Page 1
SIGMATM 6901/6903
DESK/COMPACT DESK
bdiusa.com
customerservice@bdiusa.com
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today and you will be entered to win free a BINK
table from BDI. www.bdiusa.com/product-registration/
Placement and Maintenance
Sigma™ Office furniture is designed for indoor use on level floors. Clean
glass with glass cleaner, and other surfaces with a moist cloth.
Your Sigma™ Office furniture is engineered for easy assembly. Carefully
follow this procedure to prevent any damage. Do not use power tools for
assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, please contact BDI Customer Service at:
customerservice@bdiusa.com.
For all other concerns, please contact your BDI retailer.
Model 6901
C4 Metal Tray x 1
C1 Glass Panel x 1
shown below
Hardware:
T1 4mm Hex Wrench
H1 M6 x 12mm Screw x 22
C5 Drawer Liner x 1
C8 Left Leg x 1
Designed by BDI Studio.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Sigma & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2019, BDI
Made in Turkey. 02.18.2019
C6 Upper Trough x 1
C9 Right Leg x 1
C4 Desk Frame x 1
C10 Cord Conduit x 1
C7 Lower Trough x 1
C2 Back Panel x 1
C3 Front Panel x 1
Page 2
Step 2 - Place desk frame C4 upside down on a padded surface, such as a carpet. Attach left leg C8 and
right leg C9 to desk frame C4 using screws H1 and hex wrench T1.
T1
H1 x 8
C8
H1
H1
C9
C4
Drawer front
this side
2
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Page 3
Step 3 - Orient the upper trough C6 as shown between the back leg frames. Attach the upper trough C6
to the leg frames with screws H1 and hex wrench T1.
T1
H1 x 4
H1
H1
C6
3
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Page 4
Step 4 - With help from another person, attach lower trough C7 to inside of left and right leg using
screws H1 and hex wrench.
H1
H1
T1
H1 x 4
2 Person Ta sk
C7
4
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Page 5
Step 5 - With the help of another person, position the desk on its feet. Carefully position the glass top C1 on
top of the desk with the rectangular blocks aligning with the rectangular openings on either side of the drawer.
Attach the glass top C1 to the desk frame using screws H1 (going through the 6 metal tabs) and tighten with
the hex wrench.
Step 6 - Install the metal tray C4 by inserting the 2 bent metal tabs into the corresponding slots on the bottom
of the top trough as shown.
H1 x 6
rectangular blocks
metal tab
2 Person Ta sk
rectangular blocks
C4 metal tray
tabs go
into slots
5
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Page 6
Step 6 - The Sigma desk provides a flip down metal tray designed to hold surge protectors. Lower the metal
tray as shown. Position your surge protector. Use the slots in the upper and/or lower troughs to route the
cord to a electrical outlet.
Note: The Sigma Desk is designed to permit placement in front of an electrical outlet for easier wiring access (as
shown below).
(not provided by BDI)
metal tray
electrical outlet
6
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Page 7
Step 7 - Install Front Panel C3 as shown. The top inside has pre-installed magnets that hold the panel in
place.
C3 Front Panel
Step 8 - The Back Panel C2 conceals wire management when the desk is located in the middle of a room.
Install C2 as shown. The top inside has pre-installed magnets that hold the panel in place.
C2 Back Panel
7
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Page 8
Step 9 - Open the drawer and Install the drawer liner C5.
C5
Step 10 - (Optional)
If plugging into a floor outlet, the cord conduit C10 can be attached to one of the back legs. Remove the
adhesive backing from the back of the cord conduit and stick it directly onto the inside edge of the leg closest
to the outlet. Press firmly. Route cords inside.
C10
8
SIGMA 6901/6903
DESK/COMPACT DESK
customerservice@bdiusa.com
bdiusa.com
Loading...