Page 1
Marina
8729-2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
A - Phillips Screwdriver
x 1
B - Allen Wrench x 1
C - Assembled Cabinet
x 1
D - Adjustable Shelf x 2
E- Back Panel x 2
Marina® is engineered for easy assembly. Carefully follow this procedure
to prevent any damage.
Placement and Maintenance
®
Marina
is designed for indoor use on level floors. Clean glass with glass
cleaner; steel parts and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, please contact BDI Customer Service at customerservice@
bdiusa.com. For all other concerns, please contact your BDI Retailer.
Step 2
Leveling and Shelf Adjustment
The adjustable leveler glides on
the bottom, mid section of the
cabinet are accessible from
inside the cabinet using the Allen
Wrench (B).
Shelf Pin
The shelf pins located inside the
left and right cabinet space may
be repositioned, allowing you to
raise or lower the shelf to the
desired level.
For more information about the adjustable
levelers and troubleshooting, be sure to
check out “Fine tuning your new BDI Marina
Home Theater Furniture” at the end of these
instructions.
Designed by Cristian Wicha.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI is a trademarks of Becker Designed, Inc.
All Rights reserved. ©2010, BDI
Made in China. 8729-2REV12131010v6
1
Page 2
Step 4
Install Back Panel (E) to the rear side of cabinet in the
pre-determined slots. Velcro straps are included as wire
management for your convenience.
9970
I
Optional Flat Panel TV Mount
9972
This BDI cabinet is compatible with both the BDI’s
Cabinet Flat-Panel TV Mount #9970
Freestanding Flat-Panel TV Mount (sold separately)
with the following features:
accommodates most TVs up to 60” •
swivel allows for rotating for optimal viewing •
allows adjustable TV mounting height •
accepts and route cables to and from the TV •
or more information, visit www.bdiusa.com
F
2
and the #9972
,
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Page 3
Thank you for choosing BDI.
1.
2.
3.
3.
1.
2.
*
2.
*
Your BDI home theater cabinet is engineered to include a range of adjustments. Please read and retain this guide so
that you can fully enjoy the look and use of your cabinet for years to come.
Unless manual leveling is required or you wish to prevent the cabinet from rolling, you may prefer to keep the cabinet’s
levelers up and off the floor. This allows easier cabinet movement for greater access to rear panels and wiremanagement, and permits easier cleaning/vacuuming underneath the cabinet.
By following the steps in this guide, you can be sure that your BDI cabinet is in optimum tune and adjustment. If you need
additional assistance, contact BDI at customerservice@bdiusa.com.
Fine tuning your BDI Home Theater Furniture
After unpacking and assembling your cabinet, inspect it to be sure that it is sitting level on the floor, that all doors appear
level, and that they open and close freely without rubbing or binding.
Due to uneven floors or perhaps gentle jostling during shipment, your BDI cabinet may not appear to be in perfect
alignment when first assembled or when loaded with heavier electronic equipment. Such alignment issues are usually
minimized or eliminated with only a few minor adjustments.
STEP 1 - Level your Marina unit
Levelers are integrated into each leg assembly and are accessed from inside the cabinet. If your floor is uneven, you may
extend one or more levelers (with the provided Allen Wrench (B)) to attain a level, stable cabinet placement. Turning the
leveler clockwise will extend the leveler; turning it counter-clockwise will retract it. (Refer to diagram in Step 2)
INCORRECT!
Door is out of
alignment with
the rest of the
unit.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing against
the door frame.
If the cabinet’s doors appear out of alignment, this condition can
be corrected with minor adjustment to the European hinges on
each door.
Because these hinges are infinitely adjustable, adjusting one
hinge element can sometimes cause the need for adjustments
to other elements. But with a few adjustments, you can modify
the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use a Phillips screwdriver to adjust the door hinges:
By adjusting
• Screw 1, the door will move LEFT or RIGHT
within the frame. Make minor adjustments at both top and
bottom hinges for best results.
By adjusting • Screw(s) 2, the door will move UP or DOWN
within the frame (the top and bottom hinges must be
adjusted the same amount).
By adjusting • Screw 3 the entire door will move IN or OUT,
opening or closing the gap between the door frame and
cabinet (this screw rarely needs adjustment).
CORRECT!
Door is sitting
squarely and
evenly spaced
on tops and
sides.
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...