600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 •
600 UL MAGLOCKS
• 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 •
600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 • 600 •
USER’S GUIDE
ELECTROMAGNETIC LOCK
1 Description
The Electromagnetic Lock (Maglock) series is a surface mounted magnetic lock assembly. Available in single and dual lock varieties
and various sizes (force) designed for standard installation on most types of doors.
SINGLE
10MAGLOCK3UL
2 Specifi cations
DESCRIPTION 10MAGLOCK3UL 10MAGLOCK6UL
Lock Single Double
Imput Voltage (VDC) 12 or 24 12 or 24
Relay Rating: @ 24 VDC (amps) 1.0 1.0
Dimensions: inches
(mm)
Certifi cation: UL UL
3 Precautions
Shut off all power before attempting any wiring procedures.
Maintain a clean & safe environment when working in public areas.
Constantly be aware of pedestrian traf c around the door area.
Always stop pedestrian traf c through the doorway when performing tests that may result in unexpected reactions by the door.
Always check placement of all wiring before powering up to insure moving door parts will not catch any wires and cause
damage to equipment.
Ensure compliance with all applicable safety standards and building codes upon completion of installation.
9.84 x 1.65 x 1.02
(250 x 42 x 26)
19.76 x 1.65 x 1.02
DOUBLE
10MAGLOCK6UL
(502 x 42 x 26)
4 Installation - Mechanical
1. Handle the equipment with care. Damaging the mating surfaces of the magnet and armature plate may reduce locking ef ciency.
2. The maglock mounts rigidly to the door frame. The armature plate mount to the door with the hardware provided. This allows the
armature plate to pivot about its center to compensate for door wear and misalignment.
3. Template use must take place with the door in its normally closed position.
4. Add threadlocker to all screws before installing.
5. Firmly tighten screws.
75.5366.00 20080821 Page 1 of 2
C/L
4 Installation - Mechanical (Cont’d)
1 2 3 4 5
+ - NO C NC
+ -
12VDC
24VDC
Switch or solid
state switching
device
Switch or solid
state switching
device
AC
110V
or
220V
AC
110V
or
220V
DC
12V
or
24V
DC
12V
or
24V
+
-
+
-
DOOR FRAME
DOOR
MOUNTING
PLATE
MAGNET
ARMATURE PLATE
DOOR FRAME
STRINGER
MOUNTING
PLATE
DOOR DOOR
MAGNET
ARMATURE PLATE
DOOR FRAME
ANGLE
BRACKET
MOUNTING
PLATE
MAGNET
ARMATURE PLATE
NOTE: DO NOT over-tighten the armature plate. The rubber washer is
designed to allow the armature plate to automatically adjust position
for best mating position between the lock and armature plate.
5 Installation - Electrical
NOTE: The product should only be powered by a UL listed power supply.
NOTE: If power switch is not wired between DC source voltage and magnet,
it will take a longer time to de-energize the magnet simulating residual magnetism.
1. 12 VDC INPUT
A. Required power 0.5A (Max).
B. Connect ground (-) lead from a 12 VDC power source to Terminal 2.
C. Connect positive (+) lead from a 12 VDC power source to Terminal 1.
D. Check jumper for 12 VDC operation.
2. 24 VDC INPUT
A. Required power 0.25A (Max).
B. Connect ground (-) lead from a 24 VDC power source to Terminal 2.
C. Connect positive (+) lead from a 24 VDC power source to Terminal 1.
D. Check jumper for 24 VDC operation.
3. CONTACTS
1. Relay dry contacts are rated 1A at 24 VDC for safe operation, DO NOT exceed this
rating.
2. If a NO switch is required, connect the wires from the system to Terminal 4 & Terminal 3.
3. If a NC switch is required, connect the wires from the system to Terminal 4 & Terminal 5.
NUT
TYPICAL INSTALLATION
SPACER
DOOR
GUIDE PIN
POWER
SUPPLY
+ -
HOLE FOR
GUIDE PIN
HOLE FOR NUT
RUBBER WASHER
STEEL WASHER
ARMATURE PLATE
SCREW M8 (35MM)
NUT
DOOR
ARMATURE
CORRECT
INCORRECT
LOCK STATUS SWITCH (SPDT)
SELECTOR
WASHER
PLATE
POWER
JUMPER
6 Company Contact
Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troubleshooting a problem, please
contact BEA Inc. If you must wait for the following workday to contact BEA, leave the door inoperable until satisfactory
repairs can be made. Never sacrice the safe operation of the automatic door or gate for an incomplete solution.
The following numbers can be called 24/7. For more information, visit www.beasensors.com.
US and Canada:
Page 2 of 2 75.5366.00 20080821
Canada:
Northeast:
1-866-249-7937
1-866-836-1863
1-866-836-1863
Southeast:
Midwest:
West:
LED
MAG BOND SENSOR
MAGNET
TIMER (0-90 SEC)
1-800-407-4545
1-888-308-8843
1-888-419-2564
Loading...