BDI 8157 User Manual
Ci r r u s
8157
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Component List
A - Phillips Screwdriver
x 1
B - 4mm Hex Driver
x 1
C - Dowel Pin x 10
D - Cam Bolt x 4
E - Cam Fastener x 4
F - Leg Assembly
x 2
G - Rear Rail x 1
H - Front Rail x 1
I - Assembled Cabinet
x 1
J - Washer x 8
K - 1/4-20 x 2”
Machine Screw
x 4
Cirrus is engineered for easy assembly. Carefully follow this procedure to
prevent any damage.
Placement and Maintenance
Cirrus is designed for indoor use on level floors. Clean glass with glass
cleaner, and steel parts and wood veneer with a moist cloth.
Step 1
Unpack and Identify
Unpack and identify the components at left. Note that some components
are shipped inside the cabinet. The assembly workspace should be a nonmarring surface such as carpet. For missing hardware pieces, please
contact BDI Customer Service at customerservice@bdiusa.com. For all
other concerns, please contact your BDI Retailer.
Step 2
Build Base Assembly
Install Cam Bolts (D) near front and rear edge of each Leg Assembly (F)
using provided Phillips Screwdriver (A). Next, insert Dowel Pins (C) into
holes at ends of Front Rail (H) and Rear Rail (G). Then join both Rails
and Leg Assemblies together, aligning holes for all Cam Bolts and Dowel
Pins.
Once all Cam Bolts and Dowel Pins are fully inserted to the respective
holes, fasten together by inserting Cam Fastener (E) and turning about
one-half turn clockwise using Phillips Screwdriver (A).
L - 1/4-20 x 3 1/2”
Machine Screw
x 4
M - 1/4-20 x 1 1/4”
Machine Screw
x 2
N - Center Leg x 1
O - Sliding Door x 2
P - Back Panel x 2
Q - Adjustable
Center Shelf
x 1
R - Adjustable Shelf
x 2
Designed by Matthew Weatherly.
These distinctive product configurations are protected by US and international
patents, trade dress, and/or copyright laws.
BDI are trademarks of Becker Designed, Inc.
All Rights reserved. ©2009, BDI
Made in China. 8157REV121109v2
F
D
C
G
E
F
G
H
E
D
H
C
F
1
Step 3
Fasten Base Assembly to Assembled Cabinet (I)
After inserting Dowel Pins (C) at each of the four corners of the Base
Assembly, install Base Assembly to Assembled Cabinet (I) with Front
Rail (H) oriented towards cabinet front (see drawing).
Fasten into place using Washers (J) and ¼-20 x 2” Machine Screws
(K) at Front Rail (H), and using Washers (J) and ¼-20 x 3-1/2”
Machine Screws (L) at Rear Rail (G) and provided Hex Driver (B).
C
NOTE:
Levelers are present at
the front and rear underside
of each Leg Assembly. Each
Leveler is manually adjustable
by hand-turning to extend or
retract to the desired position.
Such adjustment will help offset
uneven flooring and/or will
prevent the cabinet from
rolling.
Step 4
Install Center Leg
Install Center Leg (N) to cabinet’s bottom panel using ¼-20 x 1-¼”
Machine Screw (M) and tighten with provided Hex Driver (B).
N
J
K
J
L
M
M
M
N
2
a s s e m b l y i n s t r u c t i o n s
b d i u s a .c o m c u s t o m e r s e r v i c e @b d i u s a .c o m
Loading...