Mi r a g e
8224
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
Mirage is engineered for easy assembly. Carefully follow this procedure
A - Phillips Screwdriver
x 1
B - 4mm Hex Driver
x 1
C - Dowel Pin x 8
D - Cam Bolt x 2
to prevent any damage.
Placement and Maintenance
Mirage is designed for indoor use on level floors. Clean glass with glass
cleaner; steel parts and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some components
E - Cam Fastener x 2
are shipped inside the cabinet. The assembly workspace should be a nonmarring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
F - Leg Assembly
x 2
G - Front Rail x 1
Step 2
Remove Pre-Installed Adjustable Shelves (L)
H - M6 x 70mm Bolt x 4
I - M6 x 73mm Bolt x 2
J - Barrel Nut x 6
Pre-installed on M6 x
70mm Bolt (H) and M6
x 73mm Bolt (I)
K - Center Leg x 1
L - Assembled Cabinet
x 1
M - Adjustable Shelf
x 2
L
N - Back Panel x 2
Designed by Al Glass and Cristian Wicha.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2009, BDI
Made in China. 080709v1
1
Step 3
Build Base Assembly
Press Dowel Pins (C) into place at indicated locations near ends of
Front Rail (G), then install Cam Bolts (D) at indicated locations using
provided Phillips Screwdriver (A). Then join the Front
Rail (G) and Leg Assemblies (F) together,
aligning holes for Cam Bolts (D) and Dowel
Pins (C).
Once Dowel Pins (C) and Cam Bolts (D)
are fully inserted into the respective holes,
fasten together by inserting Cam Fastener
(E) and turning it approximately one-half
turn clockwise using
Phillips Screwdriver (A).
C
G
F
D
E
Step 4
Install Base Assembly and Center Leg
With Assembled Cabinet (L) resting safely on its back surface,
press Dowel Pins (C) into place at six (6) indicated locations of
cabinet bottom. Then install built Base
Assembly to Cabinet bottom using
M6 x 70mm Bolts (H) and Barrel
Nuts (J), and tighten with Phillips
Screwdriver (A). Next install Center
Leg (K) to Cabinet bottom using M6 x
73mm Bolts (I) and Barrel Nuts (J),
and tighten with Phillips Screwdriver
(A).
NOTE: As Barrel Nuts (J) are
preinstalled on ends of M6 x 70mm
Bolts (H) and M6 x 73mm Bolts
(I), first loosen and remove Barrel
Nuts from Bolts, then insert Bolts
through the Base Assembly and
Center Leg from bottom, fastening
into place with Barrel Nuts from
the top (inside cabinet).
C
H
C
H
C
I
I
C
H
C
I
C
I
2
H
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Step 5
Re-install Shelves
Position the cabinet right side up and then re-install Adjustable
Shelves (M ).
For more information about the adjustable levelers
B
and troubleshooting assembly, be sure to check out
“Fine tuning your new BDI Mirage Home Theater
Furniture” at the end of these instructions.
The adjustable leveler glides on the
bottom, mid section of the cabinet
are accessible from inside the
cabinet using the Hex Driver (B).
Step 6
Install Back Panel
Install both Back Panels (N) to the backside of the cabinet by inserting top edge in upper channel, then tipping bottom edge forward
and into lower channel.
NOTE: : Velcro straps are included as wire management for your
convenience.
A
The shelf pins located inside the
left and right cabinet space may
be repositioned, allowing you to
raise or lower each shelf to the
desired level.
N
2
1
Optional Flat Panel TV Mount
This BDI cabinet is compatible with BDI’s Arena Flat-Panel TV Mount #9972
(sold separately), with the following features:
•
accommodates most TVs up to 60”, 175 lbs
swivel allows rotating for optimal viewing •
allows adjustable TV mounting height •
accepts and routes cables to and from the TV •
For more information, visit www.bdiusa.com
3
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Fine tuning your new BDI Mirage Home Theater Furniture
1.
2.
3.
3.
1.
2.
*
2.
*
These steps are to be followed after you have unpackaged and completed the simple assembly instructions for your
Mirage AV stand. Due to jostling in freight or perhaps an uneven floor, the doors and drawers on your Mirage stand
may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that
depending on your situation, patience and a bit of trial and error are required. The high-quality European hinge hardware
is infinitely adjustable, but changing one element can cause the need for further adjustments. Through a little adjustment,
you can modify the orientation of the cabinet doors to make sure that they are sitting perfectly on your Mirage unit.
STEP 1 - Level your Mirage unit
Levelers are integrated into each leg assembly and are accessed from inside the cabinet. If your floor is uneven, you may
extend one or more levelers (with the provided Hex Driver (B)) to attain a level, stable cabinet placement. Turning the
leveler clockwise will extend the leveler; turning it counter-clockwise will retract it.
INCORRECT! Door
is out of alignment
with the rest of the
unit.
CORRECT! Door is
sitting squarely and
evenly spaced on tops
and sides.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame.
If the cabinet’s doors appear out of alignment, this condition can be
corrected with minor adjustment to the European hinges on each
door.
Because these hinges are infinitely adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other
elements. But with a few adjustments, you can modify the orientation
of the cabinet doors to make sure that they hang perfectly within your
cabinet.
Use a Phillips screwdriver to adjust Mirage’s door hinges:
•ByadjustingScrew 1, the door will move LEFT or RIGHT within
the frame. Make minor adjustments at both top and bottom hinges
for best results.
•Byadjusting Screw(s) 2, the door will move UP or DOWN within
the frame (the top and bottom hinges must be adjusted the same
degree).
NOTE: Loosen Screws 2 one complete turn, raise or lower door,
then hold in position while tightening Screws 2 (on both hinges).
•ByadjustingScrew 3 the entire door will move IN or OUT,
opening or closing the gap between the door frame and cabinet. (This
screw rarely needs adjustment.)
4
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...