Page 1
I c o n
9424
a s s e m b l y i n s t r u c t i o n s
®
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
Arm x 2
Glass Top x 1
Back Panel x 1
Shelf Brackets x 2
Front Frame x 1
Glass Shelves x 2
Base x 1
A x 6
B x 4
C x 8
D x 2
E x 8
Your Icon® Home Theater Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
Placement and Maintenance
Icon® Home Theater Furniture is designed for indoor use on level floors.
Clean glass with glass cleaner, and steel parts and wood veneer with a
moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some components
are shipped inside the cabinet. The assembly workspace should be a nonmarring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
Step 2
Install Arms
Bracket mounting holes should face inward.
F x 6
G x 1
H x 1
I x 2
J x 2
K x 5
L x 5
D x 2
G
Step 3
Install Levelers and Frame to Base
Install Levelers (F) to bottom of Base. Adjust Levelers (F) so Base is level
and stable. Use shown hardware to attach Base to Frame.
J x 2
F x 8
Designed by Cristian Wicha & Bill Becker.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws. “Icon” and BDI are trademarks of
Becker Designed, Inc. All Rights reserved. ©2010, BDI
Made in Taiwan. 9424REV03112010v2
I x 2
H
A x 2
G
1
Page 2
Step 4
Install the Shelf Brackets
Shelf Brackets can be adjusted to offer three different shelf positions.
Shelf Brackets x 12
E
E
Step 5
Install Back Panel and Wire Managements Straps
Back Panel is to be installed with small holes facing backward.
Velcro straps are supplied to control cables. They can be screwed into
the steel at top and bottom of the arm or into the small holes on the
Back Panel.
K
L
E x 4
H
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Page 3
Step 6
Install Glass Shelves
Use appropriate hardware. Apply Felt Washers to the stainless
pucks prior to glass installation.
PLEASE READ: Leave glass screws loose until all screws have been
installed. Then tighten securely. It may be nexessary to lossen Shelf
Brackets to obtain proper fit. Once Glass Shelves and Top Glass
are fitted, PLEASE BE CERTAIN TO GO BACK AND TIGHTEN ALL
SCREWS.
Top Glass
A x 32
B x 2
C x 4
Shelf Glass
B x 2
C x 2
Bottom Shelf Glass
A x 2
C x 2
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Page 4
CORRECT CORRECT
Minimum o f
3 "
steel
frame
CENTER LINE
INCORRECT
steel
frame
INCORRECT
i m p o r t a n t n o t i c e
®
I c o n
9424 & 9429
Icon Models 9424 & 9429 are engineered specifically for Flat Panel Plasma and LCD TVs.
If a micro-display rear projection TV is used, the TV must be positioned as far back as possible
while still being fully supported by the glass. Minimum 3” (75 mm) from front edge of glass.
Consult BDI’s website (www.bdiusa.com) or sales brochure for recommended TV sizes.
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Do not position a
Flat Panel TV such
that the screen on
the front side of the
steel frame.
Position the Flat Panel
TV so that the screen
is positioned behind
the steel frame.
A Rear Projection
TV must be
positioned a
minimum of 3”
from front edge
oof glass while not
hanging over the
rear of the unit.
Footprint of
TV must not
overhang
the glass
4
Loading...