Page 1
HIGH PERFORMANCE
FURNITURE FOR YOUR
HOME THEATER
4/2007
Avion Noir
Assembly Instructions
TM
8537 & 8539
Page 2
Avion Noir™ Home Theater Furniture
Component List
A - Avion Noir Cabinet x 1
B - Sliding Back Panel x 2
Velcro Strap x 5
Your Avion Noir
assembly. Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Avion Noir™ Home Theater Furniture is designed for indoor use on
level floors. Clean glass with glass cleaner. Clean steel parts and
wood veneer with a moist cloth.
NOTE: Hardware contents located inside top center drawer.
Step 1
Unpack and identify the parts listed above.
The assembly workspace should be a non-marring surface such as carpet.
For missing hardware pieces, please contact BDI Customer Service at:
customerservice@bdiusa.com
All other concerns please contact your local BDI Retailer.
Install legs.
Remove all internal components from the cabinet including shelves, and
hardware box.
™
Home Theater Furniture is engineered for easy
www.bdiusa.com
customerservice@bdiusa.com
C - Metal Leg x 3
Small Hex Wrench x 1
Gromet x 2
D - Adjustable Shelf x 2
E - Shelf Pin x 8
Phillips Screwdriver x 1
F - Handle x 4
G - Nylon Screw x 8
Medium Hex Wrench x 1
H - Mounting Screw x 12
Speaker Drawer Panel x 1
Designed by BDI Design Studio.
‘Avion Noir’ is a trademark of Becker Designed, Inc.
All rights reserved. ©2006 Becker Designed, Inc.
Carefully lay cabinet (A) updside down (Step 1).
Using the medium hex wrench, screw the metal leg (C) to the bottom of the
cabinet with mounting screw (H). NOTE: Each of the metal legs have
adjustable levelers that can be adjusted from inside the cabinet using the small
hex wrench.
H
A
Step 2
Adjustable shelf pins (E) may be
repositioned depending on the height
of your component, allowing you to
raise or lower the adjustable shelf to the
desired level.
Install adjustable shelf (D) inside
the left and right cabinet area.
NOTE: To place the adjustable shelf
inside the cabinet, the shelf must be
tilted sideways to clear the door.
D - Adjustable Shelf
E - Shelf Pin
2
Page 3
Step 3
Install handles (F) on doors and drawers using the nylon screw (G)
using the Phillips screwdriver supplied.
F
G
Phillips Screwdriver
Detail: rear view of the door.
Step 4
Install both sliding back panels (B) to the backside of the cabinet.
NOTE: Velcro straps are included as wire management for your convenience.
Gromet x 2
Step 5
Center channel speaker option A.
If you decide to use your top/center drawer area for a center channel
speaker, the drawer may be easily removed. In order to do this, follow the
steps below.
Fully extend drawer and locate plastic lever
on drawer slide.
Simultaneously on the LEFT side of drawer, lift UP on plastic lever AND on the RIGHT side
of drawer, push DOWN on plastic lever and pull STRAIGHT OUT the entire drawer assembly.
Remove drawer slides from interior side panels using a Phillips screwdriver.
B
+
3
Page 4
Center channel speaker option B.
If you decide to use your top/center drawer area for a center channel
speaker, the glass drawer face may be replaced with speaker drawer
face. In order to do this, follow the steps below.
1. Pull out drawer and locate all exposed Cam inserts. Cam inserts
are located inside drawer and bottom side of drawer shelf.
2. Remove glass drawer face from drawer assembly by turning all
Cam inserts (counter clock-wise) using a Phillips screwdriver.
3. Switch all previously removed hardware over to back side of
speaker panel.
4. Install speaker panel to drawer assembly and tighten Cam inserts.
Large Cam Screw
Small Wood Dowel
x 2
x 4
Large Wood Dowel
x 2
Small Cam Screw
x 2
4
Page 5
Fine tuning your new BDI Avion Home Theater Furniture
These steps are to be followed after you have unpackaged and completed the simple assembly instructions for your Avion or
Avion Noir stand. Due to jostling in freight or perhaps an uneven floor, the doors and drawers on your Avion stand may not
appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that depending on
your situation, patience and a bit of trial and error are required. The high-quality European hinge hardware is infinitely
adjustable, but changing one element can cause the need for further adjustments. Through a little adjustment, you can
modify the orientation of the cabinet doors to make sure that they are sitting perfectly on your Avion unit.
INCORRECT! Door is
out of alignment with
the rest of the unit.
STEP 1 - Level your Avion unit (if needed)
The levelers which are concealed within the legs can be adjusted from inside the
Avion cabinet to compensate for an uneven floor or to secure your cabinet so that it
does not roll. If you are having difficulty with misaligned doors, it is recommended
that you first retract all levelers and make sure that the unit is resting on it’s wheels.
If the center section on a three-legged unit appears to be sagging (center doors
hangs below the side doors) raise the levelers on the center leg to compensate for
this.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your Avion stand should be perfectly spaced
and the doors should open and close freely without
rubbing against the door frame. Adjustments may be
made to the Avion door hinges with the use of a Phillips
head screwdriver. The hinge hardware has three
adjustment screws.
CORRECT! Door is
sitting squarely and
evenly spaced on tops
and sides.
Step 1: Level your Avion unit.
• By adjusting Screw 1, the door will move left and right
within the frame. For best results, make minor adjustments
to top and bottom hinge for best results.
• If adjusting Screw 1 has not achieved the desired result,
you can adjust Screw 2 and the door will move up and
down within the frame (the top and bottom hinges need to
be adjusted the same amount).
• Adjusting Screw 3 will cause the entire door to move
in and out, opening and closing the gap between the door
frame and cabinet. This screw rarely needs adjustment.
Step 2: Adjust Door Hinges.
HIGH PERFORMANCE FURNITURE
5
Loading...