Component List
®
Novia
8424
A - Phillips Screwdriver x 1
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Your Novia® Home Theater Furniture is engineered for easy assembly.
Carefully follow this procedure to prevent any damage.
B - 4mm Hex Driver x 1
C - Leveler Wrench x 1
D - Leg Sections x 2
E - Cam Screws x 4
F - Small Wood Dowels x 8
G - Side Stretchers
x 2
H - Cam Lock Nuts x 4
(pre-installed)
I - Large Wood Dowels x 4
J - Assembled Cabinet x 1
Placement and Maintenance
Novia® Home Theater Furniture is designed for indoor use on level
floors. Clean glass with glass cleaner, and steel parts and wood veneer
with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some components
are shipped inside the cabinet. The assembly workspace should be a nonmarring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
Step 2
Build Base Assembly
First, remove all internal components from the cabinet including shelves,
hardware box and legs.
Install Cam Screws (E) into Leg Sections (D) and hand tighten. Insert
Small Wood Dowels (F) into legs on either side of the Cam Screws (E) as
shown in drawing.
Locate the Cam Lock Nuts (H) in the Side Stretchers (G). Loosen the
head of the Cam Lock Nuts (H) using the provided Phillips Screwdriver
(A).
K - 1/4-20 x 4” Bolts x 4
M - 1/4-20 x 1.5” Bolts x 6
N - Center Leg x 1
O - Top Glass x 1
P - M4 x 25mm Pull Bolts x 2
Q - Pull x 2
R - Adjustable Shelf x 2
S - Back Panel x 1
Place Stretchers so Cams are facing towards the wheels and the
grooved edge detail faces outward.
Attach Legs to Stretchers from both ends.
Tighten Cam Lock Nuts (H) using Phillips Screwdriver (A).
Designed by Matthew Weatherly
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
“Novia” and BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2009, BDI
Made in China. 8424REV120709v3
1
Step 3
Attaching Base Frame to Assembled Cabinet
Install the four (4) Large Wood Dowels (I) into the four corners holes
of the Assembled Cabinet (J) and tap in place. Then carefully lower the
assembled base frame over the Assembled Cabinet (J), aligning Large
Wood Dowels (I) into the corresponding base frame holes.
Step 4
Fasten Base Frame to Assembled Cabinet
NOTE: Don’t over tighten the bolts until they
are all in place! Once in place, tighten all bolts.
Using two (2) 1/4-20 x 4” Bolts (K) and the
4mm Hex Driver (B), fasten the leg sections
of the assembled base frame to the bottom of
the Assembled Cabinet (J)
.
Using six (6) 1/4-20 x 1.5” Bolts (M) and
the 4mm Hex Driver (B), fasten the side
stretchers of the assembled base frame to
the bottom of the Assembled Cabinet (J)
.
Using two (2) 1/4-20 x 4” Bolts (K) and the
4mm Hex Driver (B), install the Center Leg
(N) to the bottom of the Assembled Cabinet
. Place Center Leg so that the leveler is
(J)
towards the back of the cabinet.
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Step 5
Repositioning Assembled Cabinet
Carefully turn Assembled Cabinet (J) over and install Top Glass (O)
on top.
Install Pulls (Q) to the front side of the doors using M4 x 25
mm Pull Bolts (P) and Phillips Screwdriver (A).
The shelf pins located inside the left and right cabinet space
may be repositioned, allowing you to raise or lower the shelf to
the desired level.
Install Adjustable Shelf (R) inside the left and right cabinet area.
NOTE: To place the adjustable shelf inside the cabinet, the shelf
must be tilted sideways to clear the door.
Step 6
Installing Back Panel
Install Back Panel (S) to the rear side of cabinet. Velcro straps are
included as wire management for your convenience.
1.
2.
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
1.
2.
3.
3.
1.
2.
*
2.
*
Thank you for choosing BDI.
Your BDI home theater cabinet is engineered to include a range of adjustments. Please read and retain this guide so
that you can fully enjoy the look and use of your cabinet for years to come.
Unless manual leveling is required or you wish to prevent the cabinet from rolling, you may prefer to keep the cabinet’s
levelers up and off the floor. This allows easier cabinet movement for greater access to rear panels and wiremanagement, and permits easier cleaning/vacuuming underneath the cabinet.
By following the steps in this guide, you can be sure that your BDI cabinet is in optimum tune and adjustment. If you
need additional assistance, contact BDI at customerservice@bdiusa.com.
Fine tuning your BDI Home Theater Furniture
After unpacking and assembling your cabinet, inspect it to be sure that it is sitting level on the floor, that all doors
appear level, and that they open and close freely without rubbing or binding.
Due to uneven floors or perhaps gentle jostling during shipment, your BDI cabinet may not appear to be in perfect
alignment when first assembled or when loaded with heavier electronic equipment. Such alignment issues are usually
minimized or eliminated with only a few minor adjustments.
STEP 1 - Level the cabinet (if needed)
Levelers are integrated into each leg assembly and are accessed from outside
the cabinet. If your floor is uneven, you may extend one or more levelers (with the
provided Leveler Wrench (C)) to attain a level, stable cabinet placement. Turning the
leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
INCORRECT! Door is
out of alignment with
the rest of the unit.
CORRECT! Door is sitting squarely and evenly
spaced on tops and
sides.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing against the
door frame.
If the cabinet’s doors appear out of alignment, this condition can be
corrected with minor adjustment to the European hinges on each
door.
Because these hinges are infinitely adjustable, adjusting one
hinge element can sometimes cause the need for adjustments
to other elements. But with a few adjustments, you can modify
the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use a Phillips screwdriver to adjust the door hinges:
• Screw 1, the door will move LEFT
By adjusting
or RIGHT within the frame. Make minor adjustments at both
top and bottom hinges for best results.
By adjusting • Screw(s) 2, the door will move UP or DOWN
within the frame (the top and bottom hinges must
be adjusted the same amount).
opening or closing the gap between the door frame
By adjusting • Screw 3 the entire door will move IN or OUT,
and cabinet (this screw rarely needs adjustment).
4
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...