BE WHIRL-A-WAY BE-1600WAW, WHIRL-A-WAY BE-2200WAWG, WHIRL-A-WAY BE-1800WAW, WHIRL-A-WAY BE-2000WAWY, WHIRL-A-WAY BE-2000WAWS Operation Manual
...
WHIRL-A-WAY
OPERATIONS MANUAL
BE-1200WAW
BE-1600WAW
BE-1800WAW
BE-2000WAWY
BE-2200WAWG
BE-2000WAWS
BE-2400WAWS
DISTRIBUTED BY
16" - 24" SET-UP PROCEDURES
We re com men d
that you first fit
the l owe r p ortion of the handle
into the mounting
brackets on the
cover and secure
with the bolts or
the pins & clips.
1 2
Next, tighten
the “xed” hose
end into the gun
mounted onto
the upper portion
of the handle.
Use teon tape
on the hose ends
and tighten until
snug. Do not
overtighten.
Once this is complete, join the two
se c tio ns of the
handle together
and secure with
th e bol t or the
pin & clip.
3
Tur n th e co v er
over and check to
ensure tha t the
noz zle ti ps ar e
securely tightened
and the spray pattern is in line with
the rotary arm.
5
4
Next, tighten the
swivel end of the
hose into the top
of the rotary head
until snug.
Inspect the r ota ry
head to make sure
the rotary arm spray
tips are a minimum
of 1” distance from
th e su rf ace be in g
cleaned.
6
1
NOTES
T
he Surface Cleaning System you have purchased
connects directly to your high pressure hose and
pressure washer by means of quick couplers, operating
to a maximum of 4000 PSI. Please note that the 12"
Whirl-A-Way connects directly to a 1/4" quick connect
coupler, operating to a maximum of 2500PSI.
This Whirl-a-Way is designed to operate with both hot &
cold water pressure washers up to 180°F.
We recommend that you supply grease to the rotary head
every 30 – 40 hours of use. Simply add a small squirt of
automotive grease, do not overll with grease as it will
bog down the rotary head.
During operation, should you experience a buildup of
small stones or other foreign material within the cover,
we recommend that you simply tip the cleaner on its side
at 45° which should expel any foreign materials. This
will give longer wear to your tips and swivel arm, nozzles
and brush skirt (if applicable).
The tips that have been installed on your surface cleaning
system permit the use of your cleaner with a pressure
washer producing up to 7 GPM at 4000 PSI. Please note
that the 12" Whirl-A-Way can only be used with a pressure
washer producing up to 2500 PSI. Periodically check the
tips to ensure they are not plugged by dirt particles. As
this can cause the rotary arm to stop spinning. Or stripping
to be left on the surface being cleaned.
It is very important when operating your Whirl-a-Way,
that you maintain a continuous motion to ensure an even
clean. The distance of the nozzle tips from the surface
can be adjusted by loosening the bolt on the rotary head
mounting collar and adjusting the rotary head up or down.
Be certain the allen head bolt is tightened again to prevent
the rotary head from moving during operation. Please
ensure that your rotary head is adjusted to maintain a
minimum of 1” clearance between the spray tips and the
surface being cleaned.
OPERATING INSTRUCTIONS
13 2
T
he ro ta ry hea d h as a s ix -m ont h w ar ra nty from
the date of purchase. Should you encounter problems with the
rotary head within that time period, simply return the defective part
for warranty to the place of purchase. If you encounter problems
after the six month period has lapsed, we sell a rotary head repair
kit. You can use this kit to replace the components inside the rotary
head very quickly.
There is no warranty on the nylon brush ring.
All other components of the surface cleaning system have a 90-day
warranty against manufacturer’s defects only.
A repair kit for this Whirl-a-Way’s rotary head is
available. If you encounter problems with the rotary
head after the six month warranty has expired, this
repair kit (part #85.790.010) allows you to replace the
inner components very quickly.
The rotary head has a snap ring on the bottom holding
all the bearings inside. By removing the snap ring and
washer, you can tap off the outer shell with a rubber
hammer while the output shaft is held in a vice. The
rotary head repair kit can then be used to replace the
worn items inside the rotary head shell.
ROTARY HEAD REPAIR PARTS
WARRANTY
1) If water is leaking from the bypass port in the bottom of the
rotary head: Inspect the viton O-Ring in the rotary head.
2)Rotary Arm doesn't spin:
•Remove, inspect and clean nozzles. Replace if damaged
•Rotary head may not have been greased.
•Ensure there is no water leaking from the bypass port on the rotary head.
3)Leaves stripping:
•Ensure nozzles aren't damaged or plugged.
•Ensure rotary arms are straight.
1
2
3
TROUBLE SHOOTING
14
Bypass Port
Grease nipple
Viton O-Ring
Viton O-Ring
Loading...