BDI Sweep, 8438 Assembly Instructions Manual

1
B1 - Hex Driver x 1
B2 - Hex Wrench x 1
Sweep is engineered for easy assembly. Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Step 1 Unpack and Identify
Unpack and identify the components at left. Note that some components are shipped inside the cabinet. The assembly workspace should be a non-marring surface such as clean carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. For all other concerns, please contact your BDI Retailer.
Component List
Designed by Louis A. Lara.
These distinctive product congurations are protected by US and
international patents, trade dress, and/or copyright laws. BDI are trademarks of Becker Designed, Inc. All Rights reserved. ©2015, BDI Made in China. 8438REV083115v1
sweep
8438
cabinet
assembly instructions
bdiusa.com customerservice@bdiusa.com
C - 1/4-20 x 70 mm Screw x 2
D - 1/4-20 x 15 mm Screw x 16
E - Cabinet x 1
F - Metal Leg x 2
G - Wood Leg x 1
HL - Adjustable Shelf x 1
HR - Adjustable Shelf x 1
IR - Adjustable Shelf x 1
IL - Adjustable Shelf x 1
J - Back Panel x 2
J
E
HL
HR
IR
C
D
F
G
F
D
IL
2
assembly instructions
bdi
usa.com customerservice@bdiusa.com
sweep
84 38 ca bi ne t
Step 2 Build Base Assembly
With the help of another person, position the cabinet on its back. Attach Metal Legs (F) to Cabinet (E) using Screws (D) and tighten with Hex Driver (B1). Attach Wood Leg (G) to Cabinet (E) using Screws (C) and tighten with Hex Driver (B1).
Step 3 Turn Cabinet Over and Install Back Panels With the help of another person, position the cabinet right side up. Install Back Panels (J) to the backside of the cabinet by inserting top edge in upper channel then tipping
bottom edge forward and into lower channel. NOTE: Velcro straps are included for your convenience to facilitate wire management.
TWO PERSON ASSEMBLY
TWO PERSON ASSEMBLY
C x 2
D x 16
G
E
F
F
D
D
D
D
C
C
B1
J
1
1
2
2
3
assembly instructions
bdi
usa.com customerservice@bdiusa.com
sweep
84 38 ca bi ne t
Step 4 Adjust Shelf Height If desired, lift Adjustable Shelf (H, I) away, loosen & remove related Shelf Support Pins, reinstall the Shelf Support Pins at desired height, then reinstall
Adjustable Shelf.
I H
4
assembly instructions
bdi
usa.com customerservice@bdiusa.com
sweep
84 38 ca bi ne t
Fine tuning your new BDI Sweep Home Theater Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for your Sweep AV cabinet. Due to jostling in freight or perhaps an uneven floor, the doors on your Sweep cabinet may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that depending on your situation, patience and a bit of trial and error are required. The high-quality European hinge hardware is infinitely adjustable, but changing one element can cause the need for further adjustments. Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are sitting perfectly on your Sweep unit.
STEP 1 - Level your Sweep unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg using Hex Wrench (B2). If your floor is uneven, you may extend one or more levelers to attain a level, stable cabinet
placement. Turning the leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
CORRECT! Door is sitting squarely and evenly spaced on tops and sides.
INCORRECT! Door is out of alignment with the rest of the unit.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing against the door frame.
If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment to the European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can modify the orientation of the cabinet doors
to make sure that they hang perfectly within your cabinet.
Use the Phillips Screwdriver (A) supplied to adjust Sweep's door hinges:
• By adjusting Screw 1, the door will move LEFT or
RIGHT within the frame. Make minor adjustments at both top and bottom hinges for best results.
• By adjusting Screw 2 the entire door will move IN or
OUT, opening or closing the gap between the door frame and cabinet. (This screw rarely needs adjustment.)
1.
2.
2.
1.
Loading...