Page 1
KRONOSTM 6729
Credenza
bdiusa.com
customerservice@bdiusa.com
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today and you will be entered to win free a BINK
table from BDI. www.bdiusa.com/product-registration/
Placement and Maintenance
Kronos™ Office furniture is designed for indoor use on level floors.
Clean surfaces with a moist cloth.
Your Kronos™ Office furniture is engineered for easy assembly. Carefully
follow this procedure to prevent any damage. Do not use power tools for
assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, please contact BDI Customer Service at:
customerservice@bdiusa.com.
For all other concerns, please contact your BDI retailer.
Tool:
T1 Phillips screwdriver
H5 Phillips Machine
Screw x 20
C4 Small File Bar x 2
C5 Large File Bar x 1
C6 File Bar Clip x 6
A1 Cabinet
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Kronos & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2017, BDI
Made in China. 07.07.2017 v2
C7 Swivel Caster x 2
C8 Locking Swivel
Caster x 4
Page 2
Step 2 - Lay cabinet A1 on its back side. Using Phillips screw driver T1 and phillips machine screws H5,
install casters C8 and C9 to bottom panel as shown below.
H5 x 20
A1
C7
C8
C8
T1
C7
C7 x 2
C8
C8
C8 x 4
Step 3 - Stand upright / Adjust shelf if needed
With help from another person, carefully lift cabinet onto its wheels. The adjustable shelf may be repositioned
up or down as shown below.
2 Person Ta sk
2
KRONOS 6729
CREDENZA
customerservice@bdiusa.com
bdiusa.com
Page 3
Step 4 - File Bar Installation (forward facing files)
For letter files facing forward, attach file bar clips C6 to both ends of small file bar C4 as shown. Insert them
over the metal rails and into the notches in the front and back of the drawer
C6
C4
C4
Step 4B - File Bar Installation (sideways facing files)
For letter files facing sideways, attach file bar clips C6 to both ends of long file bar C5 as shown. Insert them
over the metal rails and into the notches in the sides of the drawers near the back. For legal size, simply remove
the file bars and hang the file folders on the front and back rails of the drawer.
C6
C5
C5
C6
3
KRONOS 6729
CREDENZA
bdiusa.com
customerservice@bdiusa.com
Page 4
STEP 5 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame. If the cabinet’s doors appear out of alignment, this condition can be corrected with minor
adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can
modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet.
Use the Phillips Screwdriver T1 supplied to adjust the door hinges:
• By adjusting Screw 1, the door will move LEFT or RIGHT within the
frame. Make minor adjustments at both top and bottom hinges for
best results.
• By adjusting Screw 2, the door will move UP or DOWN. For best
results, adjust Screw 2 on both the top and bottom hinges.
• By adjusting Screw 3 the entire door will move IN or OUT, opening
or closing the gap between the door frame and cabinet. (This screw
rarely needs adjustment.)
2
1
3
Example:
Tightening screw 1
on top hinge will move the
top of the door in the
direction shown
Example:
Adjusting screw 2
on both hinges (same direction)
will move the door up or down
4
KRONOS 6729
CREDENZA
bdiusa.com
customerservice@bdiusa.com
Loading...