Page 1
®
V ista
9950and9960
assembly instructions
bdiusa.com customerservice@bdiusa.com
Component List
Large Hex Wrench x 1
Small Hex Wrench x 1
A - Base x 1
B - Adjustable Glides x 5
D - Spine x 1
E - 3/8 x 1.25” Flat Head
Screw x 4
Your Vista® Home Theater Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Vista® Home Theater Furniture is designed for indoor use on level floors.
Clean glass with glass cleaner and steel parts with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components. Note that some components are
shipped inside the cabinet. The assembly workspace should be a nonmarring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
N - Shelf Brackets
2 Left + 2 Right with 9960
O - Glass Shelf
x 2 with Model 9960
P - M8 x 1.5” Flat Head Screw
x 4 with 9960
HTL
HBL
FBFF
HTR
HBR
FF - Front Panel x 1
FB - Back Cover Panel x 1
G -5/8” Long Phillips Head
Screw
Screen Brackets x 4
I - 5/16 x .75” Pan Head
Screw x 16
L - Washer x 4
x 3
S - Horizontal Mounting Bars x 2
T - Small Spacers x 4
U - Large Spacers x 4
V - Phillips Head Mounting Screws
(various thread sizes) x 32
Q
R
Q - Wire Management Strap x 3
R - Plastic Fastening Pin x 3
M - Nut x 4
Designed by Louis A. Lara
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws. “Vista” and BDI are trademarks of
Becker Designed, Inc. All Rights reserved. ©2011, BDI
Made in China. 99509960REV072711v3
1
Page 2
E x 4
B - Adjustable
Glides x 5
D - Spine
A - Base
G x 1
FF - Front
Panel x 1
Step 2
Figure 1
Attach Glides
Thread Adjustable Glides (B) into holes on underside
of Base (A) (Figure 1).
Step 3
Attach Spine
Attach Spine (D) to Base (A) using 4 - 3/8 x 1.25”
Flat Head Screws (E) and Large Hex Wrench
provided (Figure 1).
HTR
HBR
I x 16
HTL
HBL
N - Shelf Brackets
2 Left & 2 Right
Step 4
Figure 2
Attach Front Cover Panel
Install Front Cover Panel (F) to front of spine using
5/8” Long Phillips Head Screw (G) as shown (Figure
2). Bottom end of cover panel is attached with hook
and loop pads. Note: The front cover panel has a
flatter curve. Back panel has a notch at the bottom.
P x 4
Step 5
Figure 3
Attach Shelf & Screen Brackets
Attach Shelf (N) & Screen Brackets (HTR, HTL,
HBR, HBL) as shown with 3/4” Pan Head Screws
(I) (Figure 3) using Large Hex Wrench. Slots on the
face of the screen brackets should face forward.
Screen brackets may need to be adjusted up or
down to align with horizontal bars.
O - Shelves
x 2
Note: Each shelf
will support up to
50 lbs (23 kg).
Step 5
Figure 4
Install glass shelves.
First, position Glass Shelf (O) so that discs are
resting on the ends of the Shelf Brackets (N).
Keeping one hand on the shelf, pick up one M8 x
1.5” Flat Head Socket Screw (P) and thread up
through the bottom of the cylinder into the hole
on the bottom of the glass mounting disc. Thread
second screw into second disc. Using Small Hex
Wrench, fully tighten both left and right discs.
2
assembly instructions
bdiusa.com customerservice@bdiusa.com
Page 3
Flat Screen TV
(back view)
Pre-threaded
Nut (M) to
upper UMB
bar.
Short Mounting
Screws (V)
Washers (L)
Step 6
Install Horizontal Mounting Bars
Figure 5
Find mounting screws that came with your flat
screen TV. If screws are not available, find the
Short Phillips Head Mounting Screws (V) provided
with Vista that thread cleanly into the mounting
holes in the back of your TV. The following thread
sizes are included: M5, M6, M8, 10-32 & 1/4-28.
Attach both Horizontal Mounting Bar (S) to TV as
shown (Figure 5) using Washers (L) and Phillips
driver. Note: If back of TV has a curved surface, or,
if bars do not sit flat, use Spacers (T or U) and Long
Mounting Screws (V) provided. Make sure bars are
centered left to right! Button hooks should be on top
and threaded studs on bottom. Fully tighten bars to
TV!
Q - Wire Management
Strap x 3
R - Plastic Pin
x 3
Nut
Threaded stud
(M)
Step 7
Figure 6
Attach flat screen TV
Carefully “hook” TV onto screen brackets as shown
(Figure 6). Make sure both pre-threaded nuts drop
into key hole slot and that threaded studs go into slot
on Bottom Screen Brackets (HBL & HBR). Tighten
Nuts (M) using wrench. Note: Vista will support flat
screens up to 225lbs (102kg). Note: Vista is NOT
designed to support televsions greater than 6” in
depth.
Step 8
Figure 7
Install Wire Management Straps
Wire Management Straps (Q) attach to the
perforated metal panel inside the Vista spine simply
by pushing the Plastic Pin (R) into the hole in the
center of the strap and into one of the holes on
the panel (Figure 7). Wrap straps around cords as
shown (Figure 8). Straps may be relocated simply by
pulling out and pushing plastic pin into another hole.
Step 9
Figure 4
Install Back Cover Panel
When all wires are in place and secured, install
Back Cover Panel (FB) using 2 remaining 5/8” long
Phillips Head Screws (G). Carefully, move Vista into
place by pulling and lifting on lower shelf bracket
elbows. Adjust glides if necessary.
3
assembly instructions
bdiusa.com customerservice@bdiusa.com
Loading...