Page 1
a s s e m b l y i n s t r u c t i o n s
De p l o y® & De p l o y® Ma x
9624, 9628, 9629, 9634, 9638,
9639, 9640, 9640-1 ,9644, 9649
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
A - 4mm Hex Driver
x 1
B - Assembled Frame
x 1
C - Shelf Pin x 4
(Models 9628, 9638)
x 8
D - Rubber Bumper Insert
(Models 9624, 9629,
9634, 9644, 9639,
9649)
x 15
(Model 9640, 9640-1)
x 18
(Models 9628, 9638)
x 24
E - Sliding Back Panel
x 1
Deploy® is engineered for easy assembly. Carefully follow this
procedure to prevent any damage.
Placement and Maintenance
®
Deploy
is designed for indoor use on level floors. Clean glass with
glass cleaner, and steel parts and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at customerservice@bdiusa.com. For all other concerns, please
contact your BDI Retailer.
Step 2
Unfold the metal legs on the Assembled Frame (B). Install the
Shelf Pins (C) into the desired location on the folding metal legs
and the inside area of the wood frame using the Hex Driver (A).
Install the Rubber Bumper Inserts (D) to the Assembled Frame
(B).
F - Threaded Knob x 4
G - Center Shelf Support
x 1
(Models 9628, 9638)
x 2
H - Center Glass Shelf x 2
(Models 9628, 9638)
x 3
I - Top Glass Shelf x 1
J - Velcro Strap and
Wood Screw
x 9
C
B
A
D
Designed by by BDI Design Studio.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
“Deploy” and BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2009, BDI
Made in China. 962496299640-19644964996349639REV012210v2
1
Page 2
Step 3
Insert back panel
Once the metal legs are opened, slide the Back Panel (E) down
into the “U” channel
E
B
Step 4
Secure back panel
Then tighten the four Threaded Knobs (F) to secure back panel
into position.
NOTE: Threaded Knobs (F) are included with the Assembled
Frame (B)
F
E
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Page 3
Step 5
Installing the Rubber Bumper inserts and Center Shelf Support
Install the Rubber Bumper Inserts (D) to all of the hole locations
on the Center Shelf Support (G). Then install the Center Glass
Shelf Support (G) by placing on the previously installed shelf pins.
D
G
B
Step 6
Install the glass shelves
Install the Center Glass Shelves (H) and Top Glass Shelf (I).
I
H
B
G
Step 7
Cable Management
Velcro Straps and Wood Screws (J) are supplied, and can be
used for organizing cable management. On the rear side of the
back panel are pre-drilled holes for installing the Velcro Straps
(J) using a Phillips screw driver.
J
C
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...