handle is in the OFF
position when the indicator in the ( ) button is OFF.
3. Insert the hose into the wall inlet valve (faceplate), and plug the cord into the
electrical outlet. (gure 4)
4. Lower the wand from the upright position.
Figure 3.
5. To turn the central vacuum ON, press the ( ) button.
6. To turn on the powerbrush, press the powerbrush button ( ) to
turn it on.
7. To turn off the powerbrush, press the symbol Powerbrush ( )
button. The indicator in the icon will turn off.
8. Disconnect the handle from the wand by pushing the button on the
wand that is closest to the handle, and pulling the handle out of the
Figure 4.
wand socket.
9. Variable speed allows you to vary the suction power. Press ( + / - )indicator button. An
indicator in the handle will show bars and the different speed levels.
10. Release the wand from the powerhead by depressing the foot pedal and pulling the wand out
of the powerbrush socket.
Helpful Hint: To prevent possible damage to the Powerbrush, do not pick up hard or sharp
objects. Articles of clothing, towels, loose carpet edges, etc., should also be avoided. If an article
does become entangled in the brush roller, switch off the Powerbrush. Disconnect the hose
cord from electrical outlet and the hose from the faceplate and then remove the object carefully
without using excessive force.
WARNING: Always switch off the Powerbrush and disconnect plug from wall electrical
outlet and disconnect hose before servicing the Powerbrush.
GENERAL CLEANING
1. The Powerbrush can be wiped with a cloth dampened with warm water and a mild detergent.
2. Do not use abrasive substances or any solvents.
5
3. Do not immerse in water or allow water to enter the Powerbrush.
BRUSH ROLLER CLEANING
For top cleaning performance, it is recommended that the brush roller and the brush roller
compartment be cleaned on an occasional basis.
WARNING: Always switch off the Powerhead and disconnect plug from wall outlet and
disconnect hose before servicing the Powerbrush.
1. Turn the Powerbrush upside down.
2. Press the 3 snap release clips (as shown in Figure 5)
and remove brush cover.
3. The brush roller is now exposed for removal of bers,
hair, etc. from the bristles and around the brush roller.
4. To remove bers or hair entangled around the brush
roller, cut parallel to brush roller.
Figure 5.
5. You may further clean the brush compartment with your
central vacuum system.
6. Replace the brush cover by inserting the tabs on
the front of the cover into the appropriate slots in the
Powerbrush base (as shown in Figure 6) and press
down on the three clips until they snap-lock into place.
Figure 6
POWERBRUSH MAINTENANCE
How to Change Cogged Belt.
WARNING: Always switch off the Powerbrush and disconnect plug from wall electrical outlet
and disconnect the hose before servicing the Powerbrush.
1. Remove the brush cover as described in “Brush Roller Cleaning” steps 1 and 2.
2. Insert a string around the brush roller close to the
cogged belt. Pull both ends of the string upwards so
that the brush roller disengages from the base (as
shown in Figure 7. Similarly, disengage the other end.
3. Remove and clean the bearing shaft from the
brush roller ends. Notice the bearing shafts are not
symmetrical. The slanted one belongs to the Brush gear
(cogged belt side, as shown in Figure 8).
6
Figure 7.
4. Remove the old belt. (You may also cut the old belt with
scissors to quickly remove it).
5. Slip the new cogged belt over the gear on the motor shaft
(as shown in Figure 9).
6. Now slip the belt onto the brush gear of the brush roller.
7. Slide the bearing housing in the corresponding slots on
the base. Make sure both are completely pushed into
place; the tab on the slanted bearing housing must t into
the slot at the bottom of the brush compartment.
8. Replace the Brush cover as described in item 6 under
Brush Roller Cleaning.
Figure 8.
Figure 9
7
Lifetime Limited Warranty
Electrolux Central Vacuum Systems is protected by a limited lifetime warranty. This warranty is valid from
the date of purchase, for as long as you are the original owner, and the system remains at its original
place of installation.
• Limited lifetime warranty on metal body and self cleaning lter.
• Motors, electrical components and dirt receptacle in BEAM Alliance power units are warranted for 15
years.
• BEAM Alliance cleaning sets carry a 5 year warranty.
• Labor on all warranted items is covered for 1 year.
This warranty does not apply to consumable items requiring normal replacement such as belts,
replacement lter bags and lights.
THIS IS THE SOLE AND EXCLUSIVE WARRANTY OF ELECTROLUX CENTRAL VACUUM SYSTEMS.
IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION OF LIMITED WARRANTY PERIOD.
Should any defect in material or workmanship appear within the time of the above warranty, the selling
BEAM Dealer should be contacted. The Dealer shall repair or replace (at BEAM’s sole option), or credit,
such part or parts in accordance with the applicable warranty period stated above. BEAM shall not be
responsible for such service unless provided by an authorized BEAM Dealer utilizing authentic BEAM
replacement parts.
This warranty does not apply to loss or damage resulting from (at BEAM’s sole option) normal wear and
tear, commercial use, vacuum of drywall dust, neglect, abuse acts of God, accidents, improper installation,
improper modication or alteration, improper use and operation or failure to provide proper maintenance.
Some States or Provinces do not allow exclusion of warranties or limitations of damages, so the above
limitations and exclusions may not apply to you. This warranty gives you specic legal rights. You may have
additional rights, which vary from State to State, or Province to Province. This limited warranty applies
to USA and Canada installations only. For specic warranty information for your Country, consult your
authorized Beam Dealer.
Other warranties apply to other parts of this equipment and optional accessories. Please contact the
material accompanying the individual items.
BEAM SHALL NOT BE RESPONIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR SPECIAL
DAMAGES ARISING FROM THE USE OF THIS SYSTEM.
Keep all payment records (bill of sale/delivery slip). The date on these records establishes the warranty
period. Should warranty service be required, you must show proof of purchase. If proof of purchase cannot
be supplied, the warranty period will be determined from the date of manufacture of the product.
In the event of a product recall, register your products at www.beam.com.
© 2013 Electrolux Home Care Products Ltd. #87249-R1
8
Loading...