BEA Matrix2-S User Manual

BEA’s digital inductive

single loop

solution

Matrix2-S

With more standard features
than any other loop detector
on the market, the Matrix2-S

has the flexibility, compatibility

and performance to maximize

productivity and safety

on your site.

Try it NOW

The Future of Sensors, Now!

www.beasensors.com

n Matrix2-S is a series of digital inductive, single loop detectors for vehicle access

control and safety for doors, gates, and numerous other applications.
High performance features include :

> PRESENCE time adjustability up to INFINITY
> Selection of PRESENCE and PULSE outputs
> AUTOMATIC SENSITIVITY BOOST increases the sensitivity upon detection, and allows

for continuous detection of high-bed vehicles
> Four frequency settings ensure NO CROSSTALK occurs between adjacent loops
> The microprocessed Matrix adjusts to OUTSIDE TEMPERATURES - detection is not

affected by long-term occupation of the loop

n The Matrix2-S is available in two models to accommodate nearly any application

> Available in single channel mode, and power supply configurations of 110 or 220

volts AC, or 12-24 volts AC/DC, the Matrix is compatible with any door control or
application you may encounter

n Unlike traditional DIP switches, the Matrix2-S’s continuous mode adjustments allow

for precise settings to match your application

> Settings such as sensitivity and presence are adjusted via potentiometer so wide

ranges and precise adjustments are made easy

2

4

1

5

3

6

Technology Inductive loop
Tuning automatic
Detection mode presence
Presence time 1 min to infinity (permanent presence)

with 250 steps.

Pulse time output 100 ms or 500 ms
Inductance range 20 micro to 1000 micro
Frequency range 20 kHz to 130 kHz
Frequency steps 4 for single loop / 2 for dual loop

(for each loop)

Sensitivity (DL/L) 0.005% to 0.5% with 250 steps
Reaction time 25ms for single loop
Setup time at power on 8 seconds maximum by channel
Setup time after configuration 2 seconds maximum by channel
Power supply 12-24 AC/DC ± 10% / 230 VAC

± 10% / 115 VAC ± 10%

(depending on model)

Frequency range 48 to 62 Hz
Power Consumption <2.5W
Temperature range -22°F to +158°F (-30°C to +70°C)
Degree of protection IP40
2 Output relays · Max contact voltage : 230 VAC

(free potential change-over contact)

· Max contact current : 5A (resistive)

LED indicators · 1 green LED : power

· 1 red LED : Loop status 1

· 1 red LED : Loop status 2

Protections · loop insulation transformer / Zener

diodes / gas discharge clamping.

Connection Standard 11-pin round connector

86CP11

Dimensions · Height: 3" (77mm) / Width: 1 5/8"

(40mm) / Depth: 3" (77mm)

Weight < 7 ounces
Immunity electromagnetic compatibility (EMC)

according to 89/336/EEC and its amendments

Matrix Components

1

Main connector (86CP11)

2

Power LED

3

Presence time potentiometer

4

DIP switches

5

Detection state LED

6

Sensitivity adjustment potentiometer

Matrix2-S applicationMatrix2-S Technical Specifications

Gate opening and safety:

The Matrix2-S will activate
and hold open a gate
(parking as shown above)
as soon as a vehicle enters
or stay in its field of detection.

Industrial Door:

The Matrix2-S will activate and
hold open an industrial door as
soon as a vehicle enters or stay in
its field of detection.

Contact Information

BEA Inc.
RIDC Park West
100 Enterprise Drive
Pittsburgh PA, 15275
Phone [phone]
Fax [phone]
Toll Free 1-800.523.2462

BEA West
2401 Pine Street
Los Angeles, CA 91767
Phone [phone]
Fax [phone]
Toll Free 1-877.232.9378

www.beasensors.com