BEA 10BOXJAMBFM, 10T300PB, 10BOXJAMBSM, 10PBJx, 10BOX45RSM User Manual
PRODUCT
COMPONENT ID
SAFETY
JAMB
JAMB
SQUARE
SQUARE
ROUND
ROUND
3 ¼”
USERS GUIDE
9V Battery Clip
on jamb sized boxes)
Transmitter Mounting Pin
(6 per box, not used on jamb
Pushplate Mounting Box
We open up New Horizons
DESCRIPTION
(4 ½” Round Surface Mount shown)
PUSHPLATE MOUNTING BOXES
BEA’s line of pushplate hardware is expanded by its line of surface and flush mount pushplate boxes. These
boxes are made of durable ABS plastic and are made to securely mount a pushplate and a variety of
optional transmitters to activate an automatic door. Many of the boxes have an optional weather ring to give
even more weather protection to the switch. They are also designed to attractively recess the pushplate in
the housing to and to minimize vandalism from prying up the pushplate.
PUSHPLATE SIZE PUSHPLATE
SERIES
Jamb (4” hole spacing) 10PBJx 10BOXJAMBSM 10BOXJAMBFM N/A
Jamb (3 ¼” hole spacing) 10PBJSx 10BOXJAMBST N/A N/A
4 ½” Square 10PBS45x 10BOX45SQSM N/A N/A
4 ¾” Square 10PBSx 10BOX475SQSM 10BOX475SQFM 10WRSQ475
4 ½” Round 10PBR45x 10BOX45RNDSM 10BOX45RNDFM 10WRRND45
6” Round 10PBRx 10BOX6RNDSM 10BOX6RNDFM 10WRRND6
SURFACE MOUNT BOX FLUSH MOUNT BOX WEATHER RING
(1 per box, not used
sized boxes)
(Optional)
PRECAUTIONS
75.0092 V4 Jan 2004 [Rev. 1/26/2004]
4”
4”
3 ¼ ”
4 ½”
4 ¾ ”
4 ½ ”
• Shut off all power going to the header before attempting any wiring procedures.
• Maintain a clean & safe environment when working in public areas.
• Constantly be aware of pedestrian traffic around the door area.
• Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected
reactions by the door.
• Always check placement of all wiring before powering up to insure that moving door parts will not catch
any wires and cause damage to equipment.
• Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of
installation.
6”
Page 1 of 2
COMPANY
MECHANICAL
INSTALLATION
GALVANIZED MOUNTING
‘mini’ transmitters
1. Prepare the box for installation. If the pushplate is to be hard-wired to the operator, remove either the
knockout on the back or bottom of the box. Then route the appropriate wire to the box.
2. Attach the box to the mounting surface. For surface mounted boxes, securely attach the box to the
surface using the corner holes. For flush mounted boxes, cut a hole in the mounting surface large enough
that the galvanized steel bracket will pass through the hole. Then use a Phillips head screwdriver to
tighten the two screws that tighten the bracket to the inside of the wall surface.
BRACKET
CONTACT
3. If applicable, mount a radio frequency transmitter to the inside of the housing using either the transmitter
pins and 9V battery clip, or the Velcro tab enclosed with the transmitter kit.
Transmitter Mounting Pins
(adjust location for transmitter)
or use Velcro tab to secure
9V Battery
10BOX45RSM with 10T300PB shown
SURFACE MOUNT FLUSH MOUNT
If after troubleshooting a problem, a satisfactory solution cannot be achieved, please call B.E.A., Inc.
for further assistance during Eastern Standard Time at 1 -800-523-2462 from 8am - 5pm.
For after-hours, call East Coast: 1-866 -836-1863 or 1-800-407-4545 / Mid-West: 1-888-308-8843 /
West Coast: 1-888 -419-2564. DO NOT leave any problem unresolved. If you mus t wait for the following
workday to call B.E.A., leave the door inoperable until satisfactory repairs can be made.
NEVER sacrifice the safe operation of the automatic door or gate for an incomplete solution.
Web: www.beasensors.com
75.0092 V4 Jan 2004 [Rev. 1/26/2004]
Page 2 of 2
Loading...