Page 1
Re v o
9981
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
A -
Glass Shelf x 2
B -
Shelf Pin x 8
Pre-installed
Retention Clip x 8
C -
Pre-installed
D - Phillips Screwdriver
x 1
E -
Allen Wrench x 1
F - Swivel-Lock Pin x 2
Pre-installed
Your Revo Home Theater Furniture is engineered for easy
assembly. Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Revo Home Theater Furniture is designed for indoor use on level
floors. Clean glass with glass cleaner, and steel parts and wood
veneer with a moist cloth.
Step 1
Unpack and identify the parts listed above. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at customerservice@bdiusa.com. For all other concerns, please
contact your BDI Retailer.
Step 2
Revo 9981 features a swiveling base. Note that Swivel-Lock Pins
are factory-installed at Position 1 enabling the stand to swivel
(F)
15-degrees to left and 15-degrees to right.
To lock the stand in a fixed position, use provided
Allen Wrench
(E) to remove both Swivel-Lock Pins (F) from Position 1 (factory
position) and re-install them at Position 2.
Position 2
Position 1
NOTE: Choosing not to use the
Swivel-Lock Pins (F) will enable
360-degrees of rotation.
F
Front
Designed by Louis Lara.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc. All Rights reserved. ©2009, BDI
9981REV092409v8
1
Page 2
Retention clip (C)
1
1
44
Shelf pin (B)
A x 2
Step 2
Confirm that Shelf Pins (B) are pre-installed.
In order to adjust height, one must remove
the glass retention clip (secured by the
shelf pin) that holds the glass shelves in
place.
Loosen the 4 1. Shelf Pins (B)
1 turn with Phillips Screwdriver
(D).
Remove 2. Retention Clips (C) ( x 4 )
Unscrew 3. Shelf Pins (B) completely
Reposition the 4. Shelf Pins (B) at
desired height
Detail of Shelf Pin (B) and
Retention Clip (C)
Secure Glass Shelves
To secure the shelves on your Revo unit, it is
necessary to use the
is secured by the
Retention Clip (C), which
Shelf Pin (B).
Install 5. Glass Shelves (A x 2)
Install 6. Retention Clips (C)
as shown in
“Pin Assembly Diagram”
Secure by tightening the7.
Shelf Pin (B)
with Phillips Screwdriver (D).
Pin Assembly Diagram
1 : Retention clip (C)
2 : Glass Shelf (A)
3 : Shelf Pin (B)
4 : Cabinet wall
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Page 3
1.
2.
3.
3.
1.
2.*
2.*
Step 4
Install Back Panel.
The back panel comes pre-installed. Follow illustrations below for
installation and removal.
Step 5
Adjust Door Hinges (if needed)
If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment
to the European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the
need for adjustments to other elements. But with a few adjustments, you can modify the orientation of
the cabinet doors to make sure that they hang perfectly within your cabinet.
3.
2.
3.
1.
2.
1.
Figure 2Figure 1
Use a Phillips screwdriver to adjust Revo’s door hinges:
By adjusting • Screw 1,
adjustments at both top and bottom hinges for best results.
the door will move LEFT or RIGHT within the frame. Make minor
By adjusting • Screw(s) 2, the door will move UP or DOWN within the frame (the top and bottom
hinges must be adjusted the same degree).
NOTE: If your hinges have a Slotted Mounting Plate (as shown in Figure 2): Loosen Screws 2
one complete turn, raise or lower door, then hold in position while tightening Screws 2 (on both
hinges).
By adjusting • Screw 3 the entire door will move IN or OUT, opening or closing the gap between the
door frame and cabinet. (This screw rarely needs adjustment.)
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...