Page 1
braden
8828
a s s e m b l y i n s t r u c t i o n s
bdiusa.com cust omerservice@bdiusa.com
Component List
A - Phillips Screwdriver
x 1
B - Hex Driver
x 1
C - Assembled Cabinet
x 1
D - 1/4-20 x 4"
Machine Screw
x 10
E - Side Wood Legs
x 2
F - Inner Wood Legs
x 2
Braden is engineered for easy assembly. Carefully follow this
procedure to prevent any damage.
Placement and Maintenance
Braden is designed for indoor use on level floors. Clean wood
veneer with a moist cloth. Clean glass with glass cleaner.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some
components are shipped inside the cabinet. The assembly
workspace should be a non-marring surface such as carpet. For
missing hardware pieces, please contact BDI Customer Service
at customerservice@bdiusa.com. For all other concerns, please
contact your BDI Retailer.
G - M4 x 25mm Screw
x 6
H - Pull
x 3
I - Glass Shelf
x 1
J - Adjustable Shelf
x 2
K - Back Panel x 2
Designed by Matthew Weatherly.
These distinctive product congurations are protected by US and
international patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2012, BDI
Made in China. 8828REV1110212v1
1
Page 2
Step 2
Install Legs
Carefully lay Assembled Cabinet (C) on its back. Using Hex Driver (B),
attach the Side Wood Legs (E) and Inner Wood Legs (F) to the bottom of
the Assembled Cabinet (C) with 1/4”-20 x 4" Machine Screws (D).
C
D
D
E
F
D
D
E
D
D
Step 3
Install Pulls
Position the cabinet upright and install door Pulls (H) using the M4 x
25mm Screws (G) and the Phillips Screwdriver (A) supplied.
F
D
D
D
G
H
G
braden
88 28
2
ass embly instruc tion s
bdiusa.com customerservice@bdiusa.com
Page 3
Step 4
Install Glass Shelf (I)
Install Glass Shelf (I) so that the front
edge of the shelf is flush with the
cabinet.
I
Step 5
Install Back Panels
Install both Back Panels (K) to the backside of the cabinet by inserting top
edge in upper channel, then tipping bottom edge forward and into lower
channel.
NOTE: Velcro straps are included as wire management for your convenience.
1
The shelf pins located inside the
left and right cabinet space may be
repositioned, allowing you to raise
or lower each Adjustable Shelf (J)
to the desired level.
2
Optional Flat Panel TV Mount
braden
88 28
This BDI cabinet is compatible with BDI’s Arena Flat-Panel TV
Mount #9972 (sold separately), with the following features:
• accommodates most TVs up to 65", 175 lbs
• swivel allows rotating for optimal viewing
• allows adjustable TV mounting height
• accepts and routes cables to and from the TV
For more information, visit www.bdiusa.com
3
ass embly instruc tion s
bdiusa.com customerservice@bdiusa.com
Page 4
Fine tuning your new BDI Braden Home Theater Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your Braden AV stand. Due to jostling in freight or perhaps an uneven floor, the doors on your Braden stand
may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware
that depending on your situation, patience and a bit of trial and error are required. The high-quality European
hinge hardware is infinitely adjustable, but changing one element can cause the need for further adjustments.
Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are
sitting perfectly on your Braden unit.
STEP 1 - Level your Braden unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg and are
hand-adjustable. If your floor is uneven, you may extend one or more levelers to attain a level, stable cabinet
placement. Turning the leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
INCORRECT! Door is
out of alignment with
the rest of the unit.
CORRECT! Door is
sitting squarely and
evenly spaced on tops
and sides.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame.
If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment to the
European hinges on each door.
Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the need for
adjustments to other elements. But with a few adjustments, you can modify the orientation of the cabinet doors
to make sure that they hang perfectly within your cabinet.
*
2.
Use the Phillips Screwdriver (A) supplied to adjust Braden’s
door hinges:
• By adjusting Screw 1, the door will move LEFT or
RIGHT within the frame. Make minor adjustments
at both top and bottom hinges for best results.
• By adjusting Screw(s) 2, the door will move UP or
DOWN within the frame (the top and bottom hinges
must be adjusted the same degree). NOTE: Loosen
Screws 2 one complete turn, raise or lower door, then
hold in position while tightening Screws 2 (on both
hinges).
2.
2.
3.
*
1.
• By adjusting Screw 3 the entire door will move IN or
3.
1.
OUT, opening or closing the gap between the door
frame and cabinet. (This screw rarely needs adjustment.)
braden
88 28
4
ass embly instruc tion s
bdiusa.com customerservice@bdiusa.com
Loading...