Novia
8421
a s s e m b l y i n s t r u c t i o n s
®
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
A - 4mm Hex Driver
x 1
B - Phillips Screwdriver
x 1
C - Leveler Wrench x 1
D - Glass Panel x 1
E -Assembled Cabinet x 1
F - Knob Screw x 4
G - Knob x 4
Novia® is engineered for easy assembly. Carefully follow this procedure
to prevent any damage.
Placement and Maintenance
®
Novia
is designed for indoor use on level floors. Clean glass with glass
cleaner; steel parts and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces please contact BDI Customer Service at customerservice@bdiusa.
com. For all other concerns, please contact your BDI Retailer.
Step 2
Install Glass Panel (D) on top of Assembled Cabinet (E).
D
H - Adjustable Shelf x 2
I - Back Panel x 1
E
For more information about the adjustable
levelers and troubleshooting, be sure to
check out “Fine tuning your new BDI Novia
Home Theater Furniture” at the end of these
instructions.
Designed by Matthew Weatherly
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
“Novia” and BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2009, BDI
Made in China. 8421REV071510v3
1
Step 3
Install Knob (G) to the front side of door and drawer using Knob Screw
(F) and Phillips Screwdriver (B).
The shelf pins located inside the left and right
cabinet space may be repositioned, allowing you
to raise or lower the shelf to the desired level.
B F G
Step 4
Install Back Panel (I) to the rear side of cabinet in the
pre-determined slots. Velcro straps are included as wire
management for your convenience.
1.
2.
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Option A
The flip-down door compartment may be used to house a center channel speaker
(up to 37.5” width x 10.5” depth x 8” height).
Option B
In conjunction with a center channel speaker, or component (up to 19.25” width x 15.5” depth x 8” height), this
area may be used to store DVD’s, VHS cassettes, and CD’s. In order to do this, remove center wood strip.
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Option C
Side compartment may be used to accommodate
a vertical standing video game unit. To do this,
first remove the wood strip and then adjustable
shelf.
Optional glass panel insert is available. Contact BDI
Customer Service at: customerservice@bdiusa.com
4
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Step 5
Leveling
There are a total of 6 adjustable levelers on the bottom of the cabinet,
which may be adjusted depending on your leveling situation.
C
A
Four of the six leg levelers are accessible near the
bottom of the side panels using the Leveler Wrench
(C).
Two of the six adjustable leg levelers on the bottom,
mid section of the cabinet are accessible from inside
the cabinet using the 4mm Hex Driver (A).
5
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Thank you for choosing BDI.
1.
2.
3.
3.
1.
2.
*
2.
*
Your BDI home theater cabinet is engineered to include a range of adjustments. Please read and retain this guide so that
you can fully enjoy the look and use of your cabinet for years to come.
Unless manual leveling is required or you wish to prevent the cabinet from rolling, you may prefer to keep the cabinet’s
levelers up and off the floor. This allows easier cabinet movement for greater access to rear panels and wiremanagement, and permits easier cleaning/vacuuming underneath the cabinet.
By following the steps in this guide, you can be sure that your BDI cabinet is in optimum tune and adjustment. If you need
additional assistance, contact BDI at customerservice@bdiusa.com.
Fine tuning your BDI Home Theater Furniture
After unpacking and assembling your cabinet, inspect it to be sure that it is sitting level on the floor, that all doors appear
level, and that they open and close freely without rubbing or binding.
Due to uneven floors or perhaps gentle jostling during shipment, your BDI cabinet may not appear to be in perfect
alignment when first assembled or when loaded with heavier electronic equipment. Such
alignment issues are usually minimized or eliminated with only a few minor adjustments.
STEP 1 - Level the cabinet (if needed)
Levelers are integrated into each leg assembly and are accessed from outside the
cabinet. If your floor is uneven, you may extend one or more levelers (with the provided
Leveler Wrench (C)) to attain a level, stable cabinet placement. Turning the leveler
clockwise will extend the leveler; turning it counter-clockwise will retract it.
INCORRECT! Door is
out of alignment with
the rest of the unit.
CORRECT! Door is
sitting squarely and
evenly spaced on tops
and sides.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and should open and close freely without rubbing against the door
frame.
If the cabinet’s doors appear out of alignment,
this condition can be corrected with minor
adjustments to the European hinges on each
door.
Because these hinges are infinitely adjustable,
3.
2.
3.
1.
2.
1.
adjusting one hinge element can sometimes cause
the need for adjustments to other elements.
But with a few adjustments, you can modify the
orientation of the cabinet doors to make sure that
they hang perfectly within your cabinet.
Figure 2Figure 1
Use Phillips Screwdriver (B) to adjust Novia’s door hinges:
•ByadjustingScrew 1, the door will move LEFT or RIGHT within the frame. Make minor adjustments at
both top and bottom hinges for best results.
•ByadjustingScrew(s) 2, the door will move UP or DOWN within the frame (the top and bottom
hinges must be adjusted the same degree).
NOTE: If your hinges have a Slotted Mounting Plate (as shown in Figure 2): Loosen Screws 2 one
complete turn, raise or lower door, then hold in position while tightening Screws 2 (on both hinges).
•ByadjustingScrew 3 the entire door will move IN or OUT, opening or closing the gap between the
door frame and cabinet. (This screw rarely needs adjustment.)
6
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...